Search Documents

By B. Kruger

After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron. The iron-free (less than 1% Fe) converter matte is granulated and sent to the base metals and precious metals refineries for further processing. During the smelting and converting processes two distinct gas-strength gas streams are produced: ?The Peirce Smith converter off-gas contains 4%?9% SO2which is treated in a conventional sulphuric acid plant to produce 94% H2SO4. ?The electric furnace off-gas contains 0.9% SO2which was (until September 2002) vented through a 91- metre high stack to atmosphere. In October 2002 Impala Platinum commissioned a SULFACID® plant at its smelter in Rustenburg, which recovers the SO2from the electric furnace off-gasses into a weak sulphuric acid solution. The SULFACID® technology utilizes wet activated carbon to oxidize the SO2toSO3. The SO3reacts with the water on the catalyst and is washed off the catalyst bed as a sulphuric acid solution with up to 13 wt. H2SO4. The plant operates at 60ºC and at atmospheric pressure. The SULFACID® technology is widely used in the pigment industry. This is, however, the first application of the technology on electric furnace off-gas. Keywords: SO2, sulphuric acid, electric furnace, off-gas, SULFACID®

Jan 1, 2004

By R. P. Carreker

ONE of a series, this report is concerned with the experimental documentation of the deformation behavior of pure metals over a wide range of temperature. Previous reports in the series describe the creep behavior of platinum1 and aluminum2 and the tensile behavior of copper,&apos; silver,& and molybdenum.5 Subsequent reports will describe the creep behavior of copper and silver and the tensile behavior of platinum, thus providing extensive creep and tensile data on four face-centered-cubic metals tested under comparable conditions. Material Two lots of high-purity aluminum were used in this investigation. One lot, designated AC, was obtained direct from the Aluminum Co. of America as high-purity aluminum in notch-bar form. A typical analysis of this type of aluminum is 0.006 pct Si, 0.015 pct Cu, 0.006 pct Fe, and 99.975 pct Al. Lot BS was obtained from J. I. Hoffman of the Bureau of Standards as a portion of the Aluminum A described in his report of the redetermination of the atomic weight of aluminum.6 Lot BS originated with the Aluminum Co. of America also, and was received in the standard notch-bar form. A detailed chemical and spectroscopic analysis of lot BS has been published.6 Principa1 impurities were 0.006 pct Si, 0.003 pct Fe, 0.002 pct Cu, and >99.987 pct Al. Samples were processed identically by room-temperature swaging and drawing to 0.030 in. diam wires from approximately ½ in. diam rods that were machined from the notch-bar pigs. Samples were cut from the cold-drawn wire, placed in a grooved graphite block in groups of thirteen, and annealed in air for 1 hr at each of several temperatures, with the results shown in Table I. The two lots of aluminum responded quite differently to annealing, the behavior of aluminum AC suggesting that its grain growth was controlled by impurities. The recrystallization texture of aluminum of similar purity comparably treated has been reported as predominantly <111> fiber with some <100> fiber present.7 Testing Procedure The testing procedure and method of analyzing the data have been described previously.2,3 Annealed specimens of 5 in. gage length were tested in an Instron tensile testing machine at a constant head motion corresponding to a strain rate of 0.04 min-&apos; at a number of temperatures. Instantaneous tenfold rate changes were employed in some tests to deter-

Jan 1, 1958

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001

By F. J. Williams

BARITE, naturally occurring barium sulphate, is the chief barium mineral that is produced commercially. Barite is also called "barytes," "heavy spar," sometimes "baryta" and, locally in Missouri, "tiff." Pure barite is white, opaque to transparent. It crystallizes in the orthorhombic system, frequently with twinning. Impurities cause a wide variation in color, commonly buff, gray and white with irregular reddish iron stains. Less frequently found are shades of yellow, green, blue, brown, and black. The rock is brittle and breaks with an uneven fracture, although specimens from some of the residual deposits, particularly in Missouri, appear to have a cleavage due to the separation of the different layers of deposition. The hardness varies from 2.5 to 3.5 on Mohs&apos; scale and different localities are said to produce either "hard" or "soft" barite. This generally refers to the ease of grinding of the product. The specific gravity of pure barite is 4.5 and this will vary downward, depending on the impurities present. The mineral has a white streak and a pearly to vitreous or sometimes stony luster. Pure barite contains 65.7 pct BaO and 34.3 pct SO3. Witherite, native barium carbonate, is not mined in the United States at the present time although a number of occurrences have been reported. A small quantity of witherite has been removed from a mine at El Portal, California, but the area high in witherite was small and soon depleted. The bulk of the deposit is predominantly barite. Great Britain is the world source of witherite and small quantities are imported into the United States. DISTRIBUTION OF DEPOSITS Occurrence of barite is widespread; it has been reported on all the continents and in all the major countries of the world. Deposits vary from those containing millions of tons down to scattered rock fragments

Jan 1, 1949

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6&nbsp;g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

Three types of communication systems have become popular in solving communication requirements underground: Loud-speaking pager phones, carrier current phones, and magneto ringing phones. Basically, all three are simply single-channel party line systems. Although these systems are quite reliable, the single channel creates a variety of problems. For example- 1. Since no call is confidential, messages are sometimes purposely made vague, especially if accidents or safety topics are being discussed. 2. A potential user must literally "wait in line" until the channel becomes clear for his use; thus, when foremen have to wait to call in reports or supply requests, this single chan-nel creates a serious productivity bottleneck. 3. In many large mines, there are independent branch lines that must be tied together by a dispatcher, adding further delays to the system. To solve these problems, some mines have installed other phone systems-mostly commercial dial phones in industrial enclosures that offer extra channel capacity and private line features. Others have installed a system that combines both dial- and page-phone features in a single unit. Although these do represent improvements, they do not truly solve the overall problems that face modern mines. Besides extra channels, a communication system should have the following features to enhance productivity and safety: 1. A means of paging a roving miner to alert him that he is wanted on the phone. 2. Wireless-to-wired system interconnects by which a miner can talk on the wired phone system by using a remote portable radio. 3. Remote monitors that alert personnel when there is a toxic or explosive gas buildup. 4. Control interfaces that allow remote control of fans, pumps, or other devices. 5. Transmitters and receivers that can serve as emergency links. 6. Loopback that allows an alternate path of communications if the main path is cut. This chapter focuses on equipment and methods to meet the special communication needs of individuals in various places of the underground mine. The communication requirements can be broken down into four categories: 1. The mine entrance (shaft communication). 2. Permanent and semipermanent locations (shop areas, lunchroom, crusher stations, etc.). 3. Mining areas (the room-and-pillar sections, longwall faces, block caving areas, etc.). 4. Haulageways (tracked trolley haulage, diesel, belt haulage). Methods of implementing systems to meet the communication needs of these areas are described in sections 3.2 through 3.5. Section 3.6 discusses methods of satisfying special communication requirements that exist. Major topics in this category include communications with roving personnel, the isolated miner, and motorman-to-snapper communications. Emergency communication systems are described in section 3.7.Detecting and

Jan 1, 1984

By Gerald Stolarczyk

The Radio Imaging Method (RIM) is based upon electromagnetic (EM) wave propagation in the coal seam waveguide. The radio geophysics theory underlying RIM was developed by Hill of the national Institute for Science and Technology (Hill, 1984). Recent advances in radio geophysics instrumentation have increased operating range in the coal seam waveguide to almost 3,000 feet. This paper describes RIM longwall panel reconnaissance scans and tomography results.

Jan 1, 2006

By E. I. Larsen, A. S. Doty, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850&apos; and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By A. S. Doty, E. I. Larsen, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850&apos; and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By E. De Souza

Two comprehensive surveys, which focus upon backfill practices and the economics of backfilling in underground mines in Canada, have been conducted. The two surveys were designed to assess operational practices and costs associated with the wide scope of filling operations that must be met by individual mines, ranging from raw material feed to the preparation plant, through underground backfill transportation, to in-stope product placement. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database of information upon which they might compare their own practices and costs with present trends throughout the industry.

May 1, 2003

By H. J. Handewith

This paper explores the state-of-the-art of mechanical rock drilling and boring methods in use in the year 2000. It covers the basic mechanisms of cutting tool design and outlines the current understanding of related rock fracture methods. It provides suggestions for future research needs and discusses the mining and construction markets that are driving these needs.

Jan 1, 2001

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By I. Gaballah

Spent hydrorefining catalysts may contain 4 to 6 % of COO and/or NiO, 8 to 16 % of Moo3 and up to 10 % V205 generally supported by alumina. Raw samples are roasted in order to eliminate carbon, sulfur and hydrocarbons contained in the spent catalysts. The roasting optimum temperature and time are 500 "C and 7 hours. Selective chlorination of roasted samples with Cl2 + air, Cl2 + N2 and Cl2 + CO is investigated in order to recover the valuable metals. Depending on the chlorination it is possible to recover more than 80 % of the Ni and Co about 95 % of the Mo and up to 80 % of vanadium compounds. Cobalt and nickel chlorides are obtained by leaching the chlorination residues&apos; by acidified water. Molybdenum and vanadium chlorides and/or oxychlorides are obtained by selective condensation from the vapor phase. The chlorination of the catalyst support, Al2O3, can be limited to less than about 5 %. Besides the reaction temperature and time, the oxygen partial pressure of the chlorinating gas mixture appears to be the key factor for the reactions&apos; selectivity.

Jan 1, 1993

By Bruce K. Hebblewhite

This paper provides an overview of the international ?state of the art? with respect to underground coal mining methods used in seams of thickness greater than 4.5 m, through a review of a selection of high performing thick seam mining operations around the world?both Single Pass Longwall (SPL) and Longwall Top Coal Caving (LTCC). The paper discusses the recent operational experiences from these selected faces, together with the ground control issues faced, and identifies some of the major, inherent geotechnical factors that can influence the mining method selection, design criteria, and ultimate performance, from both an operational and safety perspective. It is clear that both of these methods are developing quickly? not only from an operational and equipment perspective, but also from the understanding of critical geotechnical criteria. There is an increasing role for both methods in thick seam environments, although the higher SPL faces will only be successful in the near to mid-term under benign geotechnical environments. Regardless of the method, a thorough understanding of the critical geotechnical factors is a key to successful implementation of either method.

Jan 1, 2013

By Ann Barron, Mark Abernethy

Along with the immense benefit of modern explosives seismic and acoustic effects caused by their detonation can be disruptive and alarming to many people. Claims range from affecting sexual performance to outright demolition of a residential structure. Regardless of the quality of the blast design and other precautionary measures, the inherent danger posed by the use of explosives often leaves residents searching for restitution. Consequently, many blasting companies today find themselves at the center of litigation. In the event that a blasting complaint proceeds to litigation your case will not be decided on “reasonable doubt” as in criminal trials. Instead, the jury will be instructed to decide guilt or innocence on a “preponderance of the evidence” presented. Even if you are able to present the best and most complete evidence that you have not caused the claim, the jury may rule in the favor

Jan 1, 2004

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By Xun Zhang, ZhiLong ZHAO, Lifeng Zhang, Huiqing Tang

A two-dimensional gas-solid model has been developed for examination of the blast furnace (BF) performance under hot charge operation. Simulation conditions were obtained from the actual operation conditions of the BF with inner volume of 2500 m3 and molten iron output of 6250 ton hot metal (THM) per day. The simulation results indicate that hot charge operation could change the thermal state of the BF in the region above cohesive zone (CZ) and has little influence on the thermal state of CZ zone and the region below CZ; it could intensify both the indirect reduction of the ore and the gasification of the coke in the region above the CZ. The optimum temperature for hot charge operation is 750 K, under which, a coke rate reduction of 25 kg/THM could be obtained.

Mar 1, 2017

By D. Kump

The Bullfrog Mine is an underground gold mine that uses the underhand-cut-and-fill mining method. The portal was established on June 18, 1991. Mining is expected to be completed by the summer of 1999. This paper starts by discussing what it took to get from nothing to 2000 tons-per-day backfill, and ends with a hindsight commentary on things that did and did not help.

Jan 1, 1999

By Jon I. Voltz

The U.S. Bureau of Mines has conducted fundamental coal fragmentation studies to evaluate the effects of impact energy and direction of bedding planes on dust generation, size distribution, and impact-output energy relationships. Product size distributions were obtained for the fragmented samples by screening to minus 150 mesh. The minus lS0-mesh fines were analyzed with a light scattering photometer with a measurement range of 176 to 1.9 /.tm. Increased input energy produced a significant increase in the weight of plus 3/8-in material for impact perpendicular to the bedding planes. No significant trend was observed for parallel impact. Impact direction had little influence on dust size distribution, and input versus output energy relationships. As expected, total airborne dust measured at time of impact and percent particulates below 11 /.tm in size generally increased with increased input energy for both directions of impact. Energy used for sample fragmentation increased with increased energy input.

Jan 1, 1989

By A. W. Davis

"The Red Rose mine is in the Rocher Deboule mountains about 8 miles east of Skeena Crossing and a like distance south of the town of Hazelton; the most northerly settlement on the Prince Rupert line of the Canadian National railway and 177 miles northeast by rail from Prince Rupert. The mine workings are on the north side of Balsam or Red Rose creek; a tributary of Juniper creek that drains via Kitseguecla river into the Skeena near Skeena Crossing. A truck road 11 miles long extends from Skeen a Crossing (elevation 650 feet) to the Red Rose mill (elevation 4; 100 feet). The mine workings lie between 5; 600 and 6; 300 feet above sea-level. Mine and mill are connected by a 1-mile aerial tramway and a tractor trail.The Red Rose claims were staked about 1910 by prospectors attracted to the district by the construction and near completion of the railway between Prince Rupert and Jasper. For a number of years interest centred in prospecting a sheared zone exposed in a ravine between elevations of 5,425 and 5,825 feet. Several adits were driven and some high gold assays were obtained in vein quartz in the sheared zone, but this work did not develop sufficient ore and the property finally closed down. In the early twenties of this century tungsten minerals were discovered in the northern extension of the vein, but nothing was done to test this deposit. Finally, in 1940, spurred by the wartime demand for tungsten, the Consolidated Mining and Smelting Company of Canada drilled the tungsten-bearing vein, and although results were none too encouraging, underground work was begun in June 1941. The latter work disclosed substantial amounts of ore. A small mill, subsequently enlarged, began operation early in January 1942 and by the autumn of 1943 some 1,194,000 pounds of tungsten concentrate had been recovered. Mining ceased in November 1943 because of orders from the Metals Controller that no more shipments would be permitted."

Jan 1, 1954