Search Documents

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

By N. Grosland, G. Kopp, L. Frey-Law, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Heavy equipment manufacturers have made a long-term commitment to minimize operator vibration exposure for comfort, performance, and health reasons. Domestic and international guidelines/standards and EC laws dictate exposure limits based on measurement of vibration at the interface between the seat and the operator’s buttocks using seat-pad accelerometry.1-4 This is historically based on the assumption that the only major source of vibration is transmitted through the seat pan. However, vibration may also be imparted to the head and neck via the steering wheel and/or arm-rest controls and a relatively rigid upper body.5 Unfortunately, little is known regarding the influence of arm position on head and neck motion. The purpose of this study was to investigate relative head and trunk motions during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree-of-freedom vibration system. An 8-camera Vicon motion capture system operating at 200 frames per second, recorded the motion of reflective surface markers on 5th, 50th, and 95th percentile right-handed male subjects, using 3 seat and control configurations (steering wheel (SW), floor mounted armrest controls (FM), seat-mounted armrest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). The relative motions (change in distances) from the marker over the xiphoid process (caudal end of sternum) to markers over each shoulder, each mid-clavicle, the presternal notch, and to each of four markers on a tight band around the head were calculated (12,001 frames, 6-dof motion only). As a rigid body control, distances between markers on the head band were also monitored. The standard deviation (SD) of the 12,001 distances between pairs of markers was normalized by the mean (L) of the associated distances producing: SD/L which was used as a measure of motion. Error assessments were also performed by analyzing the motion between relatively fixed markers (on the headband). A repeated measures analysis of variance was used to evaluate the results. While five ride files were used, only one ride file containing significant lateral acceleration components was analyzed for comparing the effects of two armrest controls versus use of a steering wheel for this part of our study. Results Values of SD/L between the points on the relatively rigid head band were consistently small and similar to each other for all conditions with one exception due to treatment (SM v SW, p=0.0145). SD/L between the markers over the xiphoid process and the presternal notch, another region that should be relatively rigid, were also similar to each other for all conditions. Use of floor-mounted, arm rest controls versus a steering wheel produced a significant increase in the value of SD/L between the xiphoid process and: the right shoulder marker (92%, p=0.0316), the right mid-clavicle marker (47%, p=0.0478), and the right-front marker on the head band (28%, p=0.0182). Use of floor-mounted, arm rest controls versus seat-mounted, arm rest controls

Jan 6, 2006

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

By L. C. Ilaley

The Buresa. ot Mines at its Pittsburgh Station conducted tests aa earl7 a.a 1911 looking into the satety of miniature electric bulba. The first teata were maie with bulbs euch as were being sold with the partly developed lamps then on the market. 'l'he.sa aarly teats demonstrated the da.nger of using minia.tu:re bulbs in explosive mine atmospheres unless the current that enet gized the glow!ng filament was in aome minner inter.N.ptecl if the glass surrounding the filanant should be broken.

Jun 1, 1922

By Scott Ellenbecker

Mining has evolved in recent years, taking steps forward in the way that the industry is considerate of the environment and the communities in which it operates. Technology plays a major role in that evolution. Osisko Mining?s Osisko Mine near Malartic, Quebec is developing a new way of doing business. One manager said, ?We are building the Osisko culture,? but the company is doing many things that could become industry changers. Much of the change is driven by mine ownership and management to offer a better workplace and better community relations. Mining equipment manufacturers are changing, too, by engineering products with more operator comfort, fuel economy, ease of maintenance and more cleanly designed machines. And for those drills working close to communities, smaller bore sizes and sound retention are just two changes for the better.

Jan 1, 2012

By J. J. Henn

A process is evaluated for recovering metallurgical-grade manganese are from the low-grade manganiferous iron ores of the Cuyuna Range, Minnesota. The process, developed by the Bureau of Mines, employs high-temperature sulfatization of the are to form manganese sulfate and reduction of the are to convert the iron to a magnetic oxide. The roasted ore is water-leached to dissolve the manganese sulfate, which is then separated from the leach residue, is crystallized, and is calcined to produce the manganese product. Iron is recovered from the leach residue by magnetic separation, and is pelletized and calcined to produce byproduct iron ore pellets. The fixed capital cost for a plant yielding a product containing 100 tons of manganese per day is $19.6 million on a mid-1970 basis when the raw are contains 4.84 percent manganese. The estimated operating cost of the plant is $211 per ton of contained manganese. Graphs are included to show the effects of ore cost and varying manganese content of the raw ore on the estimated operating cost.

Jan 1, 1972

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

By M. S. Moats, A. Luyima, W. Cui

"Organic smoothing additives are used to produce dense, thick, high-quality cathodes in copper electrowinning. Glue had been used traditionally and is still used in operations that do not employ solvent extraction to produce the electrowinning electrolyte. With the advent of solvent extraction–electrowinning, guar started to be used and remained in use for many years as it does not affect the phase disengagement in solvent extraction. Recently, however, guar has been replaced by less-expensive saccharide- and polyacrylamide-based additives. This paper is the first of a series of four papers that examine saccharides and polyacrylamides as new additives for copper electrowinning. A review of previous research related to copper electrowinning additives is presented here, along with a selected review of additives in other copper electrodeposition systems.IntroductionThe recovery of copper from solution by electrowinning was first practiced in the early 1900s, but it was the combination of solvent extraction with electrowinning (SX-EW) in March 1968 at the Ranchers Bluebird Mine (Kordosky, 1992) that changed the landscape for the electrowinning process. Most copper electrowinning capacity is now associated with solvent extraction, though some copper is still won directly from leach solutions (Robinson et al., 2013). The ability to produce high-purity copper cathodes from SX-EW has taken the continued improvement of SX-EW technology over the past more than 40 years.One of the technologies that has seen improvement is that of the organic smoothing agents used during the electrodeposition of copper in the tankhouse. These organic additives are added to the acidic copper sulfate electrolyte during electrowinning to improve the smoothness, brightness and density of the copper cathodes. The organic additives that are presently in use are different from those used in 1999 (Jenkins et al., 1999). Over the past decade, many tankhouses have replaced the use of guar-based organic additives with those derived from other saccharides. Until now, there has been no comprehensive publication in the open literature on the behavior of these additives during copper electrowinning."

Jan 1, 2016

By R. J. Barnes

Consider a typical blast at a surface gold mine in North America. For example, the low-grade area of Bench 4000 at AMAX Gold's Sleeper Mine (Winnemucca, Nevada). Bench 4000 is 20 feet high (=6m) , and blast holes are drilled and sampled on a 14 foot by 14 foot square grid (a4m x 4m). A representative blast includes between 50 and 150 holes, encompassing 15,000 to 45,000 tons of material (w14,000 to 41,000 metric tons).

Jan 1, 1989

By Eduardo Gomes Vieira

O Projeto 4ª Pelotização surgiu com o propósito de aumentar a capacidade de produção de pelotas da Samarco em 37%, por meio da implantação do 3º Mineroduto, com capacidade de 20 Mt/ano, a 4ª Usina de Pelotização com capacidade de 8,25 Mt/ano e o 3º Concentrador com capacidade de 9,5Mt/ano. O projeto proposto visa estruturar o processo de Manutenção do Concentrador 3 através do sistema de gestão de dados utilizado pela Samarco Mineração, o software SAP, com foco na criação de um modelo taxonômico de níveis hierárquicos contendo informações técnicas dos novos equipamentos e respectivos sobressalentes, dando base para definição de uma política de estoque, a implementação de planos de manutenção e estudos de confiabilidade. Objetiva a redução do Risco Operacional, consolidando no sistema os processos que compõem a função manutenção, referente à terceira Usina de Beneficiamento de Minério de Ferro da Samarco Mineração. Para isto, foi utilizada a metodologia Kaizen para estruturação e desenvolvimento do trabalho e estabelecimento de metas para controle das informações. Verificou-se uma grande demanda de avaliação de criticidade e cadastro dos equipamentos e sobressalentes, além disto, a falta de organização das informações de forma estruturada poderia acarretar dificuldades de se analisar itens faltantes. Foi necessário também o estabelecimento de critérios para implementação de planos de manutenção visando à preservação da integridade e funcionalidade dos equipamentos.

Aug 16, 2017

By H. H. Podgurski, J. C. M. Li, Y. T. Chou, F. N. Davis, R. A. Oriani

When an Fe-2 pct A1 alloy is nitrogemted at 500ºC with a gus tnixture (NH3-H2) in which the nitrogen activity has been kept Lou] enough to avoid the formation of iron nitride, a two-phase alloy is generuled which consists of AlN particles and a ferrite phase cotaining a heavy network of dislocations. The amount of nitrogen contained in such an alloy, when equilibrated with the nitrogenating atmosphere, far exceeds both that needed to satisfy the normal solution requirements of a Fe and that needed to convert all of the aluninuwi to AlN. This excess nitrogen is accounted for as being trapped on dislocations, adsorbed at the ferrite -AlN interface, and as an en-Iuznced lattice solubility in strained ferrite. This excessive uptake of nitrogen had previously been attribuled by other investigators to the formation of a nonstoichiornetric aluminum nitride. Isotope exchange experiments revealed various amomts of exchargeable N14 present in the originally nitrided samples that could not be removed by reduction with HS at 500ºC. This exchangeable nitrogen has been identified us that bound to the AlN -ferrite interface. Estimates of inter facial areas in alloys containing -3 pct by weight of A1N are as high as 10 sq m per g of alloy. ThE first1 of this series of papers described the experiments forming the basis for the elucidation of the mechanism of the formation of aluminum nitride particles within an Fe-A1 alloy. It was found that not only are dislocations necessary for the nucleation of the AlN particles but also the nitriding reaction in turn produces a dense network of dislocations in the ferrite matrix. It was also observed that nitrogen in excess of that needed for the formation of stoichiometric AIN is taken up by the alloy without the formation of an iron nitride. The present paper is an analysis of the excess nitrogen sorbed by the nitrided Fe-A1 alloy which considers the structure generated by the formation of the aluminum nitride particles. Because of the high density of dislocations, this system has proved to be quite useful in studying nitrogen-dislocation interactions. Wriedt and Darken2 have already reported such studies in a cold-worked ferritic steel. EXPERIMENTAL Nitrogen Sorption. The specimens of this alloy were cold worked (50 pct reduction) to 0.011 in. thickness and chemically cleaned in a 2:1 concentrated phosphoric acid-50 pct hydrogen peroxide solution before nitrogenation. The flowing nitrogenating atmosphere (11 pct NH3-89 pct H2) was established before the ni- trogenating temperature was reached. The same gravimetric and gas-flow equipment described in an earlier paper1 was also used in this investigation. Changes in nitrogen concentration were followed gravimetrically when establishing the isotherms. In the isotope exchange experiments, concentration changes were followed volumetrically. In some instances chemical analyses (Kjeldahl method) were used to check for material balances in both the gravimetric and volumetric procedures. Our objective was to obtain reversible nitrogen sorption isotherms for alloys equilibrated with NH3-H2 gas mixtures over a large range of nitrogen activity* and temperature. The *Defined as equal to PN H /P3/2 ,where P corresponds to partial pressure in atmospheres. Actually the nitrogen activity, aN, in the alloy equals K PNH3 /p3/2H2, where K is the equilibrium constant for the reaction NH3 = N + 3/2H2. upper limit for nitrogen activity was below that which would produce iron nitride; for reasons which will become apparent later, most of the sorption studies were made in the temperature range between 400" and 500'C. The alloy sample studied most extensively in this investigation was given a series of successive reductions (100 pct H2) and nitrogenating treatments at 500°C to attain a stabilized structure. Presumably some dislocations were lost during these treatments. Throughout most of the sorption studies, temperature was held at ± 1°C and the gas-phase composition was held to k0.2 pet NH3. Based upon the results of numerous diffusion experiments with this alloy* the 'Results to be published in a third paper of this series. times chosen for equilibration were considered more than adequate, Nitrogen Isotope Exchange. The first exchange experiments were carried out by circulating a measured quantity of H2 and NH3* (with a predetermined isotopic *The NH3 was synthesized over a synthetic ammonia iron catalyst using H2, and N2, enriched with N15. AS the NH3 was formed it was removed continuously from the gas phase by circulating the mixture through a refrigerated (78ºK) trap. When most of the nitrogen had been converted to NH3, it was distilled from the trap into a glass storage vessel. composition, N15/N14) over a nitrided specimen at 450°C in a closed glass system. Attempts to reach the exchange limit isothermally, i.e., an isotopic ratio (N15/N14) in the gas phase identical with the extractable nitrogen in the nitrided alloy, were futile. The exchange rate between the gas phase and the alloy was too slow, involving many days. To circumvent the slow exchange with the gas phase, measured amounts of N15 and N14 were introduced into the alloy by nitrogenating with an NH3-H2, mixture at 500°C containing an N15/N14 ratio of 7.76; the charged specimens were then sealed by allowing an oxide film to form over them in air, and in this final condition the specimens were subjected to 500°C in vacuum for various times during which isotope exchange was allowed to proceed within the specimen. It was estab-

Jan 1, 1970

By M. E. Wadsworth, C. H. Pitt

Nickel corrosion in sulfuric acid solutions at elevated temperatures and oxygen wer-pressures was imestigated. Weight loss was 1inear with time and varied directly with oxygen concentration. Independent variation of the possible active species in solution indicated that the undissociated sulfuric acid molecule plays an important part in the corrosion mechanism. The rate determining step was considered to be the adsorption of oxygen on a site containing adsorbed H2SO4. THE tendency for a metal to go into solution depends on a number of factors some of which are: 1) the position of the metal in the electrochemical series; 2) the type and concentration of corroding species in solution; 3) the concentration of oxygen in solution; 4) the type of film formed at the liquid-metal interface; and 5) the physical state of the metal. The corrosion of a metal in an aqueous solution may be considered to be a heterogeneous reaction that occurs at the liquid-metal interface. The reaction is generally considered to occur as a result of electrochemical potential differences within the system. Little work has been published in the literature concerning the corrosion of pure nickel. A great deal has been publistled dealing with the experimental and theoretical aspects of the over-all corrosion process. Evans,1 Uhlig,' and recently Todt 3 and Tomashoff,4 have published books which review the results of experiments which have been conducted on corrosion, and have developed some of the basic ideas of the more widely accepted theories of corrosion. Friend5 states that. nickel does not readily discharge hydrogen from any of the common nonoxidiz-ing acids and that a supply of some oxidizing agent is necessary for appreciable rates of corrosion. He further notes that at temperatures between atmospheric and close to boiling, corrosion rates tend to vary with concentration, temperature, and aeration in acid concentrations up to 25 pct. Whitman and Russel6 studied the effect of dissolved oxygen on a number of metals in acid solutions and found that oxygen accelerates the rate of corrosion of nickel in sulfuric acid. Flowers and Kelley7 in studying the action of dissolved CO, on electroplated nickel postulated that nickel dissolves as NiHCO3 in the presence of CO, and air. It was found that oxygen was necessary for corrosion to take place and that the rate increased with increasing amounts of oxygen in solution. Flowers and Kelley attributed the oxygen effect to cathodic depolarization. MacGillavry, Rosenbaum, and wensson' determined metal solution potentials of nickel in various electrolytes. They found that nickel has no tendency to corrode in alkaline solutions in the presence or absence of air. In acid solutions in the presence of air, metal solution potential increases in the order of 1/2 v were observed. This increase was attributed to probable chemisorption of oxygen on the nickel surface and the corrosion mechanism suggested was the interaction of H+ ions with the nickel oxide formed at the surface. Delahay9 observed the reduction of oxygen on various metals. A polarograph was used to measure the course of the reaction. With some metals hydrogen peroxide was produced as an intermediate compound. However, nickel was not considered to be a hdrogen peroxide producer. Van Rysselberghe 10,11 and associates attributed the accelerating effect of carbon dioxide on the corrosion process to the presence of percarbonic acid produced in solution reacting with the hydrogen peroxide. The percarbonic acid can be reduced at less negative potentials than hydrogen peroxide and as a result accelerates the reaction. EXPERIMENTAL Since a complete description of the apparatus used can be obtained elsewhere,12'13 no attempt will be made here to describe the equipment other than to note that it consisted essentially of an autoclave unit from which samples could be withdrawn periodically without disturbing the interior state of the autoclave. A titanium autoclave liner was used to protect the autoclave from the solution.

Jan 1, 1961

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

The statistical nature of the variability in detonation times of pyrotechnic delays is discussed, and how to evaluate the probability of required detonation intervals is shown. Some methods (analytical and stochastic) are given for designing blasts to ensure that any adverse effects on the variability in the delays is taken into account and minimised. Using computer models of blasts, detonation simulations can be used to check the initiation sequence for the probability of sequence reversals, indicating areas of high blast damage potential. Charge consumption rates, which relate directly to the resulting vibration levels, can be examined for their susceptibility to variation from delay variability. Models that synthesize vibration waveforms for production blasts, when taking delay variability into account, indicate the difficulty in vibration level prediction.

Jan 1, 1992

By J. Zwartendyk, A. Azis

"Every nation must decide how it should exploit its mineral resources so as to contribute most to its national objectives. It is argued that the present value of the future corporate income tax flow derived from mineral exploitation may serve as a useful indicator in moving toward a taxation policy that would contribute optimally toward the greatest public benefit.The future stream of corporate income taxes depends largely on the mineral endowment, consisting of deposits now being mined, known unmined deposits, and unknown deposits.Unknown deposits may be estimated by geological inference. Both known and unknown deposits can be categorized according to grade and size, and divided into economic and uneconomic deposits on the basis of certain prices, costs, rate of return and taxation levels.Computer simulations can be run of discounted cash flow models at various taxation levels to show the impact of taxation changes on future tax revenues."

Jan 1, 2014

By Eugene A. Stephenson

In most instances the fluids produced from underground reservoirs have been described as they appear at the surface, and usually it has not been necessary to distinguish between surface and reservoir phases. More recently it has become imperative to recognize the fact that changes in phase may occur between the reservoir and the receiving unit. The simple terminology of "wet" and "dry" gases and "crude petroleum oil" served our needs fairly well in the shallow, low-temperature and low-pressure fields. It has been left to the legislatures, regulatory commissions, and courts to decide whether a field is or was a gas field, an oil field, or both. This they have done by direct definition and also by implication. For example, in Texas:' (d) The term "gas well" is any well (a) which produces natural gas not associated or blended with crude petroleum oil at the time of production, or (b) which produces more than one hundred thousand (100,000) cubic feet of natural gas to each barrel of crude petroleum oil from the same producing horizon, or (c) which produces natural gas from a formation or producing horizon productive of gas only encountered in a well bore through which crude petroleum oil is also produced through the inside of another string of casing. (e) The term "oil well" is any well which produces one (1) barrel or more of crude petroleum oil to each one hundred thousand (100,000) cubic feet of natural gas. In the state of Louisiana, the same general result is achieved largely by the following paragraph :* Wells producing both oil and gas shall not waste or blow into the air an amount of gas of more value at three cents per thousand cubic feet, than the market value of the oil recovered. The Commissioner of Conservation shall allow a reasonable time to determine the status of any well. This means that for wells making both oil and gas, if n represents the price of oil in dollars, and x the allowable gas waste expressed in M cu. ft. Per day,

Jan 1, 1938

By R A. Stevenson

The purpose of this paper is to outline a recent development in ground fault protection. The paper deals with the A problems of both grounded and ungrounded systems, with regard to hazards to personnel and equipment, and shows that the increased sensitivity and speed of operation of this new detector results in increased safety to personnel and reduced stresses on equipment, and permits the detection of leakage currents before they become serious faults. The detector can be applied to all distribution systems, either A.C. or D.C., up to 15 kv., and the detector itself can be tested at regular intervals without interrupting line circuits. T HERE is always controversy among engineers as to whether distribution systems should be grounded or ungrounded. There are many experi-enced engineers on both sides of this controversy, and each have valid reasons for their choice

Jan 1, 1964

By W. F. Cloud

The data and information compiled under Part I of this report are the results of experiments performed in the petroleum engineering laboratory under the supervision of W. F. Cloud, Associate Professor of Petroleum Engineering and William Schriever, Professor of Physics, University of Oklahoma. Problems Being Studied Most of the time has been spent in trying to determine the rate of flow and pressure gradient in a 4-in. flow tube 10 ft. long, which was packed with sand of various grain sizes. To date, only two kinds of sand have been packed in this tube: 60 to 80-mesh Canadian river sand, 60 to 80-mesh and 80 to 100-mesh Simpson sand. The original intention was to follow the same procedure and use the same types of crude under identical saturation pressures of both air and gas, as well as unsaturated (dead) oil, flowing the various crudes through several different sizes of both Canadian river and Simpson (Wilcox) sands, but lack of time has prevented such an intensive study of the problem. Some additional time has been spent flowing saturated and unsaturated crudes, similar to those used in the 4-in. tube, through 1-in. tubes, one of which was 2 ft. long and one 5 ft. long. The results obtained have been checked against those obtained by using the 4-in. tube, to obtain the relation of diameter and length of tube to rate of flow in similar sands. Laboratory Equipment Saturation Tank.—A heavy steel cylindrical saturation tank, capacity about 42 gal. was mounted on a platform of bricks, then a galvanized tin temperature bath was built around the saturation tank. This contained

Jan 1, 1930

By D. W. Fuerstenau

The United States is rapidly approaching an acute shortage of minerals. According to some observers, this situation may even be more severe than the energy crisis because the US consumes nearly 30% of the world's mineral production. With the mounting competition for world mineral supplies, we can no longer take for granted that foreign mineral products will be available to the US as abundantly as in the past. In 1973, US consumption of mineral raw materials was $35 billion. Of this, $7 billion consisted of imports. Without a drastic reorientation towards the mining of domestic mineral resources, the 1973 $7 billion deficit might mushroom to $100 billion by the year 2000. Thus, a return to domestic sources of raw materials will become absolutely necessary-and will be bucking the trend of the past 25 years, characterized by capital investment for growth in multinational overseas mining operations.

Jan 11, 1975