Search Documents

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

By N. C. Fick, R. L. Rickett

DESPITE the large volume of literature on alloys of iron and silicon,1 there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carbon and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in, sheet and strip form, the constitution was determined of a series of commercial silicon steels containing 0.05 to o.08 per cent carbon and 0.20 to 4.31 per cent silicon, over the temperature range 1300° to 2500°F. These alloys were all from regular production heats and of commercial quality. The results of, the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented. MATERIAL AND PROCEDURE All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness-the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. [ ] The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired. range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1946

By Russell J. Denny

"A 25m deep cut-off wall is required for environmental remediation of a Former Chlor-Alkali Plant. Extensive trials were conducted to verify the effectiveness of the mixes proposed, with the requirements of the cut-off wall to include limiting criteria for hydraulic permeability, vapour permeability and strength, over a 100 year design life. A limited number of field CSM trial panels were installed on a nearby site with similar stratigraphy, and a variety of mixes and mixing methodologies were used, together with the extraction of deep wet grabbed samples from the panels, which were tested for strength, hydraulic permeability and gas permeability. Test results obtained from these trials revealed a trend which allowed the construction methodology to be decided. Further to this, the mix design needed to be resolved, together with sensitivity analysis on the variations in the mix which might occur during construction, as a result of normal unavoidable variations in construction technique. Laboratory sampling would be used at lesser expense, to resolve the final mix design and analyse the sensitivity of the possible mix variations. An initial series of laboratory mixed samples were prepared using soil samples and groundwater obtained from the site, and testing carried out. However the test results in this initial series of laboratory tests could not match the results which had been achieved in the field trials. Closer scrutiny and investigation and rounds of sampling and testing, then revealed laboratory techniques for mixing and sampling which provided a logical way to match the actual field test results. CSM Construction is due to commence soon and will provide more extensive results which can be compared back to the laboratory trials. This project provides a valuable opportunity to resolve methods of laboratory sampling so that they compare well with results from in-situ deep mixing.INTRODUCTIONThe former chlor-alkali plant at Botany, NSW, which operated from 1945 until 2002, used mercury cell technology and brine solution to manufacture chlorine, caustic soda, hydrochloric acid, sodium hypochlorite and ferric chloride. Mercury contamination is present in the permeable alluvial soil profile beneath the site. The mercury is present in the form of elemental and inorganic mercury, together with dissolved methyl mercury in the groundwater and soil profile beneath the site and also down-gradient of the site, to depths of up to 25m. Residual clay and sandstone bedrock at approximately 25m depth are relatively impermeable and limit the contamination plume. A cap and contain approach has been recommended by consultants Golder Associates, and this involved a subsurface containment wall, or cutoff wall, to restrict groundwater ingress and egress, and lateral subsurface vapour migration. The cut-off wall is situated on the perimeter of the site, with a total length of 430m and passing through alluvial Botany Sands, with a nominal key into the underlying residual clay or sand stone at 20 to 25m depth. An HDPE liner insert was proposed for the upper 7m of wall above the water table, to further limit gas permeability."

Jan 1, 2015

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By R. L. Rickett, N. C. Fick

Despite the large volume of literature on alloys of iron and silicon,' there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carl~on and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in sheet and strip form, the constitution nas determined of a series of commercial silicon steels containing 0.05 to 0.08 per cent carbon and 0.20 to 4.1 per cent silicon, over the temperature range 1300° to 1500°F. These alloys were all from regular production heats and of commercial quality. The results of the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented Material and Procedure All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness—the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1947

By N. C. Fick, R. L. Rickett

Despite the large volume of literature on alloys of iron and silicon,' there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carl~on and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in sheet and strip form, the constitution nas determined of a series of commercial silicon steels containing 0.05 to 0.08 per cent carbon and 0.20 to 4.1 per cent silicon, over the temperature range 1300° to 1500°F. These alloys were all from regular production heats and of commercial quality. The results of the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented Material and Procedure All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness—the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1947

By F. G. Caballero, J. L. Gonzalez-Carrasco, S. Barrius, H. Carreon, M. Lieblich

"The grit blasting is a low-cost technique successfully used to enhance mechanical fixation of the implants through increasing their roughness. As a result of the severe plastic surface deformation, it produces subsurface effects such as grain refinement, hardening and compressive residual stresses which are generally evaluated with destructive techniques. In this research work, non-contacting and contacting thermoelectric power measurements are performed in blasted 316L VM and Ti-6AI-4V specimens using Ah03 and Zr02 particles which yield a coarse and a fine rough surface, respectively. This study correlates the microstructural changes induced by the grit blasting treatment and the limitations and advantages of each of the nondestructive thermoelectric techniques based on the Seebeck effect used to evaluate these biomaterials.IntroductionIt is well known that surface properties play an important role in metallic materials used in bio-medical applications. Since the biological response is correlated directly with surface properties it is comprehensible the intense activity in superficial modification by physics or chemistry methods in this field. Grit blasting, one of the most popular surface modification of metallic biomaterials, enhances the mechanical fixation of the implant through the increase in roughness [1-3]. Roughening is developed by bombarding the surface with a high-velocity jet of ceramic particles, being the final roughness a function of the processing parameters (pressure, distance, time, ... ) and blasting particles (nature, shape, size). As the plastically deformed surface layer tries to expand relatively to the intact interior of the specimen, residual compressive stress gradients develops perpendicular to the surface at shallow depths with a maximum value at a depth in the range of 5 to 60 µm. This surface treatment also may cause subtle variations in the subsurface material properties, such as increased hardness and grain size refinement, which are consequences of the significant plastic deformation through cold work. Blasted affected zones may extend to a depth of up to about 200 µm. The subsurface hardening and the near-surface compressive stress gradient playa beneficial role by retarding fatigue crack nucleation and further growth, ultimately extending the fatigue life of the metallic part [4]. In this work, two non-destructive thermoelectric techniques (NDTT), the non-contacting and contacting thermoelectric power measurements were used to analyze the subsurface induced changes on blasted Ti-6AI-4V and 316L VM specimens using Al2O3 and Zr02 particles. Detailed information on the microstructural induced effects and subsurface mechanical properties were published elsewhere [5-8]. Here the nondestructive evaluation of the involved microstructural changes is used to assess the global subsurface damage. Advantages of using nondestructive techniques during manufacturing are envisaged."

Jan 1, 2012

By Chandramohan P. V., Ravi Kishore

"An underground reservoir was to be constructed at Doha in Qatar. Simsima lime stone is present at the bottom. When the reservoir is empty, there will be uplift at the bottom but this will change to downward load when it is full. The rock at the bottom had high bearing capacity to resist downward load. But uplift had to be resisted by piles or anchors. The reservoir has a size of 120mx80m. Shrinkage and creep of concrete coupled with thermal contraction imposed a horizontal movement of 26mm on the extreme piles. So, piles have to accommodate this as well. This unique situation needed a unique solution. The solution was to provide piles with flexible high tensile strands to take tension. An annular space near the head of the pile would facilitate horizontal movement as well. Compression load was directly passed on to the raft bearing on rock.INTRODUCTIONAn underground reservoir for storage of drinking water was to be constructed at Doha, Qatar. The reservoir was proposed to have a plan size of 120m x 80m. Clear height inside the reservoir was proposed as 17.2m, from the bottom of roof to the top of bottom raft. Overall height of the reservoir at the outlet from the top of the roof to the bottom of raft was to be 21.2m. For the sake of inspection and in order to prevent pollution from the surroundings a gallery was planned around the reservoir. This could accommodate pipelines as well. This gallery was 3.0m wide on three sides and 8.4m wide on the outlet side.The gallery had removable gratings as cover in order to facilitate maintenance. Capacity of the reservoirwas proposed to be 40million gallons. The reservoir is divided into four compartments with baffle walls in each one for water circulation. Roof of the reservoir is kept at 300mm above ground level. There are two levels of car park on top of the reservoir. Top of the reservoir roof is at +14.35. Bottom varies from - 6.68 to -7.08. Lowest water table is at +6.00. Concrete structure of the reservoir was designed by a local consultant. The Navayuga Engineering Company was entrusted with the construction. Please see Figs 1 and 2."

Jan 1, 2017

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By Huai-ying Ma, Jun-hua Zhao, Xia Zhao, Si-bin Zhang, Wen Pan, Zhi-xing Zhao

Ignition is the start point of the sintering circuit, which plays an important role during the whole sintering process. The gas consumption accounts for 80% energy cost in the sintering ignition process. Therefore, gas flow reduction is of great significance to energy conservation in the sintering ignition process. In current study, the concept of comprehensive ignition intensity (CII) was introduced to determine the ignition effect. The experimental results indicate that the value of CII increases with higher air-fuel ratio at gas flow of 550 and 600 Nm3/h. From another point of view, given constant CII value, lower gas flow can be achieved with higher air-fuel ratio. Based on the comprehensive ignition intensity, the ignition parameters were optimized and the gas flow was subsequently reduced. By increasing the air-fuel from 5.5 to 6.6, the gas flow is reduced from 450 Nm3/h (8.1 GJ/h) to around 350 Nm3/h (6.3 GJ/h).

Mar 1, 2018

By C. Coetzee

Additives are commonly used in copper electrowinning to improve cathode morphology. Polysaccharides such as guar are generally favoured as additives due to their compatibility with solvent extraction. Polyacrylamides are, however, being considered as possible alternatives. Understanding the influence of the structural chemistry of additives on electrowinning performance is critical to utilise them efficiently. This paper investigated polyacrylamide additives which are structurally different; their effects on copper electrodeposition were characterized and compared to that of guar. Electrochemical impedance spectroscopy (EIS) were used to characterize the effects of molecular weight and ionic charge of the polyacrylamides on electrodeposition. The findings were compared against results obtained with an industrially used guar product. Equivalent circuit modelling of EIS data indicated that an increase in polyacrylamide concentration and a decrease in additive molecular weight increased the overall system resistance.

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022

By Q. P. Campbell

Activated carbons used in the precious metals extraction industry are characterized by large internal surface areas and a great affinity for metal ions. The purpose of this research is to prepare activated carbon from a South African bituminous coal by physical activation that is suitable and cost-effective for use in the extraction of metals. The quality of the coal-based activated carbon may not prove to be as good as activated carbon produced from other traditional sources, but the production costs involved may make South African coal a feasible alternative feedstock. The activated carbons produced were characterized by Brunauer, Emmett, and Teller (BET) surface area, activated carbon pH, and phenol adsorption studies and the results compared to the results from a commercially available activated carbon, Norit RO 0.8 (control sample). Bituminous coals from various sources including Witbank Seam 4 and Free State coal were used in this study. The preparation method chosen was physical activation using superheated steam. The effects of process variables such as activation time (1-3 h) and temperature (600-800°C) were studied in order to optimize those parameters. The activated carbon surface area was characterized by means of nitrogen adsorption isotherms at 77K. BET surface area analysis showed that Witbank Seam 4 coal activated at a temperature of 800°C and activation time of 3 hours resulted in a surface area of 340 m2/g. Quality control of each sample was performed by measuring the pH of a known amount of the prepared activated carbon in distilled water over time. Results showed that the pH of some of the prepared activated carbons reached a value of 11. Phenol adsorption results for the different activated carbons prepared corresponded well to the results obtained for the Norit RO 0.8 activated carbon sample.

Jan 1, 2012

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

By Roy S. Nutter

An expert system advisor consultant to assist a coal mine section foreman is described in this report. The system is designed for an underground continuous miner section that is being specifically used for longwall development. The system provides three methods of operation that include normal operational mode for use underground, a training mode for use in training section foremen under controlled classroom conditions, and a demonstration mode that is free running. The Face Decision Support System or FDSS, is designed to interface with section environmental monitoring equipment and section production monitoring equipment that may appear in the future. This provides automated reprioritzation of the section foreman's job list from the system. The system 1S written in LASER which is written in C and is operated under the UNIX operating system. The objective of the entire FOSS system is to ensure that no job or piece of information important to safety or to production is forgotten because of the immediate problems confronting the section foreman.

Jan 1, 1988

By M. Vallée

"Geological and technical problems are often considered the most important ones affecting new mining projects. Typical problems and likely causes are reviewed based on current Quality Management and Continuous Improvement (QMCI) perspectives, giving particular attention to the work of W.E. Deming. As the “system approach” is an essential part of these policies, its characteristics are described with particular attention given to cultural- behavioural, organizational and systembased constraints described by J. Gharajedaghi. Given that poor communication and interaction among geologists, mineral processors and mining engineers/operators can seriously affect the adequacy of tests, project planning and execution, and mine profitability, these interrelated processes within the mining systems are analyzed and modelled. The impacts on models and simulations of ignoring typical data, information and knowledge uncertainties are addressed. Adapting W.E. Deming’s Fourteen Points, System of Profound Knowledge and insistence on leadership, and the analysis of mining system constraints, will allow the effective QMCI approach required to reduce geological and technical risks. Whenever we achieve this goal, we will be in a better position to overcome environment-, market-, finance- and community-related problems, achieve higher company and industry profitability as well as more sustained development. RÉSUMÉLes problèmes géologiques et techniques sont souvent considérés les plus importants parmi ceux qui affectent les nouveaux projets miniers. Des problèmes typiques et leur causes sont étudiés dans la perspective de gestion de la qualité et d’amélioration continue (GQAC), en relation avec les travaux de W.E. Deming. Comme l’approche système est au centre de ces méthodes, ses caractéristiques sont décrites en donnant une attention particulière aux contraintes de types culturel-comportemental, organisationnel, et systémique décrites par J. Gharajedaghi. Compte-tenu que les lacunes dans les communications et les interactions entre géologues, minéralurgistes, et ingénieurs/opérateurs miniers peuvent affecter sérieusement la validité des essais, de la planification et de l’exécution des projets ainsi que la rentabilité des exploitations, ces processus connexes font l’objet d’analyse et de modélisation. Les impacts sur les modèles et les simulations de l’incertitude des données, informations et connaissances sont soulignés. En adaptant au système minier les Quatorze Obligations et le Système de connaissance approfondie de W.E. Deming ainsi que l’analyse des trois types de contraintes, nous pourrons développer une approche GQAC permettant de réduire les risques géologiques et techniques des projets miniers et des exploitations. Ceci nous pemettra de mieux faire face aux problèmes reliés à l’environnement, aux marchés, au financement et aux conditions sociales, d’améliorer la rentabilité des exploitations minières et de l’industrie, tout en contribuant de façon accrue au développement durable."

Jan 1, 2003

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general. our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2-by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn ;7± MnO + Fe [A] slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aFPI OFeO ? aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term aFe may he combined with K" to give a new constant K'. Making these changes.

Jan 1, 1942