Search Documents

By Brock Wallis, Steve Davidow

The following text will present the concept of rock socketed drilled shafts used to support electrical substation structures, and discuss the cost and schedule risks that traditional design responses to unforeseen shallow rock can pose to a project. Design considerations will be detailed, including rock characterization, shear strength of drilled shafts, and modeling lateral resistance of the shaft and surrounding rock. The specific case of drilled shafts installed for heavily loaded structures at the Moxie Freedom Substation will provide an example of how close collaboration between the engineer and contractor to refine designs based on site-specific feedback can provide tangible benefits to the project. In this example, value engineered designs resulted in an approximate 40% reduction in shaft/concrete volume and a 60% reduction in total rock socket depth. PROJECT OVERVIEW The Moxie Freedom Project included the construction of a new 500 kV switchyard in Berwick, Pennsylvania. The foundation contractor was selected to install both small and large diameter drilled shaft foundations to support the structures within the switchyard. The small diameter shafts were utilized to support transformers, switches, bus supports and a static mast, while the large diameter shafts were used to support one 180-foot monopole and six H-Frame structures. CHALLENGES: ROCK SOCKETED DRILLED SHAFTS Available geotechnical data at the time of bid included limited borings and seismic refraction. The borings were not located at every structure, and the contractor and design engineer were left to interpret desktop studies and geophysics to determine the probable site-specific conditions at each foundation. The data suggested substantial variability in the quality and depth to bedrock across the project area, indicating significant risk of deep embedment into bedrock at all seven large diameter shaft locations. Rock socketed drilled shafts pose unique challenges for both designers and contractors, and the topic has become a focus of national foundation organizations. Traditional design models result in deeper and/or larger diameter shafts where rock is encountered. In the case where site-specific geotechnical conditions are not clearly understood and rock is encountered at shallow depths, this can lead to significant additional rock drilling, impacting overall project cost and schedule. Rock drilling can result in more than ten times the cost of soil drilling and can easily take in excess of ten times longer to excavate.

Jan 1, 2018

By R. P. Fischer

The Colorado Plateau region has been the principal domestic source of uranium, vanadium, and radium. The value of these commodities produced from the region through 1964 slightly exceeds $2 billion. Most of the deposits occur in streamlaid lenses of sandstone in the Chinle and Morrison Formations. The ore minerals below the zone of oxidation are low-valent oxides and silicates of uranium and vanadium; all of these, except the quite stable vanadium silicates, oxidize readily to a variety of high-valent uranium and vanadium minerals. The ore minerals partly replace fossil wood but mainly impregnate sandstone, typically forming tabular ore bodies that are nearly concordant to the bedding of the host rock. The deposits range in size from those containing only a few tons of ore to those containing more than 1 million tons. Stratigraphic, lithologic, and sedimentary structural factors obviously influenced the localization of these deposits, but igneous activity, hydrothermal mineralization, and tectonic structures show no similarly consistent influence on localization. The deposits are epigenetic, but the source of the ore metals, the nature of the ore-bearing solutions, and the time of ore emplacement are uncertain. A few uranium deposits in the region are dominantly discordant to bedding and occur in collapsed breccia pipes or along linear fractures. Their origins are also uncertain.

Jan 1, 1968

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

Although these subterranean cavities are common to the Broken Hill big lode, yet the Broken Hill Proprietary is the most prolific in their occurrence, loud they have been found of various dimensions almost from the surface down to the lowest levels yet attained in that mine. Many of these vugbs have contined valuable silver, copper and lead deposits, and some have been remarkable for the beautiful forms of crystallization pendant from the roofs and walls, and collected on the floors. The question arises, How are these caverns and fissures in the ore body formed? There are numerous theories more or less feasible, but that the causes are variant is demonstrated beyond doubt. That water in its passage leaving channels, is one ofthe chief factors for their production is assured, and their presence is likewise due to the shrinkage and dropping of the earth from varions causes, to the deposition of material forming ledges overhanging, and thus leaving spaces below, and also to chemical erosion and electrical action both of which latter are constantly at work in reconstructing, segregating and dissolving tlie mineral and metallic constituents of all ore bodies.One of the most remarkable vughs yet discovered in the big mine was that opened up about three months bitek in the' heart of the ironstone body on Block 11, and located about 40 feet below the 100 feet level of Weatherley's stopes, but now destroyed in the progress of work. Probably it was caused by chemical action, the eating out, so to speak, of a soft and soluble portion of the manganic iron, leaving a,hollow about 15 feet long, with a width and height, of say, 6 feet, carpeted with beautiful zinc with a modicum of limeincrustations, apparently produced by the percolation from around the carbonate waters holding these minerals in solution. This cavern was divided into, what might be termed, a double chamber, by big boulders of manganic iron, also coated with an aggregation of small crystals of zinc and lime although the actual proportion of the latter was not determined.

[New York Holds monthly meetings, except June, July and August. J. E. SPURR, Chairman A D. BROKAW, Vice-chairman SIDNEY ROLLE, Vice-chairman M. H. MERRISS, Secretary-treasurer, Nichols Copper Co., 25 Broad St., New York M. F. CHASE KARL HOFFMAN Boston Meets first Monday of each winter month. C. R. HAYWARD. Chairman E. C. GEITHER, Vice-chairman D. H. MCLAUGHLIN, Secretary-treasurer Rotch Bldg., Harvard Univ. Cambridge. Mass. GEO. H. GILMAN GEO. A. PACKARD]

Jan 1, 1928

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By S L. Birch, M D. Raven

X-ray diffraction (XRD) is a well-recognised, invaluable tool to provide detailed mineralogical analysis on a wide range of applications. However, despite the wide use of XRD in many industries, there are currently few recognised standard methods for quantitative XRD analysis and none for the analysis of iron ore materials. An initial step towards preparing a standard method for XRD analysis of iron ores was to assess the current level of precision achievable by practitioners of the technique by organising an international round robin. Six Australian chemically certified iron ore reference materials were distributed to over 100 international participants. A summary of over 120 data sets from more than 80 participants is presented. Results show that a bewildering array of techniques for sample preparation, data collection, phase identification and quantification were used. The reported values for the main components (ie hematite, goethite, quartz and amorphous content) show not only extensive variability between participants but also within participants’ results for those who submitted multiple data sets. The disappointing low level of precision exhibited for a relatively simple mineral phase system indicates a strong requirement for development of a standardised procedure.CITATION:Raven, M D and Birch, S L, 2017. Summary of results of an international X-ray diffraction round robin for mineralogical analysis of iron ores, in Proceedings Iron Ore 2017, pp 599–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992

By Omid Marzoughi

In this research, both the kinetics and the mechanisms of the roasting of a sphalerite concentrate from the Bafgh mining complex in Iran were investigated. The oxidation process was performed in a muffle furnace in air and the effects of time and temperature on the degree of oxidation of the zinc sulfide sample were quantitatively studied. The experimental data were fitted to the shrinking core model. In the temperature range of 650–800 °C, the rate-controlling step was the chemical reaction between the zinc sulfide and oxygen with an activation energy of 103 kJ mol−1. On the other hand, in the temperature range of 850–950 °C, the rate-controlling step was oxygen diffusion with an activation energy of 50 kJ mol−1. Also, the roasting process was studied using thermogravimetric (TGA) and derivative thermogravimetric (DTGA) techniques.

By K. P. Anderko

INVESTIGATIONS of the constitution of the system Mg-Ba were first made by Grube and Dietrich1 between 0 and 47 atomic pct Ba and then by Klemm and Dincke1acker" ver the whole composition range. Klemm and Dinckelacker corroborated intermediate phases of the approximate formulas Mg9Ba and Mg4Ba, and showed a third compound to have the formula Mg2Ba, rather than Mg5Ba, as suggested by Grube and Dietrich. Mg2Ba had been previously recognized by Hellner and Laves3 s a MgZn2 (C14) type structure. The main discrepancies between the results of Grube and Dietrich and those of Klemm and Dinckelacker exist, however, in the liquidus temperatures and solidification equilibria of alloys containing more than about 10 atomic pct Ba. The liquidus temperatures measured by Grube and Dietrich, and the outline of the liquidus of Klemm and Dinckelacker are plotted in Fig. 1 on an enlarged scale. Although there are strong reasons to prefer the results of Klemm and Dinckelacker, it was considered worthwhile to remeasure liquidus temperatures of some alloys in the controversial composition range. The alloys, made up from sublimed magnesium and 99.5 wt pct pure barium, were melted in an Armco-iron crucible in a dynamic argon atmosphere. Thermal analyses were taken using a Speedomax auto- matic recorder. Careful stirring during the solidification process was required in order to avoid segregation. After thermal analysis some of the cast alloys were chemically analyzed. The intended and analyzed compositions of the ten alloys prepared are listed in Table I. Since standard barium determinations cannot differentiate between barium present as element and as oxide, both the barium and magnesium contents of the alloys were analyzed. The fact that the sum of barium and magnesium was close to 100 pct in each case was taken as evidence that no excessive oxidation had occurred. The liquidus temperatures measured are listed in Table I and plotted in Fig. 1. As can be seen, they are in good agreement with the liquidus found by Klemm and Dinckelacker. This leaves no doubt that the thermal results of Grube and Dietrich above 10 atomic pct Ba are incorrect. This work was performed under the sponsorship of the Pitman-Dunn Laboratories of Frankford Arsenal, Philadelphia, Contract No. DA-11-022-ORD-1975. Sponsorship and permission to publish by this organization are gratefully acknowledged.

Jan 1, 1958

By T. J. McKeon

Partition curves are used to evaluate the separation performance of gravity-based concentrators. The partition curve is used to identify the nominal density cutpoint and relative sharpness of the separation. In addition, the graphical representation makes it possible to quickly identify the root cause of misplacement based on the characteristic shape of the partition curve. Partition curves have been traditionally constructed using data obtained from float-sink tests using heavy organic liquids. These toxic liquids are environmentally unfriendly and have been banned in several countries. Another method of establishing the partition curve is to introduce density tracers into the feed and plot the distribution to the lights and heavies. For heavy mineral separations, this approach is generally impractical due to the fine particle size. In addition, the partition data obtained using these existing techniques do not account for secondary factors such as particle shape that may influence the separation. In light of these problems, a methodology was developed for constructing partition curves using experimental data obtained from microscopic grain-counts. This technique, which essentially uses the different mineral species as density tracers, provides a powerful tool for evaluating heavy mineral separations. A case study is provided to demonstrate how this analytical approach can be used to assess and improve the separaton performance in an industrial upgrade plant.

Jan 1, 2005

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By D Willis, A Shanahan, C Jacobs, T Luxner

The application of tunnel boring machines (TBM) for reef mining is a unique practice with benefits over current mining methods given the right geology and geometry of the orebody. The Stillwater Mining Company (SMC) of Nye, Montana, USA operates two mines for obtaining platinum metals. The operation is currently using a 5.5 m diameter open-type machine for further mine development, as well as another TBM that they own.The latest 7.1 km bored tunnel, known as the Blitz Tunnel, will be routed parallel to the ore deposit in igneous mafic intrusive rock, and will be used for the life of the mine operation. It will be used to map the ore deposit, and provide a rail haulage route.Detecting the reef in relation to the TBM requires careful analysis. Diamond core drilling occurs ahead, above, and alongside the machine at every 150 m. The core is drilled, logged, and interpreted on the spot, concurrent with boring. Based on the data, the TBM is readjusted so that it stays on the correct bore path.This paper will highlight the application and benefits of TBM usage for reef mining, with detailed descriptions from the mine site.CITATION:Willis, D, Jacobs, C, Luxner, T and Shanahan, A, 2014. Tunnel boring machine usage speeds up development at Stillwater Mine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 683–690 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Robert L. Fleischer

A well known but unexplained experimental fact is the observation1 that aluminum shows a pure <111> wire texture, in contrast with other fcc metals, which have a mixed <100> <111> texture at moderate reductions. A possibly related single crystal observation on aluminum is the following:2 under tensile deformation <111> single crystals are stable (maintain their original axial orientation), while <100> crystals are unstable at room temperature and become stable at lower temperatures. This suggests that at room temperature, as proposed by Yen and Hibbard,3 the single <111> texture obtains be- cause <100> orientations are unstable in the poly-crystal. It also implies that for wire drawing at lower temperature a <100> component of the texture might be expected since that orientation is then stable. This possibility has been examined by wire drawing at temperatures near 77°K. The apparatus was designed to be used with an existing draw-bench, a steel trough acting as die holder and containing sufficient liquid nitrogen to immerse the wire entering the die. The trough is insulated by a styrofoam container to prevent excessive boiling of the bath. The wire emerging from the die enters a polyethylene tube, into the far end of which the grips are inserted. Liquid nitrogen is funneled into the tube to maintain the low tem-

Jan 1, 1962

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By Bingyi Bai, Lifeng Yang, Yanling Guo, Jieyu Zhang, Guoding Gao

In terms of special resources with iron, niobium and rare earth coexisting in Baiyuneboite, the new smelting technology of ferrocolumbite was studied. Reduction experients for the Baiyuneboite and explores ore phase change of Baiyuneboite in the process of reduction was conducted with graphitic carbon as the main reducer and a temperature below 1000 ℃. Moreover, it studies the influence of reducer, roasting temperature and grind fineness on the reduction as well as focuses on the evolution course of iron phase. Through the analysis on in-situ XRD of the raw ore and carbon addition ore, it also develops microstructure change rules of Fe ore phase and ore phase of paragenetic elements for composite ore(Ca, Si, Nb, F) in the process of reduction roasting. In addition, the impacts of temperature on the reduction process are also discussed. With regard to minerals of different particle sizes, the thesis will explore their ore phase changes and microstructures after 10 hours’ reduction under 900 ℃.

Jan 1, 2015

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 &apos;and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960

By Thomas E. Popplewell

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing the mining and treatment methods and costs obtained in sand and gravel plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d&apos;Alene mining region, Shoshone County, Idaho. Production and other statistics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d&apos;Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from Lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964