Search Documents

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

U.S. demand for building and construction materials, such as construction aggregate, gypsum, and cement, remained strong in 1989. Cement imports declined slightly, representing about 17% of apparent consumption compared with 19% in 1988. Mexico, supplying 29% of the total, was the primary source of imports, followed by Canada with 21 %, Japan with 14%, and Spain and Greece with 10% each. Mexico was also the target of an antidumping petition, filed by producers in Arizona, Florida, New Mexico, and Texas, alleging that Mexican cement was being sold in these areas at less than fair value. This was the second petition filed against Mexico in the last 3 years. The International Trade Commission made a preliminary determination that the cement industry in these regions was materially injured by Mexican imports. U.S. demand improved for construction aggregate for the fourth consecutive year and was at a near-record level. The U.S. gypsum industry performed well, even though new housing starts decreased for the third consecutive year. Increased U.S. exports of gypsum wallboard and strength in the remodeling markets offset the impact of declining housing starts.

Jan 1, 1990

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By R. E. Grace

WHEN an Fe-C alloy, partially reacted to pearl-ite, is quenched rapidly enough to suddenly stop the growth process, it may be expected that any carbon concentration gradients will freeze in situ in the newly formed martensite. A short tempering treatment should precipitate finely dispersed iron carbide particles in approximately the same distribution in which carbon existed during the growth process. Examination with the electron microscope of areas of tempered martensite adjacent to the pearlite-martensite interface should reveal the existence of preferred areas of precipitation. Fig. 1 is an example of an electron micrograph used in this study. Small sections of a commercial steel (0.9 pct C, 1.6 pct Mn, 0.25 pct Si) were austenitized at 945°C in air for 45 min, furnace-cooled to 697°C, iso-thermally reacted to pearlite for 30 min, and quenched into iced brine. Two samples were tempered 5 and 20 min, respectively, in air at 498°C and were subsequently quenched in water. The samples were mechanically polished and etched in 1 pct picral. Collodion replicas were made by the conventional technique; these were shadowed with chromium at about 650' from the horizontal, and electron micrographs were taken at a linear magnification of 14,200X. Prints were made at a magnification of 44,100X. Lineal analysis of the prints was made as a function of the interlamellar spacing and volume percent of iron carbide. Straight lines were drawn into tempered martensite between adjacent lamellae at a distance S/4 or S/6 apart, where S is defined as the interlamellar spacing measured at the pearlite-martensite interface. The volume percent of iron carbide was measured along each of these traces with a "gage length" of S/10. The results of analyses of two samples are shown in Table I. The area included between the S/2 and S distance from the interface could be considered homogeneous within the sensitivity of the measuring technique. This value was used as a proportionality factor to evaluate an arbitrary carbon content of homogeneous austenite, and also as a parameter by which error in measurements could be evaluated. Results of the lineal analysis are shown in Figs. 2 and 3. Fig. 4 shows the statistical nature of the interlamellar spacing for all lamellae measured in this

Jan 1, 1954

By He De-wen

Based on the principle of life cycle assessment (LCA), municipal solid waste management (MSWM) was analyzed by life cycle inventory method. According to the system expansion and substitution method, the content and frame of life cycle analysis is summarized and applied to municipal solid waste. On the basic of feasibility research of life cycle analysis on MSWM, the paper put forwards complete and concrete ?three changes? measures under life cycle analysis on MSWM. Some aims of MSWM can be achieved under above conditions of LCA on MSWM: to improve the current system efficiency of MSWM; to enhance the serve quality of MSWM, to increase recycle garbage from MSW; to reduce waste amount and reach minimization and innocuity aim of MSWM; to help the departments of MSWM to get over all difficulties to realize their ideal goals.

Jan 1, 2009

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By C. T. Aimone-Martin, V. L. Rosenhaim

The response of two structures to blast-induced ground vibrations were evaluated and compared in order to quantify the impact of different blasting operations, hard rock and soft rock blasting, upon the structures movements. The first instrumented structure was a residential type, located in the operational area of a coal mine, were blasting is conducted in soft rocks, such as siltstone and coal, with compressive strength ranging from 20 to 50 MPa. Blasting is characterized by low benches, with hole lengths averaging 5.5 m (18 ft) and low powder factors, 140 to 210 g/m3 (0.236 to 0.354 lb/yd3), resulting in very little horizontal movement of the rock during the blast. The second structure was a commercial building, located in a basalt quarry (compressive strength between 109 and 180 MPa), where blasting is conducted in 12 m (39.4 ft) benches with powder factors ranging from 200 to 350 g/m3 (0.337 to 0.590 lb/yd3). Velocity sensors were placed on the structure walls to measure wall displacements and calculate blast-induced strains in the walls, and these results were compared with the driving ground excitations. The calculated strains were compared with the limits of rupture of the cement grout used as mortar between bricks and as wall coating, considered to be the weakest material in the structure composition. The blast-induced response of existing cracks in the structures were also measured using displacement gages and compared to the daily influence of weather fluctuations, such as changes in temperature and humidity, on crack movement. The results show that for the same levels of ground motions the structures present different movement, resulting in distinct levels of induced strains on the walls depending on the geology. The influence of long-term temperature and humidity variations on crack movements on both structures is very similar, during the same seasons of the year. Crack response to long-term weather changes is 2.5 to 3.5 times greater than blast influences.

Jan 1, 2015

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By Jarc H

The steeply dipping silver/lead/zinc orebodies at Mount Isa mine have been extracted most recently by a combination of cut-and-fill and open stoping methods. Bench stoping was first used at Mount Isa Mine seven years ago to allow safe extraction of a highly stressed cut-and-fill stope. Subsequent benches have shown that the method offers significant cost and safety benefits through increased productivity and reduction in man exposure. The success of benching has lead to cut-and-fill mining being replaced at Mount Isa.Significant resources have been focussed to optimise benching. This paper describes the operational, planning, and research and development aspects which have contributed to the method to date. A brief look is also taken at the future direction of benching at Mount Isa.

Jan 1, 1992

By P. S. Haury

"INTRODUCTION Preliminary examinations of the Mohawk zinc prospect were made by John 14. Price and the author in July, August, and September 1943. Considerable quantities of oxidized lead and zinc minerals were found in old shallow work¬ings along two faults - one an over thrust fault with Paleozoic limestone in the hanging wall overlying Cretaceous shale and arkose in the footwall of the fault, and the other a bedding fault in the Paleozoic limestone.The chances appeared good for finding important lead-zinc sulfide ore bodies at 200 to 300 feet beneath the surface, so exploration in three steps by the Bureau was recommended:Surveying, mapping, and character sampling of the outcrops with topographic and geologic mapping of the immediately surrounding area.Preliminary drilling of four test holes, aggregating about 1,500 feet, to locate the top of a possible sulfide ore zone and determine the thickness and intensity of the sulfide mineralization.Contingent upon favorable results of the second step, diamond drilling of about 6,300 feet of additional hole to explore the sulfide ore bodies.The outcrops were surveyed and sampled, a topographic map was made of the area, and the geology was mapped. A project was set up for preliminary drilling of step 2 in the fiscal year 1944-45. An access road to the drill sites was built in April 1945. Diamond drilling was started on April 28 and completed on September 25, 1945, under the supervision or the Bureau of Mines. The exploratory work is covered in this report."

Oct 1, 1946

By Fernando Humberto Muge

One of the problems that arises in the early stages of the mine planning before the determination of the mining exploitation method is to predict what will be the recoverable ore reserves in tonnage, grade and metal quantity, if the select ion is based upon block grades. The estimation of these recuperation or recoverable functions can act as an important planning tool in what concerns the appraisal of the consequences of ore-waste discrimination of individual blocks in a selective mining operation. Estimation methods of all these functions are discussed together with cross validation tests using the available information concerning a preliminary drilling campaign accomplished during the exploration stage of an iron orebody located in the North of Portugal (Moncorvo Orebody).

Jan 1, 1982

By J. H. LaVerne Palmer, W. (Bill) C. Cox, Lorant B. Geller

An erector transporter (ET) has been designed and built to lift, carry and erect heavy machinery components, in particular the components of a 7.6 m diameter tunnel boring machine (TBM), within the access tunnels of a submarine coal mine in Eastern Canada. The ET is capable of manoeuvring within a 7.6 m tunnel while precisely positioning components as large as 6 m in diameter and weighing up to 27 tonnes each. The unit can negotiate 20% grades while carrying loads of 30 tonnes. The major design features, verification tests and performance trial results are presented. The versatility of the ET is such that many other applications are possible.

Jan 1, 1985

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

The influence of SiO2 on the reducibility of the CaO–Fe2O3–SiO2 system was fully examined in this study. The isothermal reduction kinetics of CF and CF8S (CaO/Fe2O3 = 1:1, wt% (SiO2) = 8) were investigated through thermogravimetric analysis at 1123, 1173, and 1223 K with 30% CO and 70% N2 gas mixtures. The reduction of the samples with 8% SiO2 was not only highly accelerated but also proceeded easily. Rate analysis revealed that CF and CF8S reduction occurs in two stages, the Fe3O4-to-FeO stage overlaps with the previous Fe2O3-to-Fe3O4 stage and tends to approach the following FeO-to-Fe stage with the addition of SiO2. The apparent activation energy values of CF and CF8S reduction are 46.89 and 8.71 kJ mol−1. Sharp analysis indicated that CF and CF8S reduction was expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction.

Mar 1, 2017

By D. E. Walsh

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No.4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10-20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove grindabilities all appear to change linearly with temperature within the 275" C to 325" C range.

Jan 1, 1997

By Bill Mariucci, Gary Almeraris

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2009