Search Documents

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By I Coombes, M Trim, Y Sun, M McRae, A Spiegl, H Lagger, A Amon, P Barraclough, M Villeneuve

The Brisbane Airport Link Project (AirportlinkM7) includes the design and construction of more than 12.5 km of tunnels, with the Kedron interchange including four ramp tunnels that intersect with mainline tunnels and result in caverns with spans of up to 26 m. These caverns are in highly variable ground conditions with less than 35 m of cover underlying residential neighbourhoods and commercial properties. The Kedron caverns were constructed using the sequential excavation method (SEM). Owing to complex geometry and excavation sequence, the caverns were designed based on numerical modelling methods, including both two- and three-dimensional models. These numerical methods were used to develop a suite of support types with excavation sequences for the expected range of ground conditions. A combination of methods that included in-tunnel monitoring (convergence monitoring and extensometers), probe holes, endoscope probes, face mapping and ground settlement measurements were used to verify performance of the tunnel support systems and to select and refine the appropriate support system for each section of the caverns. The construction monitoring data indicated that numerical modelling can provide a good basis for predicting the performance of large-span underground openings in highly variable ground conditions. This paper presents a comparison of the performance of the caverns predicted by state-of-the-art numerical models and the actual measured performance.CITATION:McRae, M, Villeneuve, M, Trim, M, Sun, Y, Barraclough, P, Spiegl, A, Amon, A, Lagger, H and Coombes, I, 2014. Brisbane Airport Link Project – design and construction of the 26 m span Kedron Caverns: comparing monitoring data with the design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G. Kolosay, J. Rajala, G. Deschênes, A. Romanov

ABSTRACT: The Kupol project, located in Far East Russia, treats a high-grade, free-milling ore containing 25.5 g/t Au, 298.3 g/t Ag, and 0.5% pyrite,with a P70of 53 microns. Most of the gold occurs as elec-trum and the silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite, andproustite. The mill reached the design throughput of 3,000 tpd six months after start-up. AKnelson con-centratorrecovers10.4% gold and 0.5% silver. Leaching (14.5 hours pre-treatment and 116 hours cyanidation)of gravity tailings is performed with the CANMET Enhanced Leach Process (CELP),using only 490 ppm NaCN (cyanide consumption of 1.1 kg/t). The precious metals are recovered by counter-current decantation and the Merrill-Crowe process. Calcium hypochlorite destroyscyanide and thiocyanate. Overall, gold and silver recoveries for 2008 were 95.4% and 85.6%,respectively (2.8% and7.5% higher than targets). In the first eight months of 2009, gold and silver recoveries were 95.0% and82.6%, respectively. By August 2009, the mill processed 1.42 million tons of ore with production of 1.1 million ounces of gold and 11.3 million ounces of silver. CELP performance was not affected by changes in feed grade and ore mineralogy. Additional modifications to the leaching strategy allowed further reduction in cyanide consumption and effluent treatment costs.

Jan 1, 2011

By M. Cowling, S. Kumarl, A. W. Piper, R. A. Forsdick, C. Bailei, M. Patell

"The lead-refining process takes place in hemispherical vessels called kettles. In these kettles, lead-bullion is mixed at a certain temperature to remove impurities from the melt. This paper presents steps in a novel method for calculating vortex shape and flow field in the refining kettle using Computational Fluid Dynamics (CFD). First of all a two-dimensional axisymmetric model is used to calculate the vortex shape at the liquid-air interface. Here action of impellers and baffles are accounted for by adding source and sink terms to the appropriate momentum equations. The model includes Yolume of Fluid (YOF) method to predict the shape of interface deformation, i.e. vortex. This strategy reduces the computationally intensive three-dimensional transient simulations to a more efficient two-dimensional model. The calculated vortex shape is then used to regenerate a full three-dimensional grid. This grid is used to carry out steady-state simulation using the standard multiple-reference-frame method of impeller-fluid-baffle interaction within the commercial code Fluent. Simulation results for both stages of the development are compared with experimental data.IntroductionOne of the most important steps in Lead Refining process is impeller stirred mixing of Lead Bullion in hemispherical vessels. During this process, the melt is treated with one or more reagents in order to remove impurity elements such as copper, antimony, silver and bismuth. These impurities react selectively with the reagents and float to the melt surface in the form of a powdery layer, which is then skimmed for further processing. Figure-! shows (a) the lead refining kettle and (b) the schematic representation of involved flow pattern. Stirring of the lead bath using specific impeller designs, which creates a central vortex, provides a mechanism for draw-down and dispersion of the buoyant reactants. Clearly, effective control of the impeller generated vortex and flow pattern is crucial to achieving efficient operating conditions."

Jan 1, 2001

By Douglas W. Barr

If some of you have been through the long hot summer in the southwest, you may find it refreshing to turn your thoughts to the wintertime problems of mineral processing in the northern climates. The purpose of this paper is to point out some of the ways in which heat is gained or lost in the tailing basin operation and the problems that can result if too much heat is lost.

Jan 1, 1980

Truman H. Aldrich '78 W. S. Ayres '73 Andrew A. Blair '75 Walter M. Brodie '72 H. M. Chance '74 Fred'k G Corning '77 Ralph Crocker '81 A. W. Crookston '80 George M. Davidson '81 W. B. Devereaux '80 H. S. Drinker Founder William E. C. Eustis '76 B. F. Fackenthal, Jr. '80 John Hays Hammond '81 Edward Hart '81 A. Heckscher '79 Henry D. Hibbard '79 Francis C. Holman '81 Julian Kennedy '79 William,St. George Kent '72 Frank Klepetko '80 Wheaton B. Kunhardt '80 Daniel J. Leary '81 Frank Lyman '77 John Markle '79 Samuel Mather '79

Jan 1, 1923

By Kai Nielsen

The paper presents the results of several industrial and laboratory blasting, crushing and grinding tests and experiments investigating how blasting can influence the subsequent crushing and grinding operations. The paper also describes how these results can be used in order to optimize the entire comminution process from solid ore to a semifinished or marketable product. Two cases are presented, one looking at the processing of fine grained taconite ore, and the other discussing the processing of raw milling product for cement burning.

Jan 1, 1998

The 112th Annual National Western Mining Conference (NWMC) hosted by the Colorado Mining Association (CMA) drew some political heavyweights, if by voice only, into the fray of two of the hottest topics that the mining industry is currently facing ? climate change and the new energy economy. A changing political landscape in Colorado, as well as in Washington D.C., has given rise to questions about the economic future of the United States and the mining industry?s role in that future. While there has been a recent push away from traditional energy sources to a ?new energy economy? that is rich in renewable energy sources such as wind and solar, the NWMC?s agenda emphasized the role that minerals will play in new energy technologies. The conference was also full of talks about the industry?s role in reducing the United States? reliance on foreign oil and other mineral commodities. To that end, an impressive lineup of speakers were invited to attend the three-day conference Feb. 8-11, in Denver, CO. Unfortunately, Mother Nature had other plans and three of the four headliners, including Denver?s mayor and Democratic candidate for governor of Colorado, John Hickenlooper, were unable to get to the conference because of a massive blizzard on the East Coast locked them in Washington, D.C. However, with modern technology, a full auditorium heard presentations from Hickenlooper, National Mining Association (NMA) president and chief executive officer Hal Quinn and Glenn Kelly, vice president, government affairs for NMA. Republican candidate for governor of Colorado, Scott McInnis, did speak to the crowd in person.

Jan 4, 2010

By Martin Herrenknecht

Tunnel boring machines continue to develop to take on not only larger and larger diameters but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar has required innovative design approaches. A systems approach has been required to produce tunnelling machines that can not only safely excavate the tunnel but do so in an efficient, cost effective manner that stresses production and labor saving approaches. This paper will review the current design developments and present recent projects where these most recent principles have been applied.

Jan 1, 2008

Bioleaching of E-Wastes

Sep 13, 2010

By Thomas A. Phillips

An economic evaluation of the Bureau of Mines process for the separation of raw urban refuse into its metal, mineral, and energy components is presented. The process recovers ferrous metal, mixed nonferrous metals, aluminum, mixed-color glass cullet, and refuse-derived fuel products from raw refuse. Data for this evaluation were obtained from selected runs at the Bureau's pilot plant in Edmonston, Md. A cost estimate was prepared for a plant capable of processing 1,000 tons per day of raw urban refuse operating two shifts, 6 days per week. The fixed capital cost, based on second quarter 1976 equipment costs, is approximately $14.5 million excluding land and shipping containers. The estimated operating cost is approximately $8 per ton of refuse processed. This does not include credit for the products, transportation of the products, a tipping fee, or a dumping fee for wastes produced. No finance charges or taxes are included in the operating costs.

Jan 1, 1977

By S. Haggarty

"Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Milling capacity is 3,400 SDT /Day with an average feed grade of 0.080 Oz Au/Ton. Gold processing involves three stage grinding including tertiary pebble milling, two stage cyanide leaching and filtering and Merrill-Crowe zinc precipitation.A summary of process improvements required to increase milling capacity above the initial design tonnage of 2, 700 SDT /Day are described -Installation of a 42"" x 65"" Allis Chalmers Gyratory crusher replacing a 42"" x 48"" Traylor jaw crusher.Installation of polyurethane screen panels replacing woven wire cloths on an 8' x 20 ft triple deck screen.Installation of a hopper clarifier to reduce filtrate turbidity.Automated control of solution balancing and effluent treatment circuits.INTRODUCTIONThis paper describes mining and milling practices at the Nickel Plate Mine and details post start-up process modifications which were required to attain design tonnage.Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Mining capacity from the open pit is approximately 32,000 TPD with an average waste/ore ratio of 8.4:1.Milling capacity is 3,400 SOT/Day, above initial design tonnage of 2,700 SOT/Day. Feed grade averages 0.08 Oz Au per ton yielding 85,000 troy ounces of gold per year."

Jan 1, 1991

By S. Vivek

An Atomic force microscope (AFM) was used to measure the surface forces between hydrophobic silica surfaces. The measurements were conducted in the presence and absence of Cu(II)species in solution to study the effects of the cation adsorption on the hydrophobic force. The results obtained in the absence of the Cu (II)species showed that the hydrophobic force does not change with pH, while the electrostatic repulsive force changes substantially with pH. In the presence of the Cu(II) species, the hydrophobic force begins to decrease at a pH where Cu2+ions are hydrolyzed, indicating that the first hydrolysis product (i.e., CuOH+ions) are the species adsorbing on the surface of the hydrophobic silica. The results of the surface force measurements were used to develop a model for the adsorption of the hydrolysis product of Cu(II) species on the hydrophobic silica.

Jan 1, 2003

By David Evans, David Barnes, Robert Raponi

"The Williams Mine processes, on average, 6,450 t/d of gold bearing ore using two parallel grinding circuits, leaching and C.1.P., carbon stripping, electrowinning and refining. At present, each grinding circuit consists of a SAG mill in closed circuit with a spiral classifier and a ball mill in closed circuit with two stages of cyclones.Since grinding has always constituted the largest portion of milling costs, the Williams Mine has been proactive in trying to reduce such costs through innovative changes. One project under consideration is the replacement of one spiral classifier by a vibrating screen.This paper discusses the testwork performed to evaluate the replacement of one spiral classifier by a vibrating screen, and the preliminary engineering performed to date.IntroductionThe Williams Mine, located in northwestern Ontario, approximately 40 kilometres east of Marathon, is part of the Hernia gold camp. The mine is operated by the Williams Operating Corporation and is owned by the Teck Corporation and Homestake Canada Incorporated. Operation of the mine started in October 1985 at a rate of 3,000 t/d. After a mill expansion in August 1988, throughput increased to 6,000 t/d. Production has increased steadily since the mill expansion and in 1995, an average of 6,450 t/d of ore was processed at a recovery of 95.1 %."

Jan 1, 1997

By F. P. Hassani, M. Hefni, M. F. Kermani

"This study is part of large and an ongoing investigation into the development of a light-weight and highly fluid mine fill for various applications in mining and civil operations. Foam mine fill is the new material proposed for backfilling mines, and is fabricated by mixing stable foam into a mixture of tailings, binders, and water. This paper investigates the effects of both binder dosage and the amount of foam used upon the mechanical and physical properties of foam fill, mainly in regards to compressive strength, porosity and density.Samples were prepared using tailings from a copper mine as the inert material, Normal Portland Cement as the main binding agent, and a foaming agent with a foam generator. Samples were cured for 7, 14 and 28 days and were then subjected to unconfined compressive strength (UCS) testing. Select samples were subjected to mercury intrusion porosimetry, so as to study the microstructural properties. An empirical model was then developed, using a response surface methodology to establish a relationship between the investigated parameters. INTRODUCTION AND BACKGROUNDThe disposal of mine tailings is a significant issue in the mining industry, particularly as mine production increases. Many mines re-use mine tailings for backfilling, which is a method for reducing environmental exposure to tailings, maintaining underground stability, and increasing ore recovery (Benzaazoua, Belem & Bussière, 2002).This paper introduces a new type of backfill called ‘foam mine fill’. This proposed backfill material is similar to cellular concrete, as air bubbles are entrained in cement or lime mortar, resulting in a cellular structure (Narayanan & Ramamurthy, 2000). Air voids can occupy up to 70% of the volume of concrete, which makes it light- weight, and thus can be used for a wide range of civil applications, including backfilling (Tarasov et al. 2010; Panesar, 2013). Unlike cellular concrete, the incorporation of air bubbles into a mixture of tailings, binder and water makes foam fill a potential new backfilling material. Furthermore, a preliminary investigation on foam fill samples found that pulp densities should be optimized before adding the foam, in order to produce consistent samples without foam segregation or losses (Hefni et al., 2014)."

Jan 1, 2015

By J. S. Browning

The pegmatites of the Kings Mountain-Lincolnton, N. C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li2O (lithia) as spodumene.1 The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2,3,4,5,6,7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals.

Jan 7, 1961

By K. Wood, R. McIvor, P. Blythe, M. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented.Total mill x Classification x Test specific x Grinding power draw system efficiency grinding rate rate ratio= Production rate of new product size materialExamples from industrial plants and applications in the research and development field are discussed.

Jan 1, 1990

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man's dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives : 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1959