Search Documents

By Peter Grandone

Bureau of Mines engineers engaged in studying stimulative methods of recovering oil have been making a series of tests on the effectiveness' of methods that may be applied in water flooding oil-bearing sandstones. The report gives the test procedures and results of a study of the rates and pressures used for injecting water into several sandstone formations in the Mid-Continent fields for the purpose of learning more about the mechanics and efficiency of the flooding process and to provide useful information for operators of water floods in this area.

Jan 1, 1949

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Yu. V. Ponomarenko, A. I. Meka, P. A. Witherspoon, Yu. I. Volkov, J. E. Gale

"The mining of iron ore in the Kursk Magnetic Anomaly (KMA) region of the U.S.S.R. is done mostly by the open-cut method. An assembly of open pits capable of producing about 100 million tons of ore per year makes KMA the largest iron ore field in the world. Three gigantic open pits are currently in operation: Lebedinsky, Mikhailovsky and Stoilensky. These pits are as large as 13 km2 on the surface and as deep as 230 m. The mining operations are constantly faced with the problem of flooding from aquifers that overlie the orebodies; the magnitude of the problem is evident from the fact that the present groundwater inflow to these three pits is about 110 million mt /yr.Under such conditions, safe operations and pit wall stability are of great importance, and this has been accomplished very effectively by the appropriate use of seepage barriers and drainage systems. At KMA, the most important items used in the system of groundwater control are standard pumping wells, raise wells that drain into a 20 km to 30 km long underground drift located just outside the perimeter of the pit, horizontal wells driven through the pit walls, and horizontal drains. This paper describes the mining and engineering technology that have been developed at KMA to control the groundwater systems and protect the mines from flooding."

Jan 1, 1992

By E. Van Der Lingen, A. Paton

"The South African ferrochrome industry has been faced with various challenges during the past few years, such as influences from the market, manpower strikes, China’s control over the demand for both ferrochrome and chrome ore from South Africa, and electricity supply constraints, placing increased pressure on the local industry to improve output in order to remain globally competitive. The year 2016 brought a dramatic change in the local ferrochrome industry, being marked by higher chrome ore prices and the takeover of some idle smelters.This study investigates the methods of technology acquisition used in various parts of the ferrochrome smelter value chain throughout a business cycle, and whether there is a preference for a specific acquisition in an explicit part of the value chain. The study also considers whether companies prefer to partner with local or global institutions for collaborative development, and the methods used by companies to protect their technologies.IntroductionSouth Africa holds the world’s largest chrome ore reserves and was the world’s largest producer of ferrochrome until 2012, when China became the leading ferrochromeproducing country. South Africa’s chrome ore (chromite) supply into the Chinese market has risen significantly from 36% of China’s total chrome ore imports in 2010 to more than 70% in 2016 (Fowkes, 2014; Creamer, 2017). China controls the demand for both ferrochrome and chrome ore from South Africa (Fowkes, 2014). China’s high import rate of chrome ore has resulted in ferrochrome prices being driven down and a depressed ferrochrome market. The South African industry meets the chrome ore demands but loses out on ferrochrome beneficiation.Furthermore, the local ferrochrome industry has been threatened with the overall poor competitiveness over the past few years, resulting in four of the eight producers ceasing operations at the beginning of 2016. Challenges experienced by the producers, some of which are directly linked to production costs, include influences from the market, productivity that was affected by wildcat strikes, China’s control over the demand for both ferrochrome and chrome ore, and electricity supply issues (Fowkes, 2014, 2013; Biermann, Cromarty, and Dawson, 2012). Ferrochrome production is energy-intensive and South African producers have faced higher electricity costs, electricity supply complications, and a weaker currency exchange rate since 2009."

Oct 1, 2018

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve Engineers. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BIGELOW, BRAXTON. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BROOKS, ALFRED H., Captain, Engineer Officers' Reserve Corps. BROWNE, DE Courser, 1st Lieutenant, Ordnance Dept., Fortress Monroe, Va.

Jan 8, 1917

By K. Liddell

Current practice for the recovery of platinum group metals (PGM) from flotation concentrates is by energy-intensive smelting processes followed by separation and refining of the base and precious metals. Energy costs are rapidly increasing in South Africa and this trend is forecast to continue in future years. Moreover, the smelting operations are highly susceptible to deleterious constituents, particularly chromite; and the increasing tonnages of UG2 chromititic ore being mined results in an increasing chromite content of smelter feeds. Hence there is a substantial incentive to assess and implement alternative processes to smelting for the treatment of PGM concentrates. The Kell process is a patented hydrometallurgical alternative to smelting that is totally insensitive to the chromite content of the feed concentrate and comprises three commercially proven unit operations (pressure oxidation leaching of base metals and sulfur, roasting and chlorination of precious metals). The Kell process provides the opportunity for existing and new PGM producers to significantly reduce their energy consumption, and in particular their consumption of electricity, by removing the need to smelt PGM concentrates. Energy costs, greenhouse gas emissions and installed power requirements are also much reduced. Compared with smelting and refining these reductions are calculated as: ? Total energy consumption-50% reduction ? Electrical energy consumption-84% reduction ? Energy consumption costs-76% reduction ? C02 emissions-70% reduction ? Installed power requirement 92% reduction. The data obtained from simple laboratory batch amenability testing can be readily applied to the Simulus mass and energy balance simulation procedure to determine energy and reagent consumptions, equipment selection and process optimization. The applicability of Kell to treating low-grade 'dirty' concentrates with high UG2 content as well as to polymetallic concentrates containing base metals as the major payable metals with subordinate PGM means that these savings can also be expected when the process is used for treating a range of concentrate types and grades. Keywords PGM,UG2, Merensky, smelting, chromite, electricity, hydrometallurgy, Kell Process, Eskom.

Jan 1, 2011

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By J. H. Kittel

THE properties of the metal molybdenum have been the subject of recent investigations1,2 = which have included studies of the changes that occur in the metal when it is annealed after having been cold worked. Most of the data which have been reported have pertained to only one aspect of annealing, that is, the conditions under which recrys-tallization has been observecl. The process of recovery which may precede recrystallization docs not appear to have been investigated, and it is the purpose of this note to report observations on the recovery process in cold-worked molybdenum as determined by changes ill the thermoelectric power which occur as the metal is annealed. The measurements were made on commercially pure molybdenum wires which, after annealing at 1035°C in dried hydrogen for 1 hr, were swaged to give a series of reductions up to a maximum of 84.5 pct. The variously cold-worked wires were then annea1c.d in dried hydrogen for periods of 16 hr at progrc:ssively highel. temperatures from 200" to 1000 c with a final annealing treatment of 70 hr at. 1100°C. After each annealing treatment the ther.ma1 emf's were determined against a length of original unwo~,ked material that had received the initial hydrogen anrit,aling treatment. The difference in temperature between the hot and cold junctions was maintained at about 75'C. and. the thermal emf's were measured with a potentiometer that could be read. to 0.01 microvolt. Fig. 1 shows the thermoelectric power. (dE/dT) in microvolts per C between annclalcd and cold-worked molybdenum as a function of the degree of cold work. The effect of annealing is shown in Fig. 2. The general shape of the curves in both figures is similar to results which have been obtained for copper." It was observed that after annealing at temperatures as low as 200°C recovery was well under way. The rapid changes irt thermoelectric power observed near 900 C are probably associated with recrystallization, since such a relation has been observed with copper. Beyond 900°C the thermal emf's changed in polarity. indicating that from this point or1 the specimens were more highly annealed than the standard. Annealing treatments could not be given at temperatures higher than 1100°C due to limitations of the furnace, and it is evident that, since equilibrium values of thermoelectric powers were far from having been attained, temperatures considerably higher are required to fully anneal molybdenum. References Robert M. Parke: Molybdenum, A New High-Temperature Material. Metal Progress (1951) 60, pp. 81-96. * R. A. Long, K. C. Dike, and H. R. Bear: Some Properties of High-Purity Sintered Wrought Molybdenum Metal at Temperatures up to 2400 °F. NACA TN 2319 (March 1951): G. W. Brindley: A Thern-io-Electric Study of the Cold-Rolling and Heat-Treatment of Copper, Report of a Conference on the Strength of Solids. Physical Society, London (1948) pp. 95-106.

Jan 1, 1953

By Walter Pajalich

This Bureau of Mines report is a study of the organizational framework of the ferrous scrap industry, of the products produced, and of the factors affecting the consumption of ferrous scrap by the steel industry. Consumption data from 27 major iron and steel firms in the States of Illinois, Indiana, Iowa, Michigan, Minnesota, and Wisconsin during the period between 1957 to 1962 were grouped by type of iron and steel furnace production facilities to determine consumption pattern for various grades of scrap in comparison to ingot production, hot metal consumption, and home scrap generation. Grades of scrap affected by changes in scrap consumption were determined, and the pattern that emerged was analyzed. Correlation of scrap demand and its effects on scrap prices based on price of scrap receipts of No. 1 heavy melting scrap and No. 2 bundles in the Chicago area for the years 1957 through 1962 indicated that demand trends do not always affect the price of scrap, Past and present technological advancements in steelmaking processes are discussed, and their effects on the scrap industry are analyzed.

Jan 1, 1967

By J. D. Kennedy

The alchemists of old are remembered well for their tireless efforts in attempting to convert various common metals, such as lead, into gold. Not so well known generally, but no less intense, have been the efforts of certain individuals who attempted to manufacture diamonds over the last 100 years. Diamond, the most glamorous and permanent of gems and the hardest industrial abrasive, is carbon in a high-density unique crystalline form with a cubic structure and a density of 3.5. This contrasts with graphite at a theoretical density of 2.2 and possessing a hexagonal structure. Diamond is the hardest natural, material known and until very recently had no close competitor, natural or otherwise, with respect to hardness. The hardness of diamond exceeds that of any other industrial abrasive by a factor of approximately five. The early theories of diamond synthesis were rather vague. Since diamonds occurred in nature, man then looked to nature for clues as to how this might be accomplished. The original known diamond deposits of India are alluvial in character and provided little insight as to how diamond had been formed by nature, for in, these locales the diamonds have been washed by streams or carried by the glaciers long distances from the areas in which they occurred originally in the earth's crust. As a matter of fact, we are told that even today the locations of the mother ground for the Indian alluvial deposits are not known.

Jan 1, 1959

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By G Lane, S Morrell

The design of the 12 m diameter SAG mill installed at the Cadia Hill Mine in New South Wales followed after two years of extensive laboratory and pilot plant testwork. The testwork showed the Cadia ores to be hard and competent necessitating the use of both a variable speed SAG mill drive and pebble crushing. The grinding power requirements for the SAG mill was based on engineering in-house grinding software, pilot plant data and simulations using JK SimMet software. Surveys of the SAG mill operation during the first four weeks showed the feed size distribution, transfer size and pebble rate to be lower or less than those for which it was designed. To compensate for the lower pebble rate, the SAG ball load was increased. This resulted in the total comminution circuit power being some 0.5 kWh/t higher than predicted. The JK SimMet SAG model has been modified to take account of these variations.

Jan 1, 2000

By Joe Shoemaker

Automated Spot Generation ? No Operators below the Highwall ? No Operator Wear and Tear ? Reduced Swing Time ? Single and Double Sided Loading ? Minimized Bench Width

Aug 1, 2013

Dr c. J. Fauconnier, Pr. Eng., has a D. Eng. from the University of Pretoria, an M.RA. from the University of Oregon, and an M.Sc. (Eng.) and B.8c. (Min. Eng.) from the University of Pretoria. Dr B. K. Loveday obtained a degree in Chemical Engineering at the University of Natal, where he also obtained a Ph.D. in the kinetics of froth flotation.

Jan 1, 1983

By Andrews Allen

WE all remember when, a few years ago the preparation of coal was nothing but a matter of having somebody at the face or somebody in the railroad car pick out the impurities; also the sizes were generally' made" over a bar screen. Anything that was black was coal; and the only matecia1 picked out was the slate or rock-impurities that could be distinguished by eye or by hefting. This was all right as long. & coal could be sold at. a good price. After all, we are all in business to -make the most money honestly out of a certain acreage of coal and a certain plant. For this purpose what is required is the greatest possible recovery of marketable coal and the highest market price.

Jan 1, 1929

By R. G. Davies

Isothermal annealing of quenched Fe3Al reveals that the superlattice forms by the nucleation and growth of ordered domains. The activation energy for isothermal ordering and initial domain growth is -29 keal per mole, which is thought to he the activation energy for vacancy migration. Domain growth, in the absence of excess vacancies, has an activation energy of -100 keal per mole. A maximum in the hardness is observed when the structure consists Of ordered domains, -35-4 in size, growing into a short-range ordered matrix and, also as a function of degree of order, S, with an infinite domain size at S = 0.4 to 0.5. It is proposed that both maxima are due to a transition from deformation by unit dislocations to deformation by superdislocntions. FE-AL alloys containing more than -23 at. pet Al, when quenched from above the critical temperature for the Fe3A1 type of order, always contain the maximum possible amount of FeAl (B2) type of order' (see Fig. 1). Thus when the Fe3A1 superlattice forms, in a 25 at, pet A1 alloy, it does so from an imperfect FeAl structure. The formation of the Fe3Al superlattice has been the subject of several recent X-ray,1, 2 electrical-resistivity,3"6 and dilatometric3 investigations. McQueen and Kuczynski3 concluded that the isotherma1 ordering of Fe3Al, after quenching from 800°C (T,, the critical temperature for order, is 55O°C), takes place by the nucleation and growth of ordered domains. However, Feder and Cahn4 found that the isothermal ordering was complex but more like a homogeneous nucleation process than a nucleation and growth process. Lawley and Cahn2 reported that the degree of order is a continuous function of temperature which is a characteristic of a homogeneous nucleation process. Thus, the evidence is conflicting as to the nature of the Fe3Al ordering reaction. Lipson7 was the first to suggest that ordered domains should exist in the Fe3A1 structure since, as

Jan 1, 1964

By H. C. Rolseth

The first step in the quarrying of granite, following removal of any overburden material, involves the freeing of large blocks from the formation. For many years the use of explosives was the accepted method of obtaining these blocks. Even today there are operations where this is considered to be the most economical method even though it does result in a high percentage of damaged stone. In more recent times the preferred procedure at most quarries has been to produce a continuous vertical cut or slot completely around the block to be separated. Originally, this was done by drilling a series of closely spaced holes around the block and breaking the web between the holes with a chisel-like tool known as a broaching bar. The machine used in this mechanical method of producing the relief slot is known as the channel bar. The modern day approach to the production of continuous channels was introduced to the industry around 1955 by the Linde Division of Union Carbide Corporation. The method employs a small rocket - jet burner producing a high temperature, high velocity exhaust flame which when directed against the granite causes it to disintegrate. This method, which has come to be known as "Jet Channeling", is now used by practically every major granite producer in the United States and Canada.

Jan 1, 1968

By Alfred E. Schwaneke

An improved maximum-bubble-pressure system using the Sugden twin-capillary method for measuring the surface tension and density of molten metals is described. Improvements include (1) internally ground capillary tips, (2) electronic pressure transducers, (3) micrometer adjustment of immersion depth for density measurements, (4) valuing arrangements to allow operation at other than atmospheric pressure, (5) temperature range to 1,100° C, and (6) recorder readout of pressures. Data for surface tension of mercury from 20° to 300° C are given.

Jan 1, 1970