Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By J. N. Maycock, P. W. M. Jacobs

Previous measurements of the thermoelectric power of ionic crystals are reviewed briefly. It is concluded that, while extensive measurerements are available on systems in which the electrode M has a cation in cornon with the sall MX, there is as yet little modern work on systems in which the metal electrode M' does not haue a calion in common with the salt. We haue now measured the thermoelectric power of- single cryslals of KC1 and of KC1 + SrCl2 between plati.nu?n electrodes over a much wider range of temperature than before. individual ionic heats of transport, which, while probably not very accurate, are of a reasonable order of magnitude, are obtained from this data on the basis of an assumption that charge carriers do not cross the electrode/salt interface. RELATIVELY little work has been done on thermal diffusion in ionic crystals. Reinhold and coworkers1-I measured the thermoelectric power and Soret effect in silver and cuprous salts and their mixed crystals. One electrode was kept at constant temperature and electromotive force was measured as a function of the temperature gradient. This is not a satisfactory technique if the results are to be compared with theory; rather should the electromotive force be measured for small temperature differences as a function of the mean temperature of the two electrodes. They used electrodes having the same cation as the salt. Patrick and Lawsons measured the thermoelectric power of AgBr and of AgBr containing 0.25 mole pct CdBr2 using silver electrodes and temperature gradients of 10°C in the temperature range 100° to 400°C. The results were analyzed using the Teltow9 values of the ratio of the mobility of the two types of charge carrier (cation vacancies and interstitials) found from conductance measurements and the wagnerlo estimate of the heterogeneous contribution to the thermopower, Ohet They obtained values of qi = 0.017 ev and q$ = -0.385 ev for the heats of transport of interstitial Ag ions and cation vacancies, respectively. Their data has been reanalyzed by Haga using the corrections to the Wagner formula for ehet given by Howard andLidiard; Haga found ev. Christy et a1.14 have measured the thermopower of AgBr containing 0.01 to 1.0 mole pct CdBr,. They analyzed their results in terms of the theory of Howard and Lidiard and found that excellent agreement with the theory was obtained if q5 + : + hF was set equal to 0.70 ev at 175°C and equal to 0.58 ev at 250°C. Since Teltow's value for hF, the enthalpy of formation of a Frenkel defect pair, is 1.27 ev, this means that qt + q: increases in magnitude from -0.57 ev at 175°C to -0.69 ev at 250°C. This result is in poor agreement with Patrick and Lawson's value of -0.37 ev for pure AgBr (for which the corrections to the Wagner estimate for ehet are very small). christy1' has also reported thermopower measurements for pure silver halides and for the systems he finds that qr + qt for AgBr increases in magnitude from about -0.55 ev at 150°C to about -1.1 ev at 400°C. The temperature dependence of the sum of the heats of transport in AgCl is very similar in magnitude. The sum qi + q cannot be decomposed into the individual interstitial and vacancy heats of transport without a knowledge of the entropy contribution from the change in the lattice vibrational frequencies around the interstitial and vacancy. Despite this it seems an inescapable conclusion from Christy's analysis that and -6 = Q Ag are quite strongly temperature-de pendent and that -q: is much greater in magnitude than the corresponding activation energy for vacancy migration, +0.37 ev. It remains a mystery as to why the data for pure AgBr are fitted so well by the assumption of temperature-independent heats of transport if association of impurity ions and vacancies is neglected.l The values for q$ and q: so obtained are also much more in line with those expected from a simple kinetic interpretation of the heats of transport due to wirtz.17 Christy and Hsueh have also measured the thermopower of CuCl between copper electrodes; 0 for pure CuCl is comparable with that for the silver halides but, owing to the limited solubility of divalent cation impurities it was not found possible to deduce values for the heats of transport. In contrast to these extensive measurements on cells of the type M MX 1 M, there have been relatively few attempts to measure the thermoelectric power of cells of the form M' 1 MX I M'. (We specifically exclude from discussion cells of this type in which the metal electrodes M' are in contact with gas containing a controlled partial pressure of either M or X,, since in these cells the electrochemical reactions are analogous to those of the first type.) The thermoelectric power of Pb12, PbC12, TlC1, TlBr, TlI, NaNO3, and KNO 3 between platinum electrodes was measured by Thie1e.l3 In discussing these measurements Holtan20 asserts that the thermopotential initially fluctuated wildly and even changed sign before approaching a steady value. A high degree of irreproducibility is also evident in the work of Nikitinskaya and Murin21 who first studied the thermopower of NaCl and KC1 between platinum electrodes. Much better reproduci-bility was achieved in our earlier measurements on KC1;22 these were, however, confined to a relatively narrow temperature range and one of the objects of the work reported in this paper was to extend the temperature range of the measurements of the thermoelectric power 8 of KC1. The only other published

Jan 1, 1967

By R. L. King, J. Cervik, A. A. Campoli

The Bureau of Mines performed laboratory experiments to evaluate the triboelectric effect of particulate-laden gas streams on polyethylene pipe at various velocity, humidity, dust-size, and dust-load conditions. Charges in excess of 10 kV were produced on the outside and inside surfaces of laboratory pipe samples, when exposed to 40 pct relative humidity (RH) gas stream containing coal dust. However, no charges were produced in laboratory tests that duplicated the over 75 pct RH and dust-free gas streams found in working underground pipelines. Bare cop- per wire, which is wound around the polyethylene pipe in a 1-ft (31-cm) spacing and grounded, eliminated the charge on the outside surface of the pipe, but not on the inside of the pipe surface,

Jan 1, 1986

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By J. T. Vehkala, S. S. Kerr, D. E. Robertson

"Since the late 1970s, extensive work has been carried out at Placer Dome Inc. 's Dome Mine to develop new mining methods and equipment to improve the productivity of narrow vein mining (Mining Magazine, Oct. 1986, pp. 308-317; Mar. 1988, pp. 176-/79). This work has been focused on mining veintype deposits varying from 0.9 m to 1.5 m in width using open stoping and cut-and-fill mining methods.In 1989, the Dome Mine entered into a contract with Ram Raising Ltd., a joint venture company of Angus Martin and I.S. Redpath Ltd., to develop and mine a narrow vein test stope using an Alimak Raise Climber. Early results have been favourable, indicating that Alimak methods can be used successfully to mine narrow vein are.HistoryThe Dome Mine, which has been in continuous operation since 1910, is located in South Porcupine, part of the city of Timmins, Ontario. The mine is wholly-owned and operated by Placer Dome Inc. and is part of Placer Dome Inc.'s international stable of of 19 mines."

Jan 1, 1990

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

By N Jeannee, L Rattmann, M W. N Buxton, A deJong, K Nienhaus, A Soares, P Graham, A Korre, J Benndorf, D Buttgereit

The flow of information, and consequently the decision-making along the chain of mining from exploration to beneficiation, typically occurs in a discontinuous fashion over long timespans. In addition, due to the uncertain nature of the knowledge about deposits and the inherent spatial distribution of material characteristics, actual production performance often deviates from expectations. Reconciliation exercises to adjust mineral resource and reserve models and planning assumptions are performed with timely lags of weeks, months or even years.The key concept of real-time mining promotes a change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online data acquired during extraction at the mining face, material handling and processing with a sequentially updatable resource model. This will allow near real-time optimisation of decisions related to long-term planning, short-term sequencing and production control.The proposed framework integrates the following building blocks in a holistic manner: automated sensor-based material characterisationonline machine performance measurementsunderground navigation and positioningunderground mining system simulation and optimisation of planning decisionsupdating techniques for resource/reserve models.This paper introduces the real-time mining concept and the building blocks and provides a review of the state-of-the-art. Technological readiness of necessary building blocks is assessed, and critical gaps for further technology development are identified. The value added is illustrated by means of a case study.CITATION:Benndorf, J, Buxton, M W N, Nienhaus, K, Rattmann, L, Korre, A, Soares, A, deJong, A, Jeannee, N, Graham, P, Buttgereit, D, Gehlen, S, Eijkelkamp, F, Mischo, H, Sandtke, M and Wilsnack, T, 2015. Real-time mining – moving towards continuous process management in mineral resource extraction, in Proceedings Third International Future Mining Conference, pp 37–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

Jan 1, 1966

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By Fathi Habashi

Laboratory autoclaves for hydrometallurgical investigations are available in a variety of sizes, models, and materials of constructions. They vary in sizes from 25 mL to 2 liters for laboratory studies and 5 to 50 gallons for pilot plant work. They are essential tools for studying aqueous oxidation of sulfide concentrates, dissolution of oxide minerals at high temperature and pressure and hydrothermal precipitation reactions. The maximum pressure and temperature at which any pressure vessel can be used will depend upon the design of the vessel and the materials used in its construction. Since all materials lose strength at elevated temperatures, any pressure rating must be stated in terms of the temperature at which it applies. A review of existing models and their accessories will be given.

Jan 1, 2000

Reynolds Metals Company announced plans to increase its rate of production of primary aluminum by 17 thousand tons per year by the end of February. Other producers were expected to increase operating rates during the first quarter of 1976 (see table 10 pg. 29). CHROMIUM -Under the Trade Act of 1974, a petition was filed July 16, 1975, with the U.S. International Trade Commission (ITC) by the Tool and Stainless Steel Industry Committee for Import Relief and the United Steelworkers of America, AFL-CIO, for import relief for certain stainless and alloy tool steel products. The Commission determined on January 16, 1976, in a report to the President, that increased quantities of imports of stainless steel sheet and strip, plate, bar, and rod and alloy tool steel except ingots, blooms, billets, slabs, and sheet bars were a substantial cause of serious injury or threat thereof. The Commission recommended import quotas for the period 1976 through 1980. The President has 2 months in which to act, with his decision subject to a Congressional override.

Jan 1, 1976

By L D. Redden, M G. Nelson

Mechanical flotation machine design is typically based on hydrodynamic analysis, with scale-up calculated by geometric proportionality. End users often specify and purchase machines on the basis of retention time, characterised by the æ$/m3Æ approach; they may also consider the manufacturerÆs installed base. In some applications, end users also consider specific energy and the impact of energy consumption on operational costs. In other cases, a decision may be based on machine type (forced-air versus self-aspirating) and perceived metallurgical or operational advantages of one machine type over the other. With regard to metallurgical performance efficient bubble-particle contact is very important and is primarily influenced by two factors:the concentration and size distribution of bubbles in the machineÆs contact zone (the volume enclosed by the disperser); and the number of times that slurry is pumped through the contact zone. The second factor is a function of the machineÆs pumping rate and its retention time. Field data show that pumping efficiency is independent of aeration rate. In this paper, a new dimensionless number for the characterisation of flotation efficiency is presented. The contact frequency number (CFN) is defined as the number of times a given volume of slurry passes through a machineÆs active contact region, and is given by: CFN Qp/Qf, where:Qpis the pumping rate through the contact regionQfis the volumetric feed rate to the machine

Jan 1, 2005

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By J. Bruce Gemmell

ODP Leg 158 drilled seventeen holes into the active TAG hydrothermal mound and underlying stockwork, 26°N, Mid-Atlantic Ridge. Drilling in five different areas, including a high-temperature black smoker complex and a lower-temperature white smoker vent field, revealed the multi-stage depositional history and character of sub-seafloor mineralization and alteration. The upper portion of the mound consist of massive pyrite and pyrite breccias which are underlain by pyrite-anhydrite breccias and then by quartz-pyrite breccias. Quartz-pyrite breccias grade down into silicified wallrock breccias. Chloritised basalt breccias occur at depths greater than 100 m. Several stages of quartz-pyrite±chalcopyrite veins occur in the stockwork zone and lower portions of the mound, whereas anhydrite±pyrite±chalcopyrite veins occur within the upper parts of the mound. Recovery of unaltered basalt near the edges of the mound has constrained the extent of the stockwork zone to a pipe-like feature 80 meters in diameter. A detailed sulfur isotope investigation of sulfides and sulfates within mound and the underlying stockwork zone has revealed the overall range of sulfide d34S analyses to be 0.35% to 10.27%. Anhydrite has a tight range of d34S values 20.55% to 21.56%. There are distinct differences in d34S values between the different textural types of pyrite (massive sulfide, breccia clasts, disseminations associated with alteration, and veins). The massive sulfide and breccia clasts have a similar distribution of d34S values (6%-8%), however the d34S values of the disseminated pyrite associated with the alteration are distinctly heavier (8%-10%). Vein sulfides have the lightest d34S values (5%-7%). Sulphur-isotope values at TAG are, in general, the heaviest reported for unsedimented mid-ocean ridge deposits.

Jan 1, 1998

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019