Search Documents

By Tetsuji Hirato, A. J. Monhemius, Yasuhiro Awakura, G. W. Warren, E. Peters

An electrostatic pseudo-liquid membrane technique, in which extraction and stripping take place simultaneously in a single reaction vessel using an electrostatic dispersion, was applied to recover Ni(II) from aqueous 0.1 kg m-3 Ni(II)(as NiSO4) – CH3COONa solutions, and the Ni(II) ions were concentrated by a factor of 9 into an aqueous 1.0 kmol m-3 HCI solution using D2EHPA as an extractant at the applied voltage of 3.7 kV for the dispersion. When the process of ESPLIM proceeds favorably, the concentration of Ni(II) in the upper part of the organic phase of the reaction vessel is lower than that in the lower part. In addition, the concentration of Ni(II) in the organic phase of the extraction chamber is higher than that in the stripping chamber. For the stable operation of this process, the stripping rate must be greater than the extraction rate to prevent the excess accumulation of Ni(II) in the organic phase which leads to the poor dispersion of the aqueous phase.

Jan 1, 1993

By J. G. Bruwer

Paper written on project work carried out in partial fulfilment of B Eng Met Surface coatings persisting on zircon particles, after being leached in an acidic solution, are believed to be the cause of zircon misplacement during the electrostatic separation of heavy mineral beach sands. Electrostatic separation is employed to separate non-conductive zircon particles from more conductive rutile particles. Surface coatings on zircon particles are believed to render the non-conductive zircon particles more conductive, resulting in the contamination of the more conductive rutile stream with zircon particles. Resistivity measurements, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were performed to compare the surface characteristics of zircon particles found in the different product streams following electrostatic separation. XPS analysis showed that no significant difference exists in the outermost layer of the zircon particles found in the different streams. SEM analysis showed the existing surface coatings on zircon particles from different product streams to have similar chemical compositions. Resistivity measurements confirmed the results obtained from both the XPS and SEM analysis; no significant differences in the resitivities were observed. From the results obtained it suggests that surface coatings present on zircon particles are unlikely the primary cause of zircon misplacement. Zircon losses can possibly be a result of machine related aspects. Key words: XPS; SEM; resistivity measurements; electrostatic separation; heavy mineral sands.

Jan 1, 2007

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By A. J. Hynes, Lutes. G. G., Ravenelle. J. -F.

"The Anomaly A area of the Clarence Stream gold deposits in southwestern New Brunswick contains mineralized structures that bear geometrical relationships to regional folding events. The four mineralized zones of Anomaly A (AD, MW, 93, and Murphy) are hosted by turbiditic graywacke, quartzose wacke, siltstone, and argillite sequences of the Kendall Mountain Formation. A regional scale structural analysis reflects at least four deformational events, three of which appear to control the folded geometry of Anomaly A (D2, D3, and D4). F2 and F3 folds are coaxial and are refolded into a dome and basin geometry by F4 folds. The mineralized zones are subparallel to axial surfaces of F2 folds. Structural analysis of a mineralized zone exposed at surface indicates that gold mineralization is hosted by a quartz-vein system that comprises veins generated during both D2 and D3. Threedimensional representations of Anomaly A created using drill-core data and ®GoCAD suggest that the quartz-vein system was emplaced in fault structures during D2 as well as within brecciated dilation zones during D3. Three of the four zones that make up Anomaly A have F2 hinge surfaces that can be linked through a geometry compatible with the style of F3 and F4 folds. The apparent continuity of these three zones indicates the potential for kilometer-scale mineralized structures at Anomaly A. Le secteur de l’Anomalie A du gisement aurifère Clarence Stream contient des zones minéralisées qui montrent des relations géométriques avec les épisodes de déformation régionale. Les quatre zones minéralisées de l’Anomalie A (AD, MW, 93, Murphy) sont comprises dans une séquence turbiditique composée de grauwacke, de wacke quartzitique, de siltstone, et d’argilite appartenant à la Formation de Kendall Mountain. Des quatre épisodes de déformation étudiés par l’entremise de cartographie structurale, trois semblent contrôler la géométrie de l’Anomalie A (D2, D3, et D4). Les plis P2 et P3 sont coaxiaux et sont replissés en dômes et bassins par les plis P4. Les zones minéralisées sont subparallèles aux plans axiaux des plis P2. Une analyse structurale effectuée sur une zone minéralisée exposée à la surface indique que la minéralisation aurifère est localisée dans un système de veines de quartz qui contient des veines générées durant D2 et D3. Des représentations en trois-dimensions créées avec le programme informatique ®GoCAD à partir de données de forages suggèrent que le système de veines est localisé dans des zones de failles D2 ainsi que dans des zones de dilatation associées avec D3. Trois des quatre zones qui forment l’Anomalie A possèdent des plans axiaux P2 qui peuvent être liés par l’entremise d’une géométrie qui respecte le style des plis P3 et P4. La continuité apparente de ces trois zones indique qu’une structure minéralisée pourrait s’étendre sur plusieurs kilomètres dans le secteur de l’Anomalie A."

Jan 1, 2008

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By Paul J. Cascone

This paper will discuss the science behind the development of a unique gold alloy for dental prosthetic applications. The alloy (GOLDTECH BIO2000) contains 99.7% gold providing unquestioned biocompatibility and unsurpassed esthetics. The topics discussed are: (1) How the alloy meets the functional requirements of a porcelain-fused-to-metal dental alloy. (2) How the alloy color affects the esthetics of the restoration and why the color of gold is best. (3) Overcoming the intrinsic malleability of gold when grinding the alloy surface. (4) Preventing the oxide color from interfering with the alloy esthetics. (5) Attaining excellent porcelain adhesion. (6) How the design of the restoration allows for the production of single and multiple unit restorations. Gold 2003

Oct 1, 2003

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Barbara Hendrickson

Outline ? Canadian Regulatory Update ? Turning the Corner: Background & Status ? Implications of U.S. Waxman-Markey bill for Canada ? Federal-provincial considerations ? Current certainties and uncertainties ?Turning the Corner? as Originally Proposed ? April 26, 2007 - the Canadian federal government announced Turning the Corner: An Action Plan to Reduce Greenhouse Gases and Air Pollution (?Turning the Corner?)

May 1, 2009

(Published by courtesy of the Great Boulder Pty. Gold Mines, Limited)1. INTRODUCTIONThe faults described in the following paper are of a somewhat unusual character, and have presented a serious problem both in the development and mining of many ore-bodies on the Eastern side of the Boulder Belt. They are mentioned only briefly in the literature of the field, but were observed by, both Stillwell (1)t and Gustafson (2), and have been studied by other geologists and operators in various parts of the "Belt." Their effect on the lodes of Hamilton Section, Great Boulder Mine, was described by King (3) in 1937, and, during recent years, they have been encountered in most of the Great Boulder workings extending east of the Boulder Dyke.Although this paper is based mainly on a study of faulting and development problems on the Great Boulder mine, the general conclusions reached may be applicable to the solution of similar faulting problems in other mines throughout the field.In order to arrive at a clear understanding of the somewhat complicated relationships which the east-dipping faults bear to the lode systems it will be necessary to give a brief outline of the salient geological and structural features of the "Belt" before proceeding to describe the faults themselves.2. GENERAL GEOLOGYThe most recent descriptions of the geology of Kalgoorlie are those by Stillwell (1) and Gustafson (2) and the reader is referred to these as representing the basis of current knowledge of the geology of the field.The Boulder Belt is comprised of a central core of altered quartz dolerite which is flanked on either side by fine grained greenstones and lavas, usually referred to as the calc schists. Down the centre of the quartz dolerite mass there is an infolded bed of slate (2, p. 105) which has been intruded in lit par lit fashion by albite porphyry; the composite body of slate and porphyry so formed is known as the "Boulder Dyke." Numerous smaller porphyry dykes intrude both the quartz dolerite and the calc schist; these vary in composition and range from chloritised hornblende porphyrites to albite porphyries.The whole of the rock assemblage has been subjected tG a considerable amount of folding, faulting, shearing and fracturing, the greater part of which took place before the formation of the lodes.

Jan 1, 1941

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

(Members, are urged -to send in for this column any notes of interest concerning themselves or their fellow-members,). Members and guests R: ho called at Institute headquarters during the period Dec: 10, 1916 to Jan. 10, 1917: F. L. Antisell, Perth Amboy, N. J. William Kelly, Vulcan, Mich. F. J Brulé, Toronto, Ont., Canada. W. H. Lanagan, San Francisco, Cal. Zar T. Crittenden, The. Pas, Mau, Canada. S. Lefevre, Forest Glen, N Y Thomas F. Donnelly, Tucson, Ariz. ' D. A. Lyle, St..David's, Pa. - John Davenport, Brighton, 14 lass. -Domingo Nugués, Buenos Aires, Argon-. E. E. Ellis, Birmingham, Ala. tine. N. H. Emmons, 3d, Copperhill, Tenn. - H. L. Scaife, Clinton, S. C. W.. E. Erdofy, New York, N. Y. Mortimer A. Sears, Washington, D. C. C. L. French, New York, N. Y. E. Spurny, New York, N. Y.' , M. H. Gannon, Butte,. Mont. R. K. Stockwell, Santiago, Chile. R. E. Hoffman, Hannibal, Mo. Benjamin F. Tibby, Salt Lake City, Utah. C. Vey Holman, Rockland, Me. Arthur P. Watt, St. Francois, Mo. Arthur P. Allen has left the employ of the Calumet &- Hecla Mine and is now with the Highland Min. Co., Ashcroft, B. C., Canada. H: C. Bellinger has been appointed. general manager of the Chuqui- - c mata mine-of the Chile Exploration Co. -

Jan 2, 1917

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

The acoustic signals emitted from a laboratory-scale ball mill were used for the estimation of the comminution of two complex sulphide ores, viz. Merensky and UG2 ores from the Bushveld Igneous Complex in South Africa. The digital acoustic signals were transformed to power spectral densities that could be related to particle size distributions (-75 µm to 4000 µm) in the mill by use of continuum regression. This approach is more general than principal component regression methods or Kalman filtering used previously and resulted in significantly more accurate calibration in the case of the Merensky ore, where approximately 93.4% of the variance in the particle size distributions could be explained. With fewer data available, the variance in the particle size distributions in the UG2ore could be explained less accurately (82.4%), but still satisfactorily. In addition, smaller particle sizes (less than 300 µm) could be modelled more accurately in the case of the UG2 ore.

Jan 1, 2000

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008