Search Documents

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By Anand Kumar, Pradeep kumar Jha, Suman Kant, Pradeep Kumar

"It has been a major challenge to reduce the intermixed grade formation during ladle change-over operation in continuous casting process of tundish steelmaking. The F-curve generated by step input of the tracer (new grade steel) tells about the intermixed grade amount for different grade specifications. Use of flow modifiers is beneficial in reducing the intermixed grade because of the change in slope (in different time zones) and position of the F-curve due to their placement at tundish bottom. Present study aims at investigating the role of dam placed before the outlet in a multi-strand tundish with reference to the slope behavior of F-curve in different time zones during the teeming operation plays an important role in determining the intermixed amount.Introduction In Continuous casting process, the old grade steel remaining in the tundish (reservoir between ladle and mould) from the old ladle gets mixed with new grade steel from new ladle and leads to intermixed grade which is considered to be of inferior quality. Although formation of intermixed grade is inevitable with the sequential method of casting, its amount can be controlled by changing the flow behavior of steel inside the steel. Intermixing in a slab caster tundish was simulated using 3-D numerical model based on k-å turbulence equation and compared their result with that of water model experiment Yeh and Hwang [1]. Huang and Thomas [2] reported that quantity of residual fluid in tundish affects the composition distribution in the transitional slab and thus the intermixed length. Huang and Thomas [3] developed three sub models to predict mixing in tundish, liquid core of strand and solidification. Thomas [4] developed a one dimensional model to simulate the final composition distributions in slab caster of continuous casting and investigated the effect of process variables on the intermixing. Alizadeh mehdi et al., [5] simulated of the intermixing phenomenon for slab casting for three different sub models. Goldschmidt et al. [6] developed a numerical model that predicted the location of the intermixed steel in a four line round caster. Lan and Khodadadi [7] studied for the transient fluid flow of liquid steel, heat transfer and solidification during the flying tundish change process. Cho and Kim [8] developed a mixing model to predict the outlet concentration of the tundish during grade transition. Most of the work reported in the literature has dealt with intermixing in slab caster tundish. Billet caster units are more often being used by steel industries due to growing demand of billets. The multiple outlets lead to varying degree of intermixing with time owing to their different distance (location) from the inlet. Use of flow modifier to minimize the intermixed amount, however has also not been discussed in detail so far. Further no work has been reported regarding effect of slope of F-curves obtained through different outlets on intermixing. Hence keeping these objectives in mind attempt has been made by authors to analyze the slope of Fcurves after dividing them into three different time zones and the effect of these time zones on intermixing."

Jan 1, 2012

By Marc Verhaege

The effluent under investigation results from a catalic oxidation unit in which paraxylene is oxydised to terephtalic acid. The solution contains cobalt and manganese as their acetates in a concentration range of 0,4 - 1,2 g/I of cobalt and 0,8 - 2,4 g/l of manganese. Before being fed into the main waste stream treatment unit of the plant it is advisable to apply a petreatment step in which both metals are eliminated to a great extent from this effluent. Conventional treatment is done by precipitation of both metals either through pH increment with a base or by adding a suitable reagent producing insoluble species. The aim of this study was to look for a treatment (elimination of both metal species) in which no sludge or precipitate is formed.

Jan 1, 1995

By Akira Yazawa, Kazuo Koike, Mitsuhisa Hino

"The vapor pressures of MS (PbS, SnS and Sb2S3) in the molten Cu2S-MS, FeS-MS pseudo-binary and Cu2S-FeS-MS ternary systems were measured by means of a transportation method in the temperature range of 1323 and 1423K to calculate MS activities in the sulfide melts. The activities of MS in these systems show negative deviation from ideal behavior except the FeS binary systems which exhibit nearly ideal behavior in the homogeneous melts. The activities of the Cu2S-FeS pseudobinary system, which is fundamentals of the copper matte, were estimated from the activity values in the ternary systems and exhibit negative deviation from ideality.The distribution behavior of tin between the ·matte and silica saturated fayalite slag was investigated under the controlled partial pressures of S02 at l 523K. It was found that, in general, tin is distributed in the both phase, while tin is concentrated to the slag phase with increasing copper content in the matte. The activity coefficient of SnO in the slag was calculated based on the distribution ratio combined with the activity coefficient in the Cu2S-FeS system.IntroductionThe thermodynamic properties related to the Cu2S-FeS system and the Cu2S-FeS-MS systems (where MS can be PbS, SnS, Sb2S3, As2S3, Bi2S3, etc.) is required to be better understanding of the copper smelting process. However, thermodynamic analysis such as the distribution of impurities among the gas, slag and matte phases is difficult due to lack of thermodynamic data. In this study, the vapor pressures of MS (PbS, SnS and Sb2S3) in the Cu2S-MS, FeS-MS. and Cu2S-FeS-MS systems were measured by a transportation method. The distribution behavior of tin between the matte and silica saturated fayalite slag was also investigated. The results in the present experiments are useful to analyze thermodynamically the behavior of component in the copper matte smelting."

Jan 1, 2000

By Yoichi Takeda

Copper solubility in SiO2-CaO-FeOx slag equilibrated with copper matte in 10% SO2 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag, A classical thcrmodynamic model postulating CuO0.5 and CuS0.5 moleculcs assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated SiO2-FeO. binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeO.-SiO2-CaO ternary slag saturated with 2CaOSiO2 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By L. L. Tavlarides, N. V. Deorkar

"Recovery/Recycling of metal ions from industrial process waste streams is a preferred alternative to disposal by conventional techniques. This paper presents methods for preparation of inorganic chemically active adsorbents to be used in fixed bed adsorbers. Methods for immobilization of chelating agents on the inorganic supports are discussed. The prepared adsorbents are characterized to determine coverage density of functional groups, effect of pH on metal ion removal efficiency, regeneration efficiency and uptake capacity. Results from the laboratory scale and bench scale experiments are presented here.IntroductionRemoval of heavy metal ions from processing wastes in various industries is an important problem. Waste streams in electroplating, electronic, catalyst preparation and hydrometallurgical industries contain metal ions such as copper, nickel, chromium, lead, tin, cadmium, silver, gold and platinum. One major concern for the non-ferrous metal industry is secondary recovery of precious metals and cyanide from cyanide leachate from smelter residue and hydrometallurgical waste streams.Recovery methods recently considered include evaporation, electrolyte metal recovery, reverse osmosis (1), adsorption, ion exchange (2,3), membrane separation (4,5) and Solvent extraction. These processes have met with various levels of limited success. The use of liquid ion exchange molecules to selectively extract metal ions for on-site treatment of these waste streams is currently receiving substantial interest (6,7). This interest seems from an awareness of the advances made in the development of commercial extractants for metal ion separation in hydrometallurgical industries (8). However, separation by solvent extraction processes is generally considered to be economical in the range of aqueous metal ion concentrations from 0.01 to 1.0 mol/lit (9). In order to exploit the selectivity of chelating agents, the idea of immobilizing chelating agent into a solid matrix has attracted growing attention in recent years. Many supports such as inorganic oxides, organic polymers, cellulose powder and polyurethane foam can be used for immobilization of chelating agents. Over the last decade, considerable efforts have been directed toward attachment/introduction of chelating agents into a polymer matrix (10,11). Inorganic supports as compared to polymer supports provide high mechanical strength, chemical and thermal stability, and high reaction rates due to open pore structure. On the contrary, organic resins shrink and swell, thus affecting mass transfer (12). Many of the disadvantages of polymer supports can be excluded by the use of inorganic supports. Innovative use of immobilization techniques can produce inorganic chemically active adsorbents with comparable capacity, stability and reaction rates. Consequently, the objective of our program is the development of inorganic chemically active adsorbents to be used in a fixed-bed unit operation as an alternative heavy metal ion recovery process. Methods of preparation of inorganic chemically active adsorbents, (ICAAs) characterization and applications are discussed in this paper. A brief summary of the results from laboratory scale studies and bench scale studies is presented."

Jan 1, 1996

By Lv Guozhi, Niu Liping, Liu Yan, Zhao Qiuyue, He Jicheng, Zhang Ting’an, Dou Zhihe

"This paper proposed a new method of Mg and Cl2 circulating for titanium sponge production by direct pyrolysis and thermal reduction process. Effects of pyrolysis temperature, pyrolysis time and partial pressure of oxygen on pyrolysis efficiency were researched, and the crystallite structural transformation of MgO productions at different pyrolysis temperature and time were analyzed by XRD. The experimental results indicates that the pyrolysis temperature and time effects the pyrolysis efficiency obviously, and the reasonable pyrolysis conditions by using MgCl2 in molten state are as follows: the pyrolysis temperature is 1100?, pyrolysis time is 60min and the partial pressure of oxygen is 100%, the pyrolysis efficiency get above 95% at this conditions. The dynamic analysis of molten magnesium chloride pyrolysis reaction shows that, as a chemical reaction process control, the response of the apparent activation energy Ea=70.4 kJ/mol.IntroductionTitanium is a young metal, it is applied in industrial until the Second World War. It is 160 years from the discovery of titanium to the industrial production of ductility titanium by magnesium reduction method in the United States in 1948. As a new kind of metal, titanium and titanium material are better than the traditional metal materials in mechanical properties, heat resistance and thermal conductivity. Titanium is a kind of landmark structure and function material, which is called “space metal”, “Marine metal”, “Intelligent metal” [1-3]. Although the study of new methods of titanium melting get more at present, Kroll method and Hunter method are really applied to industrial production methods for titanium smelting, and Hunter method is already discontinued because of costs at present. The core technology in Kroll method of sponge titanium production process can be ome down to two circulation, namely the cycle of magnesium and chlorine in preparation-process of titanium sponge. In the traditional Kroll method, the cycle is realized through magnesium chloride which is produced by the electrolytic magnesium reduction process in hot molten state. But because investment of equipment for electrolysis method is too high, this method has not been used by most titanium sponge production enterprise in China. At present most titanium sponge production enterprise in China produce titanium sponge by the outsourcing of titanium tetrachloride, but the main disadvantage of this method is that the by-product of magnesium chloride is difficult to deal with."

Jan 1, 2012

By T. T. Chen

The manganese oxide scales, consisting mainly of MnO2, characteristically occur in banded colloform structures which adhere to porous layers of PbSO4 and PbO2 that oxidized from the rolled Pb-0.7% Ag anodes. Hydrous Mn oxides, Mn3O4 and amorphous Mn oxides are believed to be also present. Tiny particles of gypsum, PbSO4, SrSO4 and AgCl are entrapped in the colloform masses. The gypsum originated from the Zn electrolyte; strontium carbonate was added to the ZnSO4 solution to control Pb, and silver originated from the anodes. Some of the colloform bands contain minor amounts of Pb, implying a limited degree of dissolution of the Pb during electrolysis. Other colloform bands incorporate trace amounts of Zn. Colloform structures permeated with silica gel are presumably caused by the high silica content of the electrolyte.

Jan 1, 2009

By M. Dattilo

Research has been conducted over the past three years using the composite anodes versus the lead alloy anodes. The Merrlin composite anodes have shown the improved performance in copper electrowinning versus the lead-calcium-tin anodes. Using the composite anodes a 100-150 mV reduction in anode overpotential has been observed versus the lead alloy anodes in sulfuric acid electrolyte. The composite coating has excellent corrosion inhibiting properties, and reduces or eliminates the formation of manganese oxide scale. Laboratory evidences indicate that, the use of these composite anodes enhances the process of electrowinning by improving the lead alloy corrosion resistance, lowers the electrode potential, reduces the need for cobalt addition, eliminates the anode cleaning, and reduces the generation of acid mist. Field tests are underway.

Jan 1, 1999

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By Chen L. Lin

Scientific visualization is an ideal methodology for investigating complex phenomena that are characterized by large amounts of data. Furthermore, it is invaluable in the study of processes that evolve in time. Scientific visualization relies heavily on computer graphics, image processing and video technologies. Specific applications of scientific visualization in the minerals and materials processing fields that are considered in this paper include: 1) applied CT technology for multiphase materials and minerals, 2) time averaged density profla in air- sparged hydrocyclone (ASH) flotation and 3) dynamic motion analysis of ball mill grinding.

Jan 1, 1993

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012

By N. Kanari

The kinetics of oxychlorination of MgO by C12+02 was studied in the temperature range of 850 °C - 1025 °C, using thermogravimetric analysis. The effects of C12/02 ratio, gas velocity, temperature and partial pressure of reactive gases on the reaction rate were investigated. The oxychlorination process was characterized by an apparent activation energy of about 214 kJ/mol. The reaction orders with respect to C12+02, C12 and 02 at 950 °C were about 0.65, 0.98, and -0.37, respectively. Some data about oxychlorination kinetics of MgO, Cr2O3, and MgCr2O4 contained in chromite were compared. Efficiency of using oxychlorination for the removal of iron oxides contained in magnesia was demonstrated.

Jan 1, 1999

By J. E. Dutrizac

A mineralogical study of a weak acid leach residue from the Clarksville zinc plant of Savage Zinc Inc. was carried out. The study focused on Pb and Cd as these elements most significantly impact on the environmentally acceptable disposal of the residue. The residue consists of major amounts of bassanite, zinc ferrite and various Zn-Pb-Fe-Cd silicate species. Also present are lesser quantities of PbSO4, sphalerite, Fe2O3 quartz, Mn-Pb-Fe oxides, SrS04, (Pb,Sr)SO4 iron gel-silica gel, jarosite and Ti oxide. The principal Cd carriers are the zinc ferrite, which contains up to 9.00% Cd and likely accounts for -45% of the total Cd content of the residue, and the various silicate species which contain up to 6.97% Cd and account for about 45 % of the total Cd. The sphalerite is a minor Cd carrier containing an average of 0.35 % Cd and accounting for -5 % of the total Cd; the other carriers contribute only trace amounts to the total Cd content. The major Pb carriers are PbS04, Pb-bearing silicates and Mn-Pb-Fe oxides. Minor proportions of the total 1.09% Pb content of the residue are carried by SrS04 and (pb,Sr)S04&apos; Trace Ph carriers include the iron gel-silica gel, Fe-Zn-AI oxide and bassanite. The residue after the toxicity characteristic leaching procedure (TCLP) is mineralogically very similar to the initial weak acid leach residue; the amounts of calcium sulphate are approximately the same in the two products. The principal Cd and Pb carriers are also the same as those noted in the initial residue, except that some dissolution and reprecipitation of Pb-Sr sulphate takes place. That the residue fails the TCLP test is likely a consequence of the superficial dissolution of Pb and Cd from species such as PbS04 or Zn-Pb-Fe-Cd silicate.

Jan 1, 1995

By S. Suzuki, Y. Maeda, N. Wakamatsu

"A new pyrometallugical technology, named KLS process, has been developed by Dowa Mining at its Kosaka Smelter to smelt various kinds of lead raw materials.The process consists of clearly separated two reaction steps, smelting and reduction. For this purpose, respective stationary furnaces are installed which are connected by a slag launder.Dry raw materials, together with pulverized coal and oxygen-enriched air, are injected through a lance pipe into the molten slag in the first furnace. It is kept under a high oxygen potential to remove sulfur completely. Resultant PbO rich slag overflows to the second furnace where pulverized coal and insufficient air are also injected through a lance pipe to reduce PbO to lead bullion and to compensate for thermal deficit. The entire operation is carried out continuously. The process development started back in 1981. In late 1986, a pilot plant with a capacity of 3.5t/H was constructed.Already nearly 20,000 tons of raw materials, mostly lead sulfate mixtures have been smelted successfully.IntroductionFor a long time, main raw materials for lead smelting at Kosaka smelter have been such secondary incombustibles as lead sulfate and lead-barium sulfate. The former is leach residue of the copper smelter flue dust and the latter originates from Iijima zinc refinery. While the most of lead concentrates produced locally has been smelted by an ISF of Hachinohe smelter in which Dowa Mining has a share.The surplus lead concentrates were processed at Kosaka by a hydrometallurgical method to convert PbS to PbSO 4 as pretreatment, and followed by simultaneous smelting together with the above secondary materials (1). Approximate output has been 1,5000 /M of lead bullion and slightly more than 2,000t/M of refined lead by adding lead bullion returned back from Hachinohe smelter (2)."

Jan 1, 1988

By F. W. Warnaars

Chanarcillo is a historically well-known silver deposit which produced over 100 million ounces. High grade vein-type mineralization is confined to a prominent set of nearly vertical, NNW to NE fractures that intersected limestones, andesites and tuffs of Early Cretaceous age. A significant amount of disseminated silver mineralization extends laterally outward from the fractures for considerable distances in pyritic carbonaceous limestones, whereas more competent volcanic beds rarely contain lateral mineralization. Local exposures of skarns are mostly barren. Silver and minor base metal mineralization was probably formed peripheral to a granodioritic intrusion inferred to exist at shallow depth. Part of this intrusion is exposed nearby where it contains significant hydrothermal mineralization and alteration. This intrusion was dated at 83.8 m.y.

Jan 1, 1987

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Shijie Wang

In pressure oxidation leaching of copper anode slimes, than 65% of the tellurium is m&apos; cxtraoted during decopperizing. About l0- 15% of the selenium is also dissolved simultane¬ously by severe leach conditions. Current operation for the treatment of the leachate is to constantly recirculate the leach solution through a bed of copper turnings. The tellurium and sele¬nium are precipitated from the leach liquor as copper telluride and copper selenide and sepa¬rated from the solution by filtration. In order to improve the reaction efficiency and reduce the process cost, viz, minimize the copper addition, cut retention time, and reduce the energy consumption; a chemical reducing agent is studied and the cementation process tested in the laboratory. In this paper, the test results are presented and the process chemistry is discussed.

Jan 1, 2003

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003