Search Documents

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Chikabumi Yamauchi

The comprehensive scientific development of conventional industrial technologies stimulates the creation of new ones in the next generation. Prof. Akira Yazawa has just accomplished such an important work in the non-ferrous pyrometallurgical field. The results of his successful research are immortal. The research group of the author has conducted since 1985 fundamental studies on the application of sodium carbonate slag to copper fire refining. In the present paper, a calculation method for the distribution ratios of impurity elements between sodium carbonate slag and molten copper will be shown. The specific treatment by sodium carbonate slag will also be presented as an effective way for reducing each impurity content in the molten copper to 0.1 mass ppm, which is the level required for the production of high purity copper. The thinking-out of this evaluation method gets a hint from the Equation (2) in the text which was proposed by Prof. Akira Yazawa.

Jan 1, 2003

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Zviad Kovziridze

It is stated that the specific character of SPHTS specimens of TiCx consists in crystal lattice strength reflecting the condition of synthesis in ?burning wave?. The use of roentgenographic and other methods of analysis allow to estimate the effect of the conditions of synthesis causing the carbon sablattice defect on the grinding intensity of TiCx -phases. The study of the kinetics of vibratory grinding of TiCx -phases in ethanol and benzene medium allows to establish high grinding intensity of the phases close to stoichiometry and the possibility of producing high dispersion powders (Ssp 4.5-6 m2/g).

Jan 1, 2006

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Roderick I. L. Guthrie, Donghui Li, Mihaiela Isac, Luis Calzado

The HSBC is an ideal process for the production of BMG strips. The purpose of the present work was to investigate the casting of Ca-based, bulk amorphous strips. The possibility of casting three Ca-based alloys (60Ca-20Mg-20Al, 60Ca-15Mg-10Al-15Zn and 55Ca-15Mg-10Al-15Zn- 5Cu (at.%).) was investigated, using the HSBC simulator. Numerical simulation and mathematical modeling were used to predict temperature variations and cooling rates, under different interfacial gaseous atmospheres (helium and air) near the meniscus region. Given the critical cooling rates and glass temperatures needed to be reached for the vitrification of the respective alloys, this leads to predictions of the critical thicknesses possible with this novel casting process. To validate our predictions, these alloys were then prepared and cast onto the sand-blasted, solid copper substrate mould of the HSBC simulator. The possibility of producing Ca-based metallic glassy strips via the HSBC processes was confirmed, using optical microscopy, X-ray diffraction and Scanning Electron Microscopy, to characterize the glassy properties of the cast strips. It was found that the HSBC process would be able to provide sufficient cooling to form amorphous strips for the 60CA-15Mg-10Al-15Zn and 55Ca-15Mg- 10Al-15Zn-5Cu alloys, but not the 60Ca-20Mg-20Al alloy.

Jan 1, 2014

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By N. Menad

. Electronic wastes are heterogeneous mixture, with mainly copper, aluminium and steel attached to or mixed with various types of plastics and ceramics. In general, small amounts of precious metals are incorporated in this mixture. Today, these components constitute an environmentally problematic fraction in disposal. Their physico-chemical characteristics have been investigated through chemical, x-ray diffraction, infrared spectroscopy, scanning electron microscopy and thermal analysis.

Jan 1, 2000

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By Viviane Tavares

The technology advance of mobile devices makes consumers of these equipment do more constant exchanges, with this the obsolete devices discarding becomes an environmental problem, due its landfill accumulation. In order to minimize the environmental impacts caused by these equipment there?s the recycling necessity of polymers, ceramic and metallic materials. The main goal of this recycling is to study the printed circuit board of device mobile processing through ore treatment in order to recoup copper. Initially printed circuit boards were processed in a knives mill, in order to liberate the ferrous material, after that it was done the magnetic separation of the reduced residue. With the not magnetic fraction it was done the grain sized analysis and sulfuric acid and hydrogen peroxide leaching analysis. With the chemical analysis results proceeding from the leaching aliquot it was possible to observe that the leaching method with sulfuric acid and hydrogen peroxide presented greater copper recovery.

Jan 1, 2009

By A. V. Tarasov, V. M. Paretsky

"A mathematical model of the low-temperature (soft) nickel oxide reduction (SNOR) in a tubular kiln has been developed including an equation describing changes in the nickel oxide content of the solid material along the length of the kiln; an equation describing the changes in the content of reagents ensuring nickel reduction (i.e., hydrogen and carbon monoxide) in the gas phase along the kiln length; as well as the temperature along the kiln length. The kinetic relationships used for the development of the model had been determined based on experiments conducted specially for this purpose. Model investigations were conducted to determine the distribution of such parameters along the length of the kiln as the contents of metals oxides in the solids, partial pressure of hydrogen and carbon monoxide, variations of the temperature depending on the SNOR process conditions, including the kiln rotation speed. Based on the data obtained, a simplified regression model of the reducing roasting process was developed.IntroductionAt the SeveroNickel complex (Russia) a technology has been developed and is being introduced on a commercial scale for low-temperature (soft) nickel oxide reduction (SNOR) in tubular kilns.The SNOR process has a number of advantages, the main of which are the higher degree of metallization and higher chemical activity of reduced nickel oxide attributable to the lower fusion of the surface of the grains of reduced material due to lower process temperature (800-1000°C) and improved reducing ability of the gaseous phase. However, the fact that the process is conducted in a gaseous phase sets higher requirements to the consistency of its composition necessitating careful continuous monitoring and control of the main process parameters."

Jan 1, 2001

By M. Ramprecht, M. Wu, A. Kharicha, A. Ludwig, H. Holzgruber

"The influence of the frequency of AC power supply on the magneto-hydrodynamic during the electroslag remelting process is studied. The focus is on the electrodynamic field and its resulting mechanical effects on the flow and liquid interfaces. The possible influence of the electrochemistry on the droplet formation is qualitatively discussed.IntroductionThe electroslag remelting (ESR) process is a secondary melting technique which can be used for a variety of metals and alloys, provided appropriate fluxes (slags) and melting parameters are employed. The ESR process is presently operating mostly with AC current of about 50 Hz. However for reasons primarily of inductive losses in the electric circuit, furnaces for ingots larger than 1 m, use or are projected to use current of very low frequency (< 5 Hz). Effects of lower frequencies (2.5-5Hz) on macrostructure and non-metallic inclusions were recently studied by Chang [1]. Most of investigations were performed either with DC power or with AC of 50-60 Hz [2-4]."

Jan 1, 2012

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By Stephen Gale, David Clarry, Edmund Smith, Jon Feldman

"In 2006, a Canadian steel maker embarked on an ambitious initiative to become “Best in Class in Energy Management”. This initiative provides the framework for this paper, with some augmentation from other energy management projects carried out by Hatch. The initiative focused on identifying energy/GHG management improvements leading to low-cost implementation of energy savings or GHG emission reduction. The key components of the approach were:• Review site energy management practices and benchmark internationally.• Review best technical practices and benchmark against public energy intensity data.• Conducted a site-wide Energy Assessment and physical review of operating areas.• Facilitation of on site-workshops with staff to prioritize savings opportunities, as well as identify and remove implementation barriers.• Development of an Energy Management Action Plan for implementation of improvements.Most organizations can produce, with relative ease, a list of ideas for saving energy, implementing them is the challenge. This paper addresses these issues as well as the profitability of the energy efficiency improvements and the consequences for GHG emissions.IntroductionWhen one of the authors was an undergraduate engineering student at the University of Cape Town in South Africa, the technical drawing instructor made a statement that was both humorous, and mildly profound. He claimed that the most successful engineer is one who is both lazy and diligent. Lazy, in the sense that the engineer is constantly on the lookout for an easier, more efficient, way to do something. Diligent, in the sense that the engineer will work tirelessly to come up with a good technical solution for the easier way. This paper, somewhat of an anomaly in a compilation of technical proceedings, hopes to break the mould a little, and to show a “lazy-diligent” way of reducing the carbon emissions from an industrial facility, using a steel plant as an example."

Jan 1, 2008

By Wantae Kim, Furnia Saito, Qiwu Zhang

"A novel mechanochemical processing technique for the preparation of zeolites from kaolinite in NaOH solution was investigated. Dry and wet mechanochemical treatments combined by subsequent moderate heat treatment could accelerate the synthetic reaction for zeolites from kaolinite. This stimulating process produced zeolite-A and zeolite-X from activated kaolinite at extremely lower reaction temperature than conventionally applied for zeolites production. Conversion to zeolite-A and zeolite-X was strongly dependent on the activated state of kaolinite. Wet mechanochemical treatment modified the chemical composition of activated solids. Rapid dissolution of AIO species rather than SiO ones in the reactant solution was accelerated by wet milling together with NaOH that promoted the formation of zeolite-X of high specific surface area.IntroductionZeolites are a family of hydrated alumina-silicate minerals contains alkali and alkaline earth metals. They have a framework structure that encloses inter-connected cavities occupied by large metal cations and water molecules. Zeolites are characterized for their ability toward ion exchange and reversible dehydration. Properties of them are exploited through commercial productions of particular structural and chemical features. Zeolites are used as commercial uses for catalysis for FCC (fluidized catalytic cracking) of petroleum refining, drying reagents of gases and liquids, and selective adsorbent for pollution control [1-3]. In such purposes, artificially synthesized zeolites are employed, although natural ones are associated with hydrothermal and hot spring alteration of volcanic materials. Commercially, a hydrothermal process has been used for the preparation of zeolite synthesis. This preparation method gives zeolites of high chemical homogeneity and purity, however, this wet-chemistry-based processing is significantly influenced by reaction temperature, pH, concentration, and composition of starting substances [4]."

Jan 1, 2000

By Muammer Kaya

The purpose of this review is to raise awareness about e-waste problem in the World. Whether generated at our home or our office, e-waste is most rapidly growing waste problem in the world. Even though there are conventional disposal methods (such as landfill and incineration) for e-waste, these methods have both economic and environmental disadvantages; recycling is a new waste management option which diverts end-of-life (EOL) electrical and electronic equipment (EEE) from landfill and incineration [1, 2]. Successful diversion strategy must be based on economic sustainability, technical feasibility and social support [3]. Recycling infrastructure includes transportation, collection, recovery and resale establishments. The first part of this paper describes the e-waste facts, how big is the e-waste problem and existing recycling programmes and collecting methods in the USA and EU; second part, describes various methods available to recover valuable materials (glass, plastic and metals (Pb, Cu, Al, Steel, Ni, Au, Pd, Cu etc)) in e-waste for a safe and environmental friendly disposal

Jan 1, 2009