Search Documents

By William Petruk

A mineralogical and image analysis study was conducted on samples of U tailings from pilot-plant runs on Midwest ore in Northern Saskatchewan. The tailings had been subjected to simulated weathering for the equivalent of 10 years in a tailings facility (lysimeter). The pH varied from 7.0 at the beginning of the test to 5.9 at the end. The results show that during the simulated weathering sane of the gersdorffite, uraninite, galena and pyrite had oxidized, with gersdorffite being the most reactive and pyrite the least. Reaction was evident at the top of the lysilleter , but was most intense at the seepage discharge. sane of the released ions precipitated as Ni, Pb, and U arsenates, sulfarsenates, sulfates and oxides on particles of all minerals. Green crystals of Ni sulfate and white crystals of ca sulfate had precipitated at the surface of the lysilleter. Clay minerals and chlorite had washed from the top of the lysirneter towards the seepage discharge.

Jan 1, 1989

By Jingwei Lou, Bing Li, Suzhen Li, Miao Shen, Jianguo Yu

"As a main impurity in primary lithium metal, magnesium is difficult to remove because of the very close relative volatility of the two metals. Electrochemical refining provides a possibility to completely remove Mg in the LiCl-KCl melt prior to Li reduction. MgCl2 reduction processes in LiCl-KCl- MgCl2 melt were investigated by cyclic voltammetry (CV), square wave voltammetry (SWV), chronoamperometry and chronopotentiometry. Then potentiostatic electrolysis was carried out and Mg (II) ion was reduced onto a liquid lead cathode from the LiCl-KCl-MgCl2 melt at the Mg deposition potential. The results show that Mg ( II ) is reduced in one step with two-electron transfer. The reduction potential of Mg ( II ) was well defined. The reduction of Mg( II) results in Li ( I ) underpotential deposition at 0.2V more negative potential than that of Mg( II) reduction. Therefore, in order to prevent Li ( I ) from codeposition with Mg, accurately controlling Mg ( II) reduction potential during the potentiostatic electrolysis was necessary. Ninety three to 99 % removal rate of MgCl2 was achieved after 8-12 h electrolysis when liquid lead was used as cathode.IntroductionMetallic Li has been widely used in batteries, light weight alloys and in fusion reactors because of its excellent properties. Currently, the only way in industry to produce metallic Li is by electrowinning from molten LiCl-KCl at about 450 °C [l-5]. LiCl-KCl is the only electrolyte used, because they presents a lower eutectic temperature and KCl shows a slightly higher theoretical decomposition voltage than LiCl, as shown in Table l .The produced metallic Li generally contains 1-2 wt% impurities including Na, K, Al, Ca, Mg, Si, etc. [6l, which are derived from the corresponding metal chloride compounds or metal oxide compounds existing in the LiCl and/or KCl raw materials. These impurities have to be removed by subsequent vacuum distillation at high temperatures to meet the requirements for metal Li purity in the final products. Separation of Mg from Li by vacuum distillation is difficult because their relative volatilities are very close, as shown in Table 2."

Jan 1, 2011

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By Qiang Zhong, Qian Li, Yongbin Yang, Tao Jiang

Thermogravimetric analysis (TGA) has been used to research the pyrolysis and combustion processes of coal used in rotary kiln of iron ore oxide pellet. Furthermore, the effects of air flow and oxygen concentration on the combustion behavior of coal were examined with TGA. The results showed that two individual stages can be distinguished for the pyrolysis of coal, the water evaporation stage and the de-volatilization stage. And the information on ignition and burnout characteristics can be obtained from the combustion process analyzed by TGA. Large air flow almost has no effect to the combustion process except that it enhances combustion intensity. However, the combustion process is further accelerated under oxygen-enriched conditions. With all experimental results, it could provide an attractive approach of analyzing coal for the rotary kiln process.

Jan 1, 2016

By Itsuki Uehara, Hiroyuki T. Takeshita, Tetsuo Sakai, Nobuhiro Kuriyama, Hideaki Tanaka

"AB5 type hydrogen storage alloys (A: rare earths, B: transition metals) are extensively applied to a negative electrode of a nickel metal hydride (Ni-MH) rechargeable battery for portable electric equipments, electric vehicles, hybrid vehicles etc. Performance of a hydrogen storage alloy electrode is affected by various factors, microstructure and surface composition of the alloy and structure of the electrode as well as composition of the alloy. Control of those factors enables us to commercialize the Ni-MH battery in various field.IntroductionA Nickel-metal hydride (Ni-MH) battery has been extensively developed because of (1) good compatibility with a nickel cadmium (Ni-Cd) battery, (2) high energy density (1.5-2 times higher per unit volume than a Ni-Cd battery) and high dischargeability, and (3) low environmental pollution. The charge/ discharge reactions can be written as [l, 2,3]:(+) Ni(OH)2+OH- = NiOOH+H2O+e· (E=+0.490V NHE),(-) l/6LaNi5+H2O+e-· = 1/6LaNi5H6+OH- (E=-0.828V NHE),where E° is a standard potential of an electrode vs. normal hydrogen electrode (NHE). Because of the above advantages of a Ni-MH battery, the battery have been widely used as a power source of portable computers, cellular phones, electric vehicles (Toyota ""LAV4L EV"", Honda ""EV Plus"" etc.) etc. Some hybride vehicles (Toyota ""Prius"" and Honda ""INSIGHT"") and fuel cell vhehicles (Toyota ""FCEV"") are power-assisted by a high-power Ni-MH battery. In 1999, the production of Ni-MH batteries reached 870 million cells in Japan. Most of commercialized NiMH batteries are incorporated with rare-earth-based AB5-type hydrogen storage alloy as a negative_ electrode. The production of rare-earth-based alloy is estimated to be approximately 8000 tons.The battery performances of the Ni-MH battery, for example, capacity, durability (cycle life), dischargeability (kinetics) and selfdischarge, ate closely related to the metal hydride· (MH) electrode, especially, the hydrogen storage alloy in the electrode. Substitution of alloy components, heat treatment, and surface treatment in order to change surface and bulk structure of hydrogen storage alloys have been examined by us and many reseachers in order to improve the performances of MH electrodes. This paper is a review of our and their efforts to improve performances of MH electrodes."

Jan 1, 2000

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates' at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

By P. T. Velu

Light weight aluminum alloys are the major construction materials for a number of structures in automobile and aerospace industries. Higher cost of production is the key impediment which restricts the usage of these alloys. A new electrochemical process route for the low cost production of aluminum alloys is being investigated, in which alloying elements are obtained from the dissolved compound. In the present investigation, solubility of lithium compound has been determined by measuring the EMF, when it is dissolved in the electrolyte. The solubility of Li2CO3 increased with temperature from 2.95 wt pct at 1063 K to 7.57 wt pct at 1093 K. Activities of the compound in the electrolyte were deduced using Temkin's ideal solution approach.

Jan 1, 1995

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By T. V. Jayaraman, D. Das, B. Mallesham, A. R. James

The PNN-PZT xPb(Ni0.3Nb0.67)03-(1-x)Pb(Zr0.31 Ti0 69)03 (0.2=x=0.6) based relaxor-ferroelectric material was synthesized by colurnbite precursor (NiNb206) method via conventional solid state reaction. Homogeneous mixture of required oxides and precursor was calcined at 850°C for 4 hrs to obtain phase pure perovskite. Pellets of PNN-PZT ceramics were sintered at 1100oC for 4 hrs. Phase pure perovskite structure was confirmed by the X-ray diffraction analysis. From the X-ray diffraction analysis it is also confirmed that there is a structural transformation from the rhombohedral to tetragonal with increase in PZT content and existence of morphotrophic phase boundary (MPB) at x = 0.5 composition. The morphology and microstructure of the sintered pellets were observed using the scanning electron microscope. P-E loop measurement shows the high remnant polarization (19.12 µC/cm2) and low coercive field (6.89 kV/cm) at MPB compared to all other compositions. The electromechanical planar coupling coefficient (kp) was measured through the resonance and anti-resonance method using the LCR meter. The piezoelectric strain coefficient (d33) measured directly using the d33-meter. At x = 0.5 composition the highest value of d33 = 398 pC/N is obtained.

Jan 1, 2012

By Yuanyuan Zhang, Patrick J. Masset

"The reduction of FexO in slag is one of the fundamental reactions in iron and steelmaking technology, including the blast furnace process (BF). Experiments on the reduction reaction of iron oxide using CaO-SiO2-Al2O3-FexO-C mixtures were carried out using thermogravimetric analysis (TGA) under reducing conditions at temperatures up to 1100°C. The composition of the primary slag was chosen so that the FexO concentration varied between 0 and 75 wt % and the CaO/SiO2 ratio being kept constant to 0.90. From the TGA curves recorded isothermally at different temperatures the kinetic parameters of the iron oxide reduction were determined.IntroductionIn blast furnace the iron ores and coke are charged in layers from the top. The reduction of iron oxide by coke is one of the fundamental reactions in the blast furnace process. Although a great amount of work has been done on the topic of reduction of composites [1, 2, 3], gasification of carbon [4, 5] and reduction of iron oxides by CO [4, 5, 6], the mechanism of reduction in iron oxide - carbon powder mixtures is not fully understood. Fruehan [1] and Rao [2] studied the reaction rate of the reduction of iron oxide by different types of carbon and concluded that the reaction mechanism is controlled by the oxidation of carbon at temperatures up to 1200°C. Rao [2] studied the reaction of hematite with graphite as carbon source up to 1080°C. An activation energy close to 300 kJ/mol was calculated within the temperature range of 950°C to 1087°C. In his study, Fruehan [1] determined the rate of reduction of Fe2O3 and FeO by coal, coke and coconut charcoal as carbon sources within the 900°C to 1200°C temperature range. He found that the reduction of Fe2O3 by carbon occurs in two stages and that the reduction of Fe2O3 to FeO is faster than that of FeO to Fe. This is due to the fact that the CO2/CO equilibrium ratio is higher, and hence, the rate of oxidation of carbon is faster. Fortini and Fruehan [3] have studied the reduction reaction of wustite by graphite and wood charcoal. They found that the wustite reduction can have a significant effect on the overall rate of reduction in composites at high temperatures or in the presence of a large excess of carbon. The calculated activation energy of the reduction reaction by wood charcoal was close to 368 kJ/mol, while the activation energy of the reduction reaction by graphite was 444 kJ/mol."

Jan 1, 2011

By J. Gartelmann, B. Zaslavsky, Y. Vojta, D. J. Chaiko, W. Mego, A. N. Rollins

"Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution.We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.IntroductionAqueous biphasic extraction (ABE) is a highly adaptable separation technique that can be used in a wide range of applications. We have been evaluating various types of ABE systems for possible applications in the treatment of solid radioactive wastes (1,2), liquid nuclear wastes (3,4), and contaminated soils (5-7), and in the removal of organics from aqueous salt solutions (8). We have also conducted fundamental studies of the solution microstructure of ABE systems using small angle neutron scattering (SANS) (9).The extraction systems are generated by combining an aqueous salt solution and an aqueous polymer solution. This produces two distinct liquid layers that are as immiscible as oil and water, yet each liquid layer contains at least 70 to 80 wt % water. The biphasic systems that we have been working with consist of immiscible polyethylene glycol (PEG) and salt solutions. Some inorganic salts that promote biphase formation with PEG solutions include the sodium/potassium salts of sulfate, carbonate, phosphate, and hydroxide (10)."

Jan 1, 1996

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

Adding CaO into the vanadium extraction converter is an effective way to decrease the dephosphorization burden in subsequent steelmaking process. The crystallisation process of spinel is one of the most decisive factors in the subsequent extraction. The theoretical calculation results show that the temperature of the peak total crystallization rate will decrease 5K with basicity increasing 0.1. The relation between cooling conditions and grain size of spinels is also discussed. It is found that low cooling rate and high basicity benefit spinel crystal growth. And the non-isothermal crystallization kinetics results indicated that the restriction factors of spinel growth is that solid crystals accept new components from liquid-solid interfacial. While the sample was cooled down to 1250 (1523K) at cooling rate of 5K/min, the crystal growth is consistent with Ostwald coarsening grew up law, and controlled by diffusion of particle.

Jan 1, 2016

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"In a typical year, approximately 1.7 million tons of residues and wastes are expected from Ajaokuta integrated steel plant, Nigeria. They will be generated mainly from sinter plant, blast furnace (BF), and basic oxygen furnace (BOF) operations and during rolling and finishing. The residues and wastes include slag, dust, sludge and slurries from gas cleaning, waste water, mill scales and other associated scraps. In this paper concepts for the utilization of residues and wastes in Ajaokuta Steel Plant where no reclamation routines have been provided for in the first and second phases of its project implementation is designed. The paper analyses the sources of the iron oxide wastes and evaluates the quantities expected from the main production facilities of the plant which include the two 312 m2 capacity sintering machines, the two 2000 m3 blast furnaces and two 130-T BOF (of the 2nd phase expansion of the Steel Plant). A reclamation routine designed for Ajaokuta residues and wastes is presented.IntroductionIn the steel industry, approximately 550kg of residues per ton of crude steel arise from the production processes and from pollution control facilities [1- 4]. These residues consist of slag, dusts and sludge, mill scale, spent pickle liquor, and other iron bearing materials. The main by – products generated in the steel industry are listed in Table I.Although major progress has been made in the recycling and use of some of these residues, particularly flue dust, blast furnace and steel making slag, yet a significant quantity are land filled or stockpiled. These unsightly stockpiles occupy valuable real estate and may become a source of environmental pollution if not otherwise disposed. In any case, the dumping option has become quite costly. For instance, one ton of iron ore costs between 28 and 34 US dollar, whereas as much as $20 per ton of steel produced is required to meet environmental compliance obligation in the USA [5, 6]."

Jan 1, 2008

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 GC under different pressures of oxygen. In the range from 300 to 500°C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

By Wilky Desrosin, Alicia E. Ares, Carlos E. Schvezov

"In the present research the horizontal directional solidification Zn-Sn alloys (Zn-4wt. %Sn, Zn- 6wt. %Sn, Zn-10wt.%Sn and Zn-30wt.%Sn) was carried out by extracting heat in two opposite directions. For this purpose, ceramic molds, a muffie, a horizontal furnace with two heat extraction systems at the ends, a measurement, acquisition and recording temperature system, eight K-type thermocouples and an electronic recorder were used. The main parameters involved in the columnar-to-equiaxed transition, CET, were: the moment of start and end of solidification at each position under consideration, cooling rates, the average temperature gradients and critical temperature gradients at the CET, the average speed of liquid and solid interphases left and right, advancing in opposite directions. Also, solidification kinetics was found to be different between horizontal solidification two-way heat extractions, with preliminary results of the vertical unidirectional solidification. In the solidification experiments, the velocity and accelerations of the liquidus and solidus interphases usually occurs at the end solidification zone of the samples.IntroductionSolidification of metal alloys, which starts in the external equiaxed region (chill), results in two basic types of structures in a single solidified alloy sample: columnar and equiaxed. The presence of both structures indicates the occurrence of the colunmar-to-equiaxed transition phenomenon[!].Studying the colunmar-to-equiaxed transition, CET, is of great technological interest for the evaluation and design of the mechanical properties of the solidification products. To this end it is necessary to understand the mechanisms by which it occurs. As found in previous studies [2-5], the CET occurs by competition between columnar and equiaxed growth. Mainly is controlled by the parameters of casting, such as the alloy composition, the density of the present nuclei in the liquid, the cooling capacity of the metal I mold, and the degree of convection in the liquid [7-10]."

Jan 1, 2014

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011