Search Documents

By Maryam Ghodrat, Bijan Samali

Disposal of waste syringes in a safe and eco-friendly way has been an issue of considerable scale for decades. The generated amount of waste syringes has escalated with the rapid growth in population and wide acceptance towards single-use medical devices. Some hospitals have their own on-site incinerators ,but recent tightening of air quality regulations and landfill levies led to the closure of manyon-site incinerators. The solution to this problem implicates the development of an environmentally-sound method that would employ these waste materials. This work investigates a thermodynamic modelling approach for incineration treatment of waste plastic syringes in Electric Arc Furnace (EAF) steelmaking. Mass balance was obtained from HSC Chemistry thermochemical package. The results indicate that the rate of iron oxide reduction in the slag is higher when coke is partially replaced by waste plastic syringes. Furthermore, the amount of dust and stack gas emission was reduced by around 0.4% and 1.25% respectively by replacing 20%-weight of pure coke with waste plastic syringes. The study demonstrates part of the coke can be successfully replaced by waste plastic syringes in electric arc furnace to provide additional energy from combustion without affecting the main process.

Mar 1, 2018

By L. Béjar-Gómez

The aim of this research work is to study and characterize the precipitates in structural microalloyed steel by transmission electron microscopy and analysis by low resolution. Microalloyed steel with niobium was produced by casting in an electrical induction oven of 25 Kg capacity. Carbon content in steel was less than 0.1 % and 0.036% of niobium. Steel was processed thermomechanically; reheated to 1250 °C and hot rolled on a laboratory mill to a 13.0 mm thick plate with a finish rolling temperature of 900ºC and a thickness reduction of 80% . This work shows what precipitates are present in steel, the type of precipitates and their morphology. Analysis by transmission electron microscopy of low resolution was applied to obtain the chemical analysis of precipitates and the matrix. Spectroscopy of dispersive energy (STEM - EDS) was applied to obtain the element profile of precipitates. Particles of precipitates of NbC were found; with cubic morphology and size from 70 to 130 nm, circular morphology and size from 10 to 70 nm, polygonal morphology and size from 10 to 80 nm.

Jan 1, 2006

By Gary A. Wickham

In the zinc industry, this past decade has seen both prosperity and depression. Significant changes have occurred throughout the world in mining, smelting, refining, and marketing. This paper will review many of the industrywide changes of recent years and the potential impact for 1990s. In addition to an historical review of supply and demand are discussion of technology considerations for zinc and zinc based products, effects of geographical shifting of markets, and projections for the 1990s.

Jan 1, 1990

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By Tom W. Gonzales

Magma Metals Company commissioned a 3000 tpd Outokumpu flash smelting furnace in July 1988. Through September 1992 the PSP has smelted a first campaign record 4.1 million tons of concentrate. This paper discusses modifications made to the original process equipment to overcome design flaws as well as future design changes currently under consideration.

Jan 1, 1993

By Maria G. Alves, Alexandre M. Stumbo, Francisca M. A. Pinheiro, Jonas Alexandre, Sergio N. Monteiro, Valdo da S. Marques, Paulo R. N. da Silva

"Brazil is among the few countries with potential for developing all sources of renewable forms of energy. In particular, the country is leading the world efforts of substituting petroleum based fuels for biofuels, such as ethanol and biodiesel. Most of the Brazilian petroleum, which has now achieved self sufficiency, is extracted from offshore wells located at the north region of the state of Rio de Janeiro. In view of the future depletion of petroleum, the State University of the Northern Rio de Janeiro (UENF) has created a Center for Alternative Energies (NEAL) to carry out R&D programs on renewable forms of energy. Today, the main project of the NEAL/UENF is a model park for generation of renewable forms of energy. The objective of this work is to present the structural concept of the park and discuss its contribution in terms of scientific, technological, economical and environmental benefitsIntroductionEnergy is presently a key issue in the world agenda for sustained development and environmental protection. It is of common agreement that the existing status of increasing use of fossil fuels, mainly petroleum, natural gas and coal will not only cause depletion of these resources with a consequent elevation in price but also climate changes, especially global warming. In fact, the humankind may be already facing an irreversible situation of climate alterations as well as reduction of conventional sources of energy. The worse predictions foreseen by specialists, still for this coming century, are dramatic disasters due to catastrophic weather in association with a profound energetic crisis. This scenario may, however, be avoided by actions that could effectively tackle the core of the problem. These actions have been suggested and discussed by scientists and leading authorities, especially in international symposia [1-3]. In particular, the Kyoto Protocol proposed goals for reduction of greenhouse gas emissions as well as a mechanism of carbon credits to allow for decreasing CO2 content in the atmosphere without affecting industrial production [3]."

Jan 1, 2008

By Henry L. Ehrlich

This survey compares bioleaching and biobeneficiation by autotrophic bacteria with that by heterotrophic bacteria and fungi Some physiological principles are reviewed. Advantages and disadvantages of autotrophic and heterotrophic leaching are discussed. Principles of anaerobic leaching by autotrophs and heterotrophs are introduced. and the advantages? over aerobic heterotrophic leaching are discussed. Examples of useful organisms in the autotrophic and heterotrophic categories are cited.

Jan 1, 1991

By David Seymour

Newmont Gold Company (NGC) located in Northeastern Nevada has been processing carbonaceous and sulfide refractory gold ores through a chlorination circuit prior to cyanidation. A "Flash Chlorination" pilot plant was installed in 1987 in an effort to obtain higher chlorine utilization efficiency and increase gold extraction. The Flash Chlorination process oxidizes organic carbon and sulfide sulfur. It also deactivates preg-robbing carbon, making the ore amenable to cyanidation. Significant recovery improvements were observed using this new process. This scheme has also been instrumental in the processing of higher than normal grade ores at economic chlorine levels. The Flash Chlorination pilot plant has been successfully treating carbonaceous ore on a production scale since April 1988. This paper summarizes laboratory and pilot plant optimization test work, using conventional and statistical methods.

Jan 1, 1989

By Luísa Maria Abrantes

Environmental control is becoming more and more stringent. As conventional processes for zinc production are pollutant routes, alternative methods have become an important subject of research. In this regard, the leaching processes have aroused a considerable interest, namely the electrochemically induced approach. The behaviour of zinc concentrate ore in the leaching processesses is influenced by several parameters. Chloride concentration and leaching solution pH, time and temperature of reaction were studied in order to evaluate their influence on the zinc recovery. The efficiency of the leaching process for zinc extraction is performed by factorial design. The experiments were carried out by 23 and 22 factorial designs of the factors. Results show that all factors, except for the time of reaction have a significant influence on the optimisation process, within each experimental region.

Jan 1, 2001

By Irsan Chandra

It is generally recognized that the gold thiosulfate leaching system requires the presence of copper and ammonia in order for acceptable leaching kinetics to be observed. However, the presence of copper and ammonia complicate the chemistry of the system as thiosulfate is rapidly oxidized by oxygen under these conditions. In addition, the environmental impact of ammonia would need to be considered before the adoption of this system. This paper describes fundamental studies into the thiosulfate oxygen system. The two reagents for this system are thiosulfate and oxygen, and leaching is carried out at pH < 7. It will be shown using electrochemical techniques that both the reduction of oxygen and the oxidation of gold-to-gold thiosulfate are hindered. Thus, if leaching is to work under these conditions, then both half reactions need to be improved. The use of additives, such as thiourea and lead have been shown to dramatically improve the oxidation of gold and the reduction of oxygen respectively. The leaching of gold in the presence of such additives is discussed.

Jan 1, 2003

Laboratory trials were performed in an induction furnace to study droplet formation during lance blowing. Compressed air was blown on a molten iron bath consisting of iron alloyed with carbon and silicon. Steel droplets were collected using a specially designed sampler. The average steel droplet composition and the oxide layer thickness were determined using scanning electron microscopy combined with energy dispersed spectroscopy. In addition, the concentration gradient of elements was determined using a microprobe. It should be noted that a special technique had to be developed in order to prepare the droplet sample. The size distribution and composition of the droplets was also determined using the microprobe. It was found that the carbon content in the droplets was lower than the carbon content in the bulk.

Jan 1, 2006

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By R. J. Chesher, J. C. Anzalone, T. F. Krusmark

The BHP Copper Refinery at San Manuel, AZ employs conventional electro-refining technology, plating at a current density of 335 A/m2 on six kilogram copper starter sheets. In 1995, a combination of variable anode chemistries and increasing current density in the tankhouse created periods of increased bismuth in cathode. Bismuth in electrolyte was minimized by bleeding electrolyte to the nearby BHP leaching facility. However, the expected drop in cathode bismuth was not achieved. Investigations indicated that starter sheets contained a significant concentration of bismuth. The bismuth was found to occur in combination with antimony on the surface of the sheet adjacent to the mother blank. Studies were conducted to determine the mechanism by which Group VB elements are incorporated into the starte sheets. Operational practices were introduced to minimize bismuth in starter sheets and improve cathode quality.

Jan 1, 1997

By E. T. White, Dean Ilievski

"Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known. This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal ""best"" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.IntroductionCrystallisation operations, including precipitation, are widely used in a number of hydrometallurgical processes to recover a desired component or to remove an undesired impurity. The goals of industrial precipitation processes are to maximise the recovery while maintaining product quality (generally product crystal size distribution, purity and morphology and product handling properties). Knowledge of the precipitation mechanisms and kinetics is invaluable for designing new precipitators or for improving existing units. The mechanistic and kinetic information is generally incorporated into mathematical precipitator models, which are then used for process design and optimisation."

Jan 1, 1996

By Charles L. Richman

The effect of the addition of Silver Sulfide on the rate of Chalcopyrite (CP) of Sulfuric acid (H2SD4 leaching is discussed, Although Ag2S in an expensive addition, a theoretical explanation of it&apos;s use will aid in the development of a economic substitution. We have used cyclic voltammography to show the presence reaction species at different potentials. Cyclic Voltammography maps the surface reaction current peaks on CP, to regions on the CP Phorbaix diagram. AC Electro-lmpedance spectroscopy (EIS) models the surface impedance properties, which control the rate of electron and ion transfer, and the surface kinetic reactions, with and with out light. EIS and other measurements show that AgCuS u Photo-reactive material- The EIS results are compared with the SEM and EDXA results to show the presence of diffusion pores, and diffusion controlled reactions during CP leaching without the addition of silver sulfate. We hypothesize that AgCuS is an ionic conductor like Ag2S. EIS shows an imposed negative leaching rate greatly. Our theory shows how the formation of Silver Copper (1) sulfide layer at open circuit potential gives an effect similar to negative potential, that is enhanced with illumination. We verify that AgCuAS is an N-type semiconductor that forms a diode type junction with the electrolyte with the Mott-Schoottly relation.

Jan 1, 2001

By Kathryn A. Mrotek

The textural growth patterns of nodules from two areas in the North Pacific and the South Pacific are characterized by mottled, columnar and compact-type zones. Amorphous material (mainly iron and manganese hydrox-ides) is a botryoidal-forming phase in the mottled and columnar zones. Crystalline material (platy crystals of birnessite and crystallites of todo-rokite) is found primarily in the mottled zones on botryoidal structures or as long-protruding structures growing onto that portion of the nodule in contact with the underlying sediments. The long-protruding mottled zones contain little or no biogenic debris, suggesting that these zones grew un-interruptedly within the underlying sediments. The coalition of spheroidal knobs comprising some of the nodules also suggests a relatively long residing time within the sediments. It appears that crystalline material (the usual host to associated valuable metals) forms in a quiet environment and as a result of direct nodule association with the underlying sediments.

Jan 1, 1982

By Fathi Habashi

During the recovery of copper, nickel, zinc, and lead from their sulfide ores, large amounts of sulfur dioxide are generated. A fraction of this gas is captured and transformed into sulfuric acid and liquid SOl and the remainder is emitted to the atmosphere. Numerous proposals were made to solve this problem. Hydrometallurgy offers the only valid solution by which elemental sulfur instead of sulfur dioxide can be produced. Sulfur can be easily stored, transported long distances, or transformed into S02 and H2S04 when desired.

Jan 1, 1996

By T. Ahokainen, J. Pitkälä, J. L. Xia, A. Jokilaakso, J. Vaamo

"The aim of the present paper is to use the two CFD codes to model the two phase flow in a water model ladle with central gas injection. The codes examined are CFX and Phoenics. An Eulerian two phase model is used and predictions are compared against the experimental data available. The results show that the codes can reasonably well predict the gas-liquid plume in the ladle, and predictions are generally in a good agreement with experimental data. However, differences do exist in predicting the gas volume fraction and velocity profiles. The results should be interpreted most carefully and cautiously, because they are very sensitive to the boundary conditions and dependent on the models for the physical phenomena involved. IntroductionSubmerged gas injection has widely been used in the metallurgical industry for more than a century. At the present, the use of gas is most effective in steelmaking industry where the advantages of the gas injection have already been long well understood. Effective mixing, large contact area between reactants, easy modifications and flexibility of the processes are the most important advantages. Disadvantages include refractory wear, blocking in the tuyeres, and splashing. These disadvantages can be reduced and advantages further improved by studying the flow phenomenon in process vessels. However, it is difficult to study flow in a real vessel because of the high temperatures and physical and mathematical modelling is therefore increasingly used in the process development work."

Jan 1, 1999

By XUEWEN WANG, Bowen Li, Mingyu Wang

A novel technology characterized by higher extraction of vanadium and recovery of valuable elements was developed to recover vanadium from stone coal. The brief flow of the novel technology mainly includes low temperature sulphation roasting, water leaching, recovering potassium, aluminum, copper and selenium, solvent extraction enrichment vanadium, precipitation of red vanadium, removal sodium from red vanadium and calcinations. The total recovery of vanadium reached 76.3%, which was higher than the current applied technology. The novel technology was environmentally-friendly and could extract vanadium from the stone coal, in which the content of V2O5 was less than 0.8%.

Jan 1, 2015