Search Documents

By Yuya Nakai, Kuniaki Murase, Kazuhiro Fukami, Atsushi Kitada, Ken Adachi

Concerning nodulation in copper electrore fining, it has been reported that short circuits caused by nodulation have the largest impact on the current efficiency. Therefore, to improve the current efficiency, it is important to prevent nodulation. In this research, the nodulation growth was investigated by replicating nodulation in the laboratory. The experiments were conducted by cathodic electrodeposition on copper plates attached to copper sticks of various heights. The nodulation was analyzed in terms of growth rates versus the initial heights.

Mar 1, 2018

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Solange Kazue Utimura, Amilton Barbosa Botelho, Carlos Gonzalo Alvarez Rosario

In this study, the recycling of waste materials is interesting in the environmental aspect to reduce the amount of waste in land fill and attenuate the pollution of groundwater, air and soil due to the liberation of dangerous elements. Recycling materials is an important issue once it represents a potential source of valuable metals. Waste printed wired boards (PWBs) as a principal part of Waste Electrical and Electronic Equipment (WEEE) and it is a fast growing stream with complex composition. The composite materials from PWBs are ceramic, polymers and metals. Biohydrometallurgical route may offer possibilities to recycle PWBs from discarded computers with the order to recover copper. The extraction of copper from PWBs by bioleaching processeswas studied using a mixed culture of acidophilic bacteria fromacid mine drainage (AMD) and the bacteria Acidithiobacillus ferrooxidans (A. ferrooxidans). The bioleaching experiments were performed in shaker flasks at temperature 30 °C and 170 rpmwith 10% (v/v) inoculum and pulp density of 35 g/L. Themetals concentration was determined by energy dispersiveX-ray Fluorescence (XRF). The results showed that the maximum copper recovery from PWBs using A. ferrooxidans was approximately 89% and with a mixed culture of bacteria from AMD the copper recovery was 92%.

Mar 1, 2017

By Robin M. Forbes. Jones, Suhas V. Patankar, Ramesh S. Minisandram, Jr. Carter, Kanchan M. Kelkar

"The nucleated casting process currently under development has the potential for production of Ni-base superalloy preforms that possess superior microstructure to product made by conventional casting processes, primarily for gas turbine applications. In this process, electroslag remelted (ESR) clean (i.e., free of ceramic inclusions) molten metal is conveyed via a watercooled copper Cold-walled Induction Guide (CIG) to a gas atomizer. The spray of clean metal droplets is then directly cast into a water-cooled crucible for ingot production. The microstructure of the resulting ingot preform evolves within the length scale of the individual droplets and is a function of the thermal state of the incoming metal droplets. This, in turn, depends on particle size, flight time and heat exchange with the gas phase.In the present study, computational models is developed for the analysis of the flow and heat transfer in the gas-metal spray system under axisymmetric and steady-state conditions. The gasphase flow is analyzed using an Eulerian framework and turbulent mixing within the gas phase is modeled using the two-equation k-e model. The dynamics of the metal particles is analyzed using a Lagrangian framework that involves calculation of the trajectories of the metal droplets. A two-way coupling is considered whereby the transport and heat transfer in the gas and the metal phases influence each other.The analysis is developed at two levels. The spray model performs a detailed calculation of the spray dynamics in the vicinity of the spray and is intended for predicting the temperature and mass flux distributions of the metal spray depositing into the mold. The chamber model enables prediction of gas flow and motion of metal particles in the entire spray chamber."

Jan 1, 2004

By David T. Bunney

In .December of 1987, International Mill Service, Inc. signed an exclusive licensing agreement with Tetronics Research & Development Co. Limited of Faringdon, Oxfordshire., England to commercialize plasma technology which had been demonstrated in an EAF dust processing application. The intent of the process is to reduce and volatize the zinc, lead and cadmium oxides inherent in EAF dust and collect these elements as metals in an ISP (Imperial Smelting Process) zinc splash condenser, and to render the resultant slag an inert, non-hazardous material. With these objectives in mind, IMS started commissioning facilities in 1989 at Florida Steel in Jackson, Tennessee and Nucor-Yamato Steel in Armorel, Arkansas. This paper will address the commercial development and progress of the technology at these two installations. Process Description In the EAF steelmaking process typically the off gas stream is cleaned by some form of baghouse. The particulate collected is known as Electric Arc Furnace dust and has been designated by the U.S. EPA as hazardous waste number K061, once it leaves the collection system. This designation was given to the material due to the high toxic concentrations of lead and cadmium (nickel and chromium for stainless EAF dusts) inherent in the dust. IMS' method of operation is to locate the facilities on the client mill's property adjacent to the baghouse. The dust is transported directly to IMS via a closed conveyance system. This method enables the technology to be an additional processing step in the steelmaking process. Once the dust has been transported to the IMS facility, it is fed, metered and mixed mechanically in the feed conveyance system with a carbon reductant (typically coke breeze). The carbon reductant is approximately 10% of the dust feed rate. This mixture passes through the feed system and enters the furnace

Jan 1, 1992

By I. C. Knight

The current levels of copper smelter by-product acid production are reviewed on a regional basis, together with the possible changes in the future. There will be increasing pressure for all smelters to achieve a sulphur capture level of at least 95% by the end of the decade.

Jan 1, 1996

By José García-Antón, Valentín Pérez-Herranz, José Luís Guiñón, Henry Reyes

"The majority of chromium electroplating operations employ Cr(VI)-based baths. During these processes, Cr(VI) is reduced to Cr(III). Besides Cr(III) other undesirable impurities are present such as iron, copper and nickel. The build-up of the impurities limits the lifetime of the plating solutions. Since the disposal of spent chromic acid baths is expensive and can cause significant environmental degradation, there is increasing interest in finding ways to regenerate waste chromium liquors.In this work, an electrolytic cell separated by microporous ceramic diaphragms was used to regenerate chromium plating solutions. The effect of the ceramic diaphragm structure parameters, such as porosity and pore size, on the performance indicators of the electrochemical reactor (fractional conversion, current efficiency, product yield, specific energy consumption) was investigated.The fractional conversion, the product yield and the current efficiency increased and the specific energy consumption decreased with the decrease in porosity.IntroductionChromic acid is widely used in industrial applications such as steel manufacture, metal finishing industries, aluminium anodising, pasivation of cadmium, magnesium, and zinc, etching of plastics and another industrial operations related with processing ferrous and no ferrous metals [1]. These processes employ baths with high concentrations in chromic acid, about 180 and 350 g/L, where hexavalent chromium is reduced to Cr(III):"

Jan 1, 2008

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

The fraction of liquid phase in sintered ore can be the most important factor to determine the sinter quality and yield in sintering process. The generation ability of liquid phase for mixture of iron ore powders is determined by basicity, roasting time, roasting temperature and chemical composition of iron ores. Five different iron ores were selected in this study and the dried powders of iron ore and CaO reagent (<200 mesh) were homogeneously mixed together at their required proportions, then 15g of the mixture was pressed under a pressure of 20MPa to make a cylindrical sample with a diameter of 20mm. The sintering temperature in this study was kept at 1280℃, the gas phase is air, the holding time was varied with its three levels of 5min,10min and 15min. After that, the sample was cooled under room temperature in the air, and the cooled sample was analyzed by using zeiss optical microscope. The mineral phase compositions were quantitatively determined with an open source image processing software, Image J whicn can calculate the fraction of liquid phase. Besides, the study on how to estimate the sintering behavior of the raw materials in different conditions by the theoretical calculation is of vital importance, and the development of this will greatly improve the sintering production. Factsage will be used to calculate the liquid phases formulation during the sintering. Comparing the experimental results and the theoretical calculation shows that the mass of liquid phase increases with increasing basicity during the sintering, besides, the mass of calcium ferrite increases with increasing basicity. The generation ability of liquid phase of iron ores can be predicted through the experiment verification.

Jan 1, 2015

By Lucas L. Costa, Luiz F. Lopes, Ludy C. Motta, Felipe P. D. Lopes, Sergio N. Monteiro, Lara S. Vasconcellos

"Environmentally correct materials like the lignocellulosic natural fibers, which are renewable and biodegradable, are being extensively investigated as possible substitutes for synthetic fiber in polymeric composites. Several natural fibers have never been thoroughly investigated as possible composite reinforcement. The fiber obtained from the leaves of the buriti (Mauritia flexuosa) palm tree is one example. Therefore, the objective of this work was to study the properties of buriti waste fibers, in amounts of up to 30%, reinforcing polyester composites.IntroductionIn the past century, the technological development gave priority to new synthetic materials with energy intensive methods of production. Today, there is a concern that conventional energy source such as petroleum, natural gas and coal are the main responsible for global warming. Therefore, the use of natural materials is gaining attention not only for the saving in process energy but also the renewable and biodegradable characteristics that make them environmentally correct. The lignocellulosic natural fibers extracted from cultivated vegetables like jute, sisal, hemp, coconut, flax, ramie and many others are typical examples. This type of fiber is being extensively investigated as a possible substitute for synthetic ones, especially the glass fiber, as composite reinforcement [1].A relevant example of lignocellulosic fiber substitution is nowadays occurring in vehicles. The automobile industry is applying composites reinforced with natural fibers to replace parts such as panels and seat cushions made of fiberglass or polymeric foams [4], as illustrated in Fig. 1. The practical reasons for this preference are that natural fiber composites present less damage to tools and molding equipments as well as relatively better finishing and less abrasive surface than corresponding parts made, for instance, of glass fibers. On top of these advantages, low cost is probably the main motivation for the industrial interest for natural fiber composites, especially in the case of residual fibers [5] or post-used fabrics such as jute sackcloth [6]. Natural fibers, however, are hydrophilic and will not form strong bonding with a hydrophobic polymer, normally used as composite matrix [1-3]. Another disadvantage is the heterogeneous characteristics of a natural fiber, which is typical of biomaterials. This results in a relatively great dispersion of dimensions and properties values such as the mechanical strength [1-3]."

Jan 1, 2008

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

Conventional ferronickel smelting has five main steps: Drying, calcination, prereduction, smelting and refining. In the scope of the current work, smelting experiments were conducted using Sivrihisar laterite ores (1.26% Ni) of Turkey. The ore samples previously subjected to drying, calcination and prereduction stages were smelted in alumina crucibles in a laboratoryscale horizontal tube furnace under argon atmosphere. Smelting experiments were performed at 1500, 1550 and 1600 oC. The amount of excess coal used in prereduction step was another variable. Sivrihisar laterite ore is a limonitic one with low MgO composition. Therefore, MgO was added to the smelting charge as a flux. The effects of experimental variables on metal Ni content and slag composition were investigated.

Jan 1, 2012

By G. T. Lapidus, O. J. Solis-Marcial

"The oxidative dissolution of copper from refractory minerals, such as chalcopynte, represents a technological challenge that has occupied hydrometallurgists for more than half a century. Innumerable processes have been suggested, but the majority operates at high temperatures or employs corrosive media. The origin of this refractory nature is the formation of passivating phases of iron(III) or copper. One option is to add non-corrosive ligands that complex these metal ions, thereby facilitating their dissolution. In the present work, the effect of acetone in sulfuric acid solutions was studied. The initial experiments were on chalcopynte carbon paste electrodes using cyclic voltammetry, where greater reactivity was observed. Later, leaching tests with hydrogen peroxide, cupric sulfate and ozone and, as oxidants, were performed. High extractions were achieved in three hours at 50°C. The solid residues contained the iron in the form of Fe203 and FeOOH.IntroductionChalcopyrite is the most important mineral of polysulfide copper ores [1] and accounts for approximately 70% of the world's copper reserves [2]. Currently, the copper present in chalcopyrite is extracted mainly by pyrometallurgical processes, which generate environmental concerns because of the formation of SO2 gas and submicron particulates [3]. The development of a less aggressive hydrometallurgical process for the extraction of copper would constitute a possible solution to these problems. For that reason, studies of the dissolution behavior of chalcopyrite are of great technological importance [4], However, the proposed oxidative leaching routes for chalcopyrite, generally at high pressures and temperatures, have not been implemented on an industrial scale, because of the elevated costs required to equal the high copper extractions obtained in thermal processes. These extreme leaching conditions are required because of the refractory nature of chalcopyrite. Passivation has been used to explain this phenomenon, although researchers have disagreed on the composition of the layer, which is various have assumed to be sulfur, copper sulfides, and iron-bearing jarosites or hydroxides [5]. If the latter compounds are the cause, an alternative solution would be the use of polar organic solvents in the oxidative leach to decrease the formation of the passivating iron layer. In this work, the influence of acetone on the oxidative leaching of a chalcopyrite concentrate at room conditions is explored."

Jan 1, 2012

By O. Kitamura, H. Kubota

The Harima Works started its ISP operation in 1966 and been expanding its production capacity from 3,000 tonne Zn/month and 1,500 tonne Pb/month to 7,500 tonne Zn/month and 2,500 tonne Pb/month. It is not only treating zinc, lead and bulk concentrates but also secondary materials like Waelz kiln oxide from the Shisaka Works of Sumitomo Metal Mining, waste treatment sludges, industrial wastes and others. Its final products cover Prime Western Grade (PWG) zinc, Special High Grade (SHG) zinc, continuous galvanizing grade zinc, electrolytic lead, cadmium, indium, thallium and sulfuric acid. This paper briefly describes the smelter's historical and present operations. The key data for the current impurity control management and for the distribution of impurities such as copper, iron and arsenic are presented.

Jan 1, 2000

By Ali Unal, Ali I. Kahveci

Alcoa developed a fractional crystallization process some 30 years ago as a method to purify aluminum. Depending on the purity of feed metal, it has been commercially used to make 3N7-6N purity aluminum. As an extension of this technology, Alcoa has experimented with purifying various aluminum alloy scrap for the purpose of recycling. Purified aluminum alloy scrap can be reused for making the same alloy. This presentation will discuss Alcoa fractional crystallization technology and its application to alloy scrap processing. Process capabilities and the partitioning of eutectic and peritectic impurities during fractional crystallization will be discussed for the alloy systems investigated.

Jan 1, 2000

By Bo Jiang, Lianyun Liu, Hongmin Zhu, Kai Huang

"Watermelon peel is selected as a novel adsorbent to remove Pb(II) from aqueous solution. A simple saponification process is proposed to modify the peel and the adsorbent is characterized by SEM and FTIR. The effects of pH, contact time, initial concentration of Pb(ll), biosorbent dosage and temperature on adsorption of Pb(II) are investigated. Different models are used to fit experimental data. These models indicate that the adsorption process follows the Langmuir model and pseudo-second-order model. The maximum adsorption capacity obtained from Langmuir model is 1.05mol kg-1 for the prepared sorbent. Equilibrium time is attained in 5-10 min for the studied concentrations. The watermelon peel can be used as an effective and low-cost biosorbent for removal of Pb(ll) from aqueous solution.IntroductionRecently, removal of heavy metal ions from industrial effluents by biosorption has become a very attractive topic, since the more serious pollution issues caused by heavy metals emerge frequently, and more strict requirements for its control are called upon by society [1,2]. In this case, most conventional purification technologies are not suitable due to poor cost-effectiveness [3]. For example, chemical precipitation by alkaline reagents usually can not decrease the metal ion concentration below the permissive levels, and also it will produce a large amount of sludge containing toxic metals. Membrane separation techniques can realize deep purification of wastewater easily, although its operating cost is usually high. Thus, considering the high effectiveness, low cost and free-sludge operation, bisorption has become a promising technique in water treatment [4]. The most important thing for this technology is the synthesis of a suitable biosorbent, whose adsorption properties will determine the removal efficiency and economic cost for the whole process. Watermelon is one of the most popular fruits for mankind for its delicious flavor. Usually, the watermelon is consumed mainly for its edible pulp, and its peel is discarded or only used as feed for livestock. Considering the pectin contained in the watermelon peel, just like that in orange wastes in the reported literatures [3], the idea of using it as the raw material to prepare the biosorbents for heavy metal ions removal from the aqueous solution was evaluated in this study."

Jan 1, 2012

By Milton Blander

"A review of concepts and theories for predicting thermodynamic solution properties of multicomponent high temperature liquid solutions is reviewed. During the last 50 years the ability to predict such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.INTRODUCTIONA number of solution theories and concepts have been developed which reliably predict the properties of multicomponent solutions from those of the lower order systems (often only the binaries). Because there is available data for a large fraction of the important binaries, the capability for making predictions for many multicomponent systems used in metallurgical separation processes is broad and potentially very useful. At the very least, the theories greatly minimize the data necessary for predicting properties of complex multicomponent solutions of molten salts, silicates and metals. It is the purpose of this paper to discuss the concepts which are demonstrably useful. We will discuss simple forms of the theories to make the concepts clear but we will refer to the publications which contain the more complex equations needed to treat the large majority of systems.A simple framework for understanding what we need to know in order to make technologically useful predictions is based on well known thermodynamic principles. In technologies and sciences where molten salts, slags magmas or molten metals are used or studied, one must often calculate the extent of a chemical reaction (or separation) or of phase changes. To do this, one must first write an equilibrium constant, K, for the reaction in terms of the standard free energy change of the reaction, ?G°."

Jan 1, 1996

By Richard P. Roberts

This paper will discuss the methods for the cooling of aluminum melting furnace? dross .and their impact on the environment. Also discussed will be a case history of an AROS Dross Processor installation, which is designed to maximize the recovery of metal content of the dross in a manner which is not only environmentally cleaner, but which also prepares the output in such a way as to facilitate downstream processes. Handling of the discharged material will be discussed in regards to the recycling of the preserved metal content and deposition of the unusable-materials.

Jan 1, 1992

By Uday Pal

In direct reduction processes for iron and steel making, significant amounts of Fe-C alloy droplets are generated and these remain suspended in relatively low FeO (around 5%) containing slags. Earlier workers have found that when the FeO content in the slag is <5%, the decarburization reaction becomes extremely slow (virtually ceases to occur) even though the alloy droplet contains a significant amount of carbons (2-3%). Understanding this rate controlling kinetic phenomena is crucial to designing an&apos; optimum direct steel making process. We studied decarburization of Fe-C particles by low FeO (<5%) containing CaO-SiO2A12O3 slags and found that by putting both the droplet and the slag in direct contact with an inert electronically conductive member that extends deep inside the slag bulk were able to quickly and completely decarburize the droplets. A detailed description and an explanation of the process will be presented.

Jan 1, 1995

By Kazutaka Kunii

It is invariably certain that after punching for IC Leadframes, scrap metal were generated. These seraps were re-dissolved and in order to use as raw material for leadframes, it is necessary to remove the Ni plating. In this study a simple method was developed for the removal of Ni plating by surface oxidation of Ni plating. For this purpose a fundamental study was carried out on the oxidation behavior of Ni plating. Results showed that by controlling the oxidation condition, a considerably high rate of Ni could be removed.

Jan 1, 1996