Search Documents

By Moo Eob Choi

A new process for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating secondary pollutants was developed at the University of Utah. In this process, sulfur dioxide is reacted with calcium sulfide to produce elemental sulfur and calcium sulfate. The latter is reduced by hydrogen to regenerate calcium sulfide. In the present work, the effects of different pelletization conditions for the initial reactant calcium sulfate on the strength and reactivity of the pellets were determined. These conditions include the type, amount, and impregnation method of catalyst, binder amount, and sintering. Experiments were also performed to determine the effects of temperature in the range of 973-1173 K, pellet size, cycle repetition, and water vapor or carbon dioxide content in sulfur dioxide stream on the reaction rates of the cyclic process. Nickel-catalyzed fired pellets produced by the use of molasses or cement as a binder showed good reactivity as well as high compressive strength during the cyclic tests. The binder amount did not significantly affect the reaction rate.

Jan 1, 2006

By Carlos Maurício F. Vieira, Lázaro A. Pizatto, Marcus Paulo Cardoso, Sergio Neves Monteiro, Joao Victor C. Nunes, Gustavo S. R. Matheus, Frederico M. Margem

The interest in composites with natural fibers is due, among other factors, to the growing worldwide concern with the preservation of environment and renewable raw materials. The natural fibers have many particular properties that make them an attractive alternative to traditional synthetic fibers. The advantages of using these fibers are: low cost, renewability, biodegradability, low toxicity, abundance and specific strength. The searching for new suitable, economically viable and technologically advanced materials justifies the accomplishment of this work that aims at comparing the mechanical behavior of polyester matrix composites with epoxy matrix composites reinforced with hemp fibers Izod impact tested. The specimens with dimensions: 10 63 12.7 mm, made in different volume fractions of fiber: 0–30 vol%. The samples were tested at PANTEC pendulum model XC-50 located at LAMAV/UENF. With this research was possible to analyse the mechanical properties of these two new materials.

Mar 1, 2018

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2: I. The samples having the density more than 99% of the theoretical value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical easting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By Bret Boster

Facilities at Amax Gold's Sleeper Mine process some 330 kt of high grade ore and 4100 kt of low grade ore annually to produce 6.8 t of gold and 7.8 t of silver. High grade ore is processed in a conventional milling facility employing gravity concentration, CIC and CIP unit operations for gold and silver recovery. Low grade ore is processed using heap leaching and carbon adsorption methods.. Presented are the evolution and descriptions of the Sleeper processing facilities and discussions of selected' operating results.

Jan 1, 1989

By Onuralp Yucel, Osman Halil Celik, Hakan Morcali

In this study, some experiments were performed for the dimensional control, pre-treatment, getting salt, metallic aluminum and aluminum oxide into the solution of 15 kg aluminum black dross obtained from a private company which recycles aluminium drosses. Water leaching experiments are done for removing salts and aluminum nitride. Temperature stirring speed, solid-liquid rate are investigated while water leaching experiments. Removing of AlN is provided at 25 °C at a rate of 42.48%, at 80 °C at a rate of 86.4%. Leaching experiments performed with NaOH. NaOH concentration and time was analyzed. Efficiency of including metallic aluminum into the solution is determined to be 98% approximately. Melting (fusion) experiments were performed with NaOH at high temperatures to include aluminum oxide in the structure of the remaining after dissolving process into the solution and after dissolving the resulting structures in water, efficiency of including aluminum into the solution is determined to be 85%.

Mar 1, 2018

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By R. Reed von Gal

The majority of zinc strip produced in the world today is cast on the Hazelett twiri-belt continuous casting machine. Ten of these machines are currently operating worldwide, and one machine is under construction for the People's Republic of China. The caster, which was first patented in 1947, was originally developed for aluminum and copper alloy casting. In the early 1960s, the design was expanded into zinc casting and within ten years the industry had essentially converted from casting and rolling ingots to twin-belt continuous casting with in-line rolling. The casting process employs two parallel, moving. water-cooled belts as the major mold surfaces. Together with two strings of side dam blocks, the design offers a four-sided moving mold which produces a continuous strip or bar. This paper will cover a bit of, the history, as well as the current technology surrounding this high production process for zinc strip production.

Jan 1, 1990

By Richard D. Hagni

The United States is dependent upon foreign sources for more than 93% of its bauxite and alumina supply. Domestic production of bauxite, which comes from Alabama, Georgia and Arkansas, is limited to those bauxite ores containing less than about l ½ % iron. Bauxites with higher iron contents are generally not utilized because they cause problems in bauxite calcining and especially because they produce undesirable brick discoloration and cracking. In order to improve beneficiation and expand the utilization of high-iron or ferruginous bauxites, a mineralogical and textural study has been conducted on selected samples from the Eufaula, Alabama, bauxite district. Reflected light microscopic, petrographic, and X-ray techniques have shown that a variety of iron minerals are present, including hematite, goethite, lepidocrosite, siderite, pyrite, marcasite, and ilmenite. Although the iron minerals may be locally concentrated into concretions and pisolites, most occur as very fine grains that are disseminated and show a variety of intergrowths. Mineralogical and textural observations indicate that the fine-grained iron mineral grains may be amenable to high gradient magnetic separation.

Jan 1, 1981

By Sue Xue, Carl C. Nesbitt

A project was completed which investigated the efficacy of recycling lead or lead monoxide from various fire assay wastes including crucibles, cupels and slag. The scope of the project was to determine optimal hydrometallurgical parameters so that direct separation and recovery of lead salts was economically feasible. A process was developed from the study which could use either acetic acid or nitric acid as a leachant, followed by several precipitation processes which could directly recover litharge (PbO) or other lead salts, such as lead carbonate or lead sulfate. The economics of the process is discussed. Analytical equipment such as the atomic absorption spectrophotometer and x-ray diffractometer supplied much of the information required for the study. However some novel analytical approaches using these instruments had to be developed to help in the determination of leaching kinetics and process quality control which are discussed.

Jan 1, 1999

By Afonso Garcez de Azevedo, Anna Carolina Lopes Rabello, Renan Tavares Vicente, Sergio Neves Monteiro, Amanda Maia Ferreira dos Santos

Civil construction is a sector of extreme impact in the Brazilian economy, with construction and demolition waste (RCD) having an extreme impact on the amount of urban solid waste. In this research it was proposed to propose a way of using these residues in the construction of concrete artifacts for structural use. Concrete specimens with sand substitution by RCD were produced in different percentages as a way to contribute to reduce,recycle and reuse thi large amount of waste from the construction industry. The objective of this work was to study the mechanical properties of structural concrete with total and partial replacement (25, 50, 75 and 100%) in sand mass. The results of the compression test indicate good quality for concretes with mass substitution of up to 75% per RCD.

Mar 1, 2018

By Ronald H. Church

Dewatering of mine waste slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in the slurry streams. Conventional treatment of fine waste slurries usually involves some form of impoundment treatment or storage. These impoundments present unique environmental problems. When filled to capacity, the impoundments are usually unloaded with a dragline and transported to a separate disposal area. The U.S. Bureau of Mines has conducted dewatering studies utilizing polymer technology in combination with a mobile field test unit designed by the Bureau. The purpose of these studies was to determine if the fine waste slurry from the mining operation could be successfully dewatered. Results of the investigation have shown that the slurry can be dewatered successfully. The dewatered products obtained from the tests ranged from 45 to 50pct solids. This material continued to dewater, approaching 70 pct solids within 24 h, and could be easily handled using conventional transportation equipment including conveyor belts.

Jan 1, 1994

By Akira Nishikawa

During the twentieth century the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By S. F. Cheng

Among the many extraordinary features of the rare earths are their magnetic and magnetoelastic properties. The rare earths, e.g. Tb, Dy, Nd, Sm, are known worldwide for their large magnetocrystalline anisotropy and magnetization, which has led to the importance of magnetic rare earths as vital ingredients of modem permanent magnets. In this paper, we focus on the strain dependence of these giant effects which gives rise to huge magnetostrictions, magnetomechanical couplings, and ?E effects. Magnetostrictions greater than 10-3 have been measured at temperatures as high as 500 K. At low temperatures magnetostrictions reaches -1%. ?E effects - 10. No other solid state material has matched these values. A proper balance of magnetic anisotropy and magnetostriction, plus a proper choice of crystal axes lead to alloys which can switch large quantities of energy between the internal (magnetic) and external (mechanical) states with the application of small triggering magnetic fields. In addition to the traditional use of these materials in transduction, they are particularly valuable for smart systems where reliability and robustness are needed such as active structure stiffening and active vibration control.

Jan 1, 1997

By Youn-Bae Kang

In order to overcome weak points of steel for its engineering applications, in particular, for environmentally benign, energy-efficient, lightweight engineering systems, a number of new steels have been proposed, especially to improve strength-to-weight ratio (specific strength). Mass production of these steels, however, has encountered a serious roadblock particularly in the steel refining and casting processes. This is because their chemistries and cleanliness requirements are vastly different from those of the conventional steels, and thus an incremental improvement of the prevailing process technologies is found hard to meet the requirements. In this study, a new process is proposed, which employs inert gas bubbles in the shroud nozzle, liquid steel drops in the degassing chamber, and the siphon transport for continuous casting. The proposed process which integrates the final refining and cleaning steps prior to casting is expected to be a technologically disruptive innovation on the conventional counterpart. The effectiveness of the individual steps is discussed with experimental results.

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. de Assis

Jute fibers are among the lignocellulosic with great potential for use in polymer composites. In this work, polyester matrix composites incorporated jute fabric were investigated for their flexural behavior. Specimens with up to 30% in volume of jute fabric were bend-tested until rupture. The results showed an increase in both the composite mechanical strength, principally to a polyester composite reinforced with 30% in volume of jute fabric. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the jute fabric and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.

Mar 1, 2018

By M. Bugdayci, Onuralp Yucel, K. C. Tasyurek

This paper is a contribution to the theory and quantitative understanding of the processes for the production of magnesium, calcium and strontium metals by metallothermic process. In the present study, effect of reductant type was investigated. Thermodynamic simulation of system was made by Fact Sage 6.4 program. In order to produce magnesium metal, effects of reductants “FeSi, Al, Si and CaC2” were investigated. To understand Calcium-oxide reduction system, effects of Al and CaF2 addition were investigated for different temperatures. In the last simulations, SrO reduction parameters were simulated. Al used as main reductant and BaO, CaO, CaC2 were added to green mixture as a functional additive. Finally probable phases and minimum reduction temperatures are determined.

Mar 1, 2018

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By Xiaolong Lin, Yuanbo Zhang, Jiann-Yang Hwang, Guanghui Li, Hongjin Zhang, Jiaxing Yan, Zhiwei Peng, Tao Jiang

The pollution caused by the spent printed circuit boards (PCBs) is currently a concern of researchers and environmental managers due to its large quantity and exceptionally complex properties. This study characterized printed circuit boards (PCBs) from discarded computers using a number of characterization techniques, including chemical analysis, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), granulometric analysis and scanning electron microscopy (SEM).The PCBs contain approximately 50 wt% metals, 25 wt% glass fibers and 25 wt% polymers. The principal metals include copper, calcium, tin, aluminum, zinc and lead. They are still wrapped by brominated epoxy resin after the PCBs are preliminarily crushed. As precious metals, such as gold and silver, are barely found in the PCBs, copper and tin are the main metallic elements of recycling value which warrants extra attention.

Mar 1, 2017

By Victoria Vaccarezza, Corby Anderson

Due to the demand for rare earth elements for everyday technology and applications, there has been much research initiation into the extraction and recovery of rare earth elements. An otherwise unknown mineral, eudialyte is a zircon silicate consisting of rare earth oxides, specifically the heavy REO yttrium (III), with only trace amounts of thorium and uranium. The first part of this project aimed at finding an efficient way to liberate and upgrade eudialyte to concentrate the REO content. A combination of gravity and magnetic separation techniques were employed, resulting in limited success. The second part looked at the hydrometallurgical processing of eudialyte through various leaching experiments with sulfuric acid. In all, this project will discuss why certain processes were utilized over others, as well as the difficulties that arose during processing.

Mar 1, 2018