Search Documents

By Ping-Ping Fan, Yong-Quan Wu

The polarized Brillouin scattering spectra were systematically measured to study the elastic properties of bulk hexagonal close-packed (hcp) ZnO single crystal in this paper. The peak polarizations of all modes in spectra were analyzed firstly. The elastic properties, such as the whole set of Elastic constants were accordingly calculated and compared with the previous literatures. Also investigated were the effects of the rotation of the sample in the (0001) plane perpendicular to the z axis on different acoustic modes. The results show that the quasi-longitudinal and quasi-transverse modes perpendicular to the (0001) plane act as the expected trigonometric function of the rotation angle,while the longitudinal and transverse modes on the (0001) plane remain constant.

Mar 1, 2017

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992

By Linlin Wu, Marlen Bertram, Chris Bayliss, Bernard de Gelas, Samantha Jones, Kurt Buxmann

"Environmental management is one of the industry cornerstones of sustainable development. In order to understand fully the environmental aspects associated with the raw material acquisition, production, use, and end-of-life operations of aluminium products, the Aluminium Industry has developed an approach based on Life Cycle Analysis (LCA) methodology.Within this framework, the Primary Aluminium Industry has established a global Life Cycle Inventory (LCI) data set. Inventory flows include inputs of raw materials, energy and water, emissions to air and water, and solid waste.This paper presents the latest LCI data update by the International Aluminium Institute for the year 2010, based on a survey of aluminium plants globally, including bauxite mining, alumina refining, anode production, electrolysis and casting. This update also includes some performance tracking based on the last LCI data collection in 2005, reflecting progress in efficiency and technology, as well as changes in the geographical location of the industry [2010 data pending]. IntroductionIn 2010 the Primary Aluminium Industry produced a total of 41 Mt of aluminium. The International Aluminium Institute (IAI) membership represents approximately 70% of total global production. The industry recognises the importance of co=itting to reducing the environmental impacts of producing primary aluminium, and the significance of working towards a more sustainable future. As part of this co=itment the IAI has developed an in depth Life Cycle Inventory programme, in which data is collected every five years, with supplementary key metrics collected annually.In 2003 the IAI released its first Report ""Life Cycle Assessment of Aluminium: Inventory Data for the Worldwide Primary Aluminium Industry"" based on the year 2000 with an update Report released in 2007, based on 2005 data.This paper presents the latest update for the year 2010 [2010 data pending]. It has been prepared with the same view of collecting all significant Life Cycle Inventory data (raw materials and energy use, air and water emissions and solid waste generated) associated with producing primary aluminium ingot from bauxite ore, with worldwide coverage. The intended purpose of the Inventory Report is to accurately characterize resource consumption and significant environmental aspects associated with the worldwide production of primary aluminium. It reflects the fuct that primary aluminium is a globally traded co=odity."

Jan 1, 2012

By Karen Tempel

Newmont's Lone Tree Mine is located 30, miles east of Winnemucca in Humboldt County, Nevada. Starting in February 1994 a pressure oxidation circuit was commissioned to treat refractory gold ores. Gold is leached and recovered from the oxidized slurry in a six-stage carbon-in-leach (CIL) circuit. Lone Tree has been able to maintain tighter control' of cyanide addition and reduce cyanide consumption its CIL circuit through the installation of Degussa's Cyplus® CCS Cyanide Control System in the spring of 2000. 'The Cyplus® CCS, along with additional inputs' from plant sensors, has allowed tor a more efficient and effective control strategy over the manual control method used ,in the past. This paper documents the key aspects of the Cyplus® CCS installation; the development of the control strategy, and the benefits achieved from enhanced control.

Jan 1, 1998

By Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial ofthe detoxification ofchromium slag in cyclonefurnace and the preparation of glass-ceramics were investigated in a power plant in China. 10wt.%chromiumslagweremixedwithpulverizedbituminouscoalandlimestone as the raw materials of the cyclone furnace. Cr(VI) in chromium slag was reduced toCr O insidethecyclonefurnace.Themeltwaswater-quenchedintofritandthen 2 3 fired into glass-ceramics with a laboratory ceramicrollerkiln. The preparation and crystallization behavior of glass-ceramics were investigated with differential ther- mal analysis (DTA), physical and mechanical properties testing, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The optimal flexural strength exceeding 90 MPa were achieved in firing temperature zone of 1170–1200 °C. Anorthite (CaAl Si O ) and diopside [Ca(Mg, Fe)Si O ] can be identified in the 2 2 8 2 6 glass-ceramicsandCaAl Si O isthepredominantcrystalphase.Fineparticleswith 2 2 8 average diameter of 200 nm distributed uniformly in the glass-ceramics. Granular crystals are intensively interconnected and constituted a crystal skeleton soaked in theglassmatrix.LeachingtoxicitytestdetectedCr(VI)of0.016and0.010 mg/Lof the water-quenched frit and glass-ceramics, respectively. This method provides an effective and comprehensive technique for the detoxification and utilization of chromium slag at low cost and large-scale. (cid:1) (cid:1)

Mar 1, 2018

By Noboru Masuko, Sachiko Ono

"The structure and composition of anodic films formed on aluminum in a borate solution have been investigated by using TEM and SIMS with respect to the effect of current density and electrolyte temperature. The film is composed of a boron-containing outer layer and a boron-free inner layer with disc-like crystals present at the interface. The thickness of the film formed at constant current density up to an identical voltage, decreases with increasing current density. The thickness increases remarkably with elevated temperature. The transport number of Al3+ estimated from the thickness ratio .of the cuter to the inner layers is 0.4 when the film is formed at the current density of 20 Am-2 at 60°C. It increases slightly with increasing current density and decreases significantly with increasing temperature. Content of boron in the outer layer increases 1.5 times when current density .increases 10 times. These changes in film structure and composition with electrolysis conditions must have a significant role in the determination of electric properties of anodic alumina films as a capacitor material.IntroductionThe growth of anodic alumina film in ·a neutral electrolyte proceeds at both film/electrolyte and film/substrate interfaces giving a duplex structure. The oxide layer formed at the former interface includes electrolyte anions while a-pure alumina layer is formed at the latter interface. The thickness ratios of each layer respectively represent transport numbers of Al3+ and 0 2 - (1). The film thickness and the incorporated anion content as well as transport numbers of both ions must affect the dielectric properties of the film as a capacitor material. However, the correlation between film structure and electrolytic conditions is not fully understood (2). For the further clarification of anodic film growth mechanism, more detailed characterization of anodic films in relation to electrolytic conditions is advantageous. In the present paper, therefore, the effect of current density and electrolyte temperature on the microstructure and composition of anodic barrier films formed in a neutral borate solution was studied. The films were characterized by direct observation using transmission electron microscopy (TEM) and depth profiles of constituent elements obtained by secondary ion mass spectroscopy (SIMS)."

Jan 1, 2000

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By Gabriel Riveros, Ariel Balocchi, Andrzej Warczok, Daniel Smith

Blister copper from converting of copper matte is processed by fire refining prior to electrorefining. The fire refining consists of two steps: copper oxidation with impurities slagging and copper reduction. The classical batch process is carried out in vascular or reverberatory furnaces called anode furnaces. A new process for continuous copper fire refining has been proposed. The copper flows through two reactors in cascade, where is oxidized and reduced. The flow of a liquid copper through a ceramic packed bed increases the surface area and the rate of oxidation as well as the rate of reduction in the packed bed of charcoal. Mathematical modelling allowed for the design of a laboratory scale demonstration installation and industrial-pilot installation in Hernan Videla Lira Smelter (Paipote). The results have demonstrated the process feasibility and flexibility in operation.

Jan 1, 2009

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Thomas P. Battle

Modern-day direct reduction of iron first developed as a small-scale, low capital and operating cost alternative to the blast furnace. Since commercialization of continuous DR technology in the late 1960s, the market for the products of direct reduction has grown to more than 74 million tonnes in 2012. The initial advantages of DR plants over BF facilities have grown over the years, for several reasons, including the increased size of DR modules, lower energy and emissions (particularly CO2), along with the flexibility to use a number of different reductants. The development of DR technology over the past forty years will be emphasized in this presentation, including recent developments that allow for even more direct sustainability comparisons with the iron blast furnace – and even combine the two technologies for improved synergies. Also briefly discussed will be the possibilities of using direct reduction for non-ferrous ores.

Jan 1, 2014

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

Experimental oxidation tests at high temperature (1000-1200 °C) on SiC samples have been respectively performed under wet and dry air atmosphere for different holding times. The thickness of thermally grown oxide was experimentally measured by DEKTAK Stylus Profilometry. The results showed that the oxidation rate was increased with temperature and holding time, corresponding to a passive oxidation regime which led to the formation of SiO2 layer. The sessile drop method was employed in order to measure the contact angles between Si and SiC at high temperature. Contact angle can be varied from 39.6° to 75.6° by controlling the atmosphere. The deoxidation of the oxide layer and infiltration of liquid silicon caused a decrease in the contact angle.

Jan 1, 2016

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014

By Cz. Mazanek

Specific biostimulating and anticancerous properties have been observed in peat, Ash Vacanta, and in an amorpous silica that is obtained as a by-product of alumina production from Turow clay in Poland. The anmphous silica was characterized and found to have a large specific surface area. This property may account for the beneficial characteristics of the material.

Jan 1, 1989

By Michael A. Krstich

A soil washing pilot plant to treat soils at the U.S. Department of Energy (DOE) owned Fernald Environmental Management Project (FEMP), was designed based on extensive bench-scale testing. The system's design incorporated a combination of physical separation and' chemical extraction processes and was tested on two soils. The textural composition of the two soils was approximately 20 percent sand, 60 percent silt, and 20 percent clay. Since this grain size distribution was not considered optimum for physical separation techniques, thesoil washing pilot plant had to be designed with selected equipment to provide specific soil size fractions during processing operations. A trommel, vibrating screen deck, centrifuge, and attrition scrubber were used in the system to selectively separate specific soil size fractions at 4.75, 2, 0.3, and 0.02 millimeters (mm). The trammel used high pressure water [1000 pounds per square inch (psi)] during the initial step of the process to reduce soil aggregates to single grain composition, separate out greater than 4.75 mm gravel, and dislodge chemical contaminants from the individual soil particles. The vibrating double-screen deck provided 2 - 4.75 and 0.3 - 2 mm soil fractions that, when combined, averaged greater than 75 percent solids for both soils. The centrifuge was designed to take the less than 0.3 mm soil slurry from the screen deck and produce a particle size of 0.02 mm. The centrifuge produced a high solids stream that averaged greater than 70 percent solids for both soils. These 0.02 to 0.3 mm soil solids from the centrifuge were combined with the 0.3 to 4.75 mm soil solids from the screen deck and processed through the attrition scrubber. The data collected from the pilot-plant operation was used to aid in the design of a full-scale system and was instrumental in formulating full-scale process operations and the selection of equipment.

Jan 1, 1995

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By Seksak Asavavisithchai, Natthida Jareankieathbovorn, Areeya Srichaiyaperk

"Recycling of ADC12 alloy scraps for fabrication of open-cell aluminium foams has been conducted via pressure infiltration method of replication process. The scrap, up to 50 wt.%, was melted with pure aluminium billet, followed by infiltration in a replicated mold of polyethylene foam structure. Compared with the pure aluminium foam, the compressive strength and hardness are higher for the foams with recycled scraps. The increase in foam mechanical properties is due to the presence of Si hard phase in Al matrix. The strength and hardness of the foams also increase with increasing contents of the scraps.IntroductionRecently, open-cell metallic foams have been brought to considerable attention of many industries due to their superior properties; such as large surface area, high specific strength, thermal conductivity, high service temperature and excellent anti-microbial activity, that cannot be found in conventional materials [1, 2]. Typically, open-cell foams are used in functional applications for which a requirement of high strength materials is not demanded. Good examples of such applications include heat exchangers, bone-replacement implants, interconnects, catalyst supports, and sound insulators.Among all types of open-cell metallic foams, aluminium (Al) is the most widely used base metal, due to low material cost, low density, low melting temperature and good corrosion resistance. To improve mechanical properties of Al foam, modification of foam microstructure with addition of alloy elements or ceramic particles is commonly carried out [3, 4]. ADC12 alloy is a typical die-casting Al alloy with high content of silicon (Si) close to the eutectic point in Al-Si binary phase diagram. The alloy is extensively used in the casting industry, due to high wear and corrosion resistance, low coefficient of thermal expansion and excellent castability [5]. The mechanical properties of Al-Si alloy are strongly dependent of Si content."

Jan 1, 2012

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018