Search Documents

By Christina V. White

An experimental study was undertaken to investigate the feasibility of utilizing vapor transport for the treatment of heavy metal contaminated smelter soils. The focus of this project was to develop process chemistries that would make incineration a viable process for the treatment these soils. The experimentation concentrated on the elimination of arsenic, cadmium, and lead, and was performed in a laboramry scale rotary kiln setup. Three soil samples from non¬ferrous smelter sites, which contained various concentrations of contaminants, were utilized in the experimentation. Three chemistries were investigated for the volatilization of the heavy metals: Chloridizing volatilization, ferric chloride vapor complex formation, and the use of oxygen potential control. The samples were analyzed for residual heavy metals so that the extractions could be determined. However, the ultimate test was the leachability of the residual arsenic, cadmium, and lead, as determined by the TCLP test. The results firmly establish that incineration is a feasible process for the treatment of metal contaminated soils. It was found that no one process chemistry is suitable for all different soil samples. A two-step process consisting of a reducing step followed by a hydro-chlorination step was required to make Soil Sample-B pass the TCLP tests for all three heavy metals. Soil Sample-A passed the TCLP tests for arsenic, cadmium, and lead using a hydro-chlorination process at a minimum temperature of 700°C. In addition to passing the TCLP mm for Soil Sample-A and Soil Sample-B, 70 to 80 percent removal of the impurities was accomplished. This demonstrates that the leachability of the impurities was decreased primarily due to the removal of a large fraction of the contaminants, Soil Sample-C possessed very high levels of cadmium and lead and only moderate extractions of the impurities were generated from this soil. The arsenic TCLP test was passed at 500'C using a process gas containing ferric chloride and at temperatures of 700°C and above using chlorination of hydro-chlorination.

Jan 1, 1996

By T. T. Chen

A mineralogical study of copper anodes and copper anode slimes was carried out to elucidate the silver phases present and the behaviour of silver during copper electrorefining. Most of the silver in the anodes is in metastable solid solution in the copper metal. As the copper dissolves, silver also dissolves, but is rapidly removed from solution by a variety of reactions. Some of the silver is precipitated as Ag by cuprous ions and some is precipitated as a complex CU-Ag-Pb-As-Se oxidate phase. Much of the silver, however, reacts with copper selenides to form, progressively, (CU,Ag) 2se, AgCuSe and Ag2se. The reaction commences at the periphery of the selenide grains and progresses inward; the result is commonly a silver-rich species on the outside of a silver-deficient core. Slimes collected periodically throughout the electrorefining cycle show a progressive silver enrichment of the selenides. Traces of Ag2Te also may be present, but the telluride seems to J:ie a rare constituent of most raw anode slimes.

Jan 1, 1989

By Donald I. Bleiwas

World primary nickel production in 1987 is projected to be 770,000 mt, slightly higher than that in 1986. Market economy country (MEC) production in 1987 is projected to be about 524,000 mt, an increase of almost 5 pct over 1986 production. Production cutbacks and closures at Japanese ferronickel plants in 1987 resulted primarily from the strong yen and higher energy prices. Cutbacks also caused reductions in ore production from Indonesia, New Caledonia, and the Philippines. Technical problems affected production, to varying degrees, in Botswana, Indonesia, and Yugoslavia. World primary nickel production for 1988 is projected to be 787,000 mt, of which 536,000 mt will be produced in MECs. Increased production is projected from Botswana, Canada, Cuba, and possibly Greece and Yugoslavia, while slight production decreases are projected for Indonesia, New Caledonia, the Philippines, and Zimbabwe. .. South African nickel production in 1988 could be severly curtailed by social strife. In the early 1990's Brazil and China could be major economic competitors to Western nickel producers.

Jan 1, 1988

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015

By Stephen J. Hales

State-of-the-art Resistance Spot Welding (RSW) equipment has the potential to permit adaptive feedback through recent advances in computerized process control. The initial step toward achieving this goal involves assessment of the effect of specific variables and the interaction between these process inputs on spot weld characteristics. This investigation addresses this issue through the application of Taguchi methodology to understand and refine a RSW schedule developed for joining of two dissimilar aluminum-lithium (AI-Li) alloys of different nominal thickness. The experiment was designed to establish a hierarchy of inputs with respect to each 'other, and to determine the significance of these inputs with respect to experimental noise. Valuable insight was gained regarding the interaction between process variables and the effect of certain equipment-related changes. In spite of a decrease in equipment performance, an improvement in the maximum strength attainable for defect-free spot welds resulted from the application of the statistical experiment.

Jan 1, 1992

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill. During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By M. Tomita

One of the most essential factors for a custom smelter to strengthen its competitive power is to Improve its comparative standing in purchase of concentrates from the world market. It is especially critical for Japanese smelters who depend almost 90% of their raw materials on import. In order to accomplish this breakthrough, the development of the new technology which enables us to treat concentrates containing higher Impurities is inevitable. Nippon Mining Company Ltd. made an intensive research on processing complex ore for three years from 1979, and successfully developed an original hydrometallurgical process to treat converter dust for eliminating impurities from the copper smelting circuit. The commercial plant was constructed at the Saganoseki Smelter & Refinery in 1982, and its nine years operation has been satisfactorily proven the advantages of the technology. The concept of this process and its operational performance are discussed.

Jan 1, 1992

By You-Hai Wen, Yinkai Lei, Tian-Le Cheng

A phase field model is developed to simulate the performance of SOFC electrodes. By solving the conduction equations on both the electrolyte and electrode phases, and incorporating the three-dimensional microstructure and reaction front at triple phase boundaries, the current-voltage relation of an electrode is directly simulated. By further coupling it to our recently developed coarsening model, we are able to investigate the effect of initial microstructure on the performance degradation in SOFC electrode. This model is applied to LSM-YSZ cathodes with different LSM volume fraction. The volume fraction effect on the electrode performance and its degradation rate has been analyzed and discussed.

Mar 1, 2018

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By M. H. Staia

A Venezuelan ilmenite concentrate has been chlorinated at a temperature of 700" C by carbon tetrachloride. In the experimental rig, built at laboratory level, the direct chlorination process yielded a TiCI, recovery of approximately 85% after 280 minutes processing. The partial pressure of carbon tetrachloride was nearly atmospheric (0.94 atm). Product vapors from the reactor were fractionally condensed in a condenser which was maintained at a temperature of 250°C meanwhile TiCl, vapors were condensed in refrigerated coils at a temperature of -20°C. The concentrate used in this investigation was obtained by applying gravitational and magnetic concentration methods to the black sands. The experimental results have shown the need to asses the influence of the weight ratio of ilmenite to carbon tetrachloride on the resultant products. The equilibrium of the heterogeneous system has been calculated taking into account the initial experimental conditions.

Jan 1, 1995

By C. A. Natalie

Prediction of average residence times for different particle size intervals during sulfide roasting was investigated. Calculations were done to predict average residence times using a model which employs empirical correlations for elutriation constants. Experimental average residence times were determined using a continuous., six inch diameter,. fluid bed roaster and compared with calculated residence time values. Comparison of calculated and experimental data showed that geometry effects may have .been significant when attempting to apply elutriation data to this roaster.

Jan 1, 1985

By Faustino G. Prado

In the, quest for an economical and environmentally friendly reclamation of metallurgical dusts generated during pyrometallurgical operations, our goal has been the separation and recovery of most of the components, as well as the complete recycle of all the reagents. Effluents have been avoided, within acceptable economic parameters. This presentation, which can be applied to a large spectrum of dusts and other residual-materials-, has focused on the dusts generated by the operation of Secondary Copper Smelters. Those dusts show a wide range of components, including zinc, lead-, copper, cadmium, tin, chlorine and-alkalies. Our present work deals with the use of ammonium salts in the separation and recovery of-the above mentioned elements in a marketable form. Most of the chemistry and techniques involved have teen already confirmed in commercial scale operations. Others have gone through pilot scale tests or bench scale tests. The recycle of reagents has also been- confirmed at the same operating levels. A preliminary evaluation indicates that the chosen route, in addition to a viable economy, offers a complete and safe reclamation within the most strict environmental regulations.

Jan 1, 1995

By Alexey T. Kovalev, Irina A. Khabarova, Valentine A. Chanturiya, Igor Zh. Bunin, Elizaveta V. Koporulina

"The paper presents new theoretical and experimental results about mechanisms of disintegration of mineral complexes and structural transformations of the sulfide surface under high-power nanosecond electromagnetic pulses (HPEMP). The heated gas outflow from nanosecond breakdown channels of sulfide minerals under HPEMP is considered. It is shown that the gas outflow from channels can be an additional destructive factor in the processes of the electric pulse discharge disintegration of mineral complexes. It is shown that the effect of HPEMP changes chemical surface composition and, respectively, technological properties of pyrrhotite and pentlandite. Morphology and elementary composition of new micro- and nanoformations on mineral surface of pentlandite and pyrrhotite have been investigated using up-to-date methods of SEM/EDX and Scanning Probe Microscopy. Preliminary electropulse effect on mineral products before flotation allows producing optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new nanophases and defects on the surface of sulfides.IntroductionThe effectiveness of High-Power Nanosecond Pulses in the disintegration and liberation of fine disseminated mineral complexes and the recovery of micro- and nanoparticles of precious metals from refractory ores was demonstrated in [1, 2]. Possible mechanisms of selective disintegration were considered in [1-3]. It has been shown both theoretically and experimentally that electric breakdowns can play an important role in the nanosecond pulsed treatment of milled minerals (e.g., semiconductor sulfides and quartz with particle sizes of 100 µm to 2-3 mm) that are carriers of finely disseminated gold and other valuable components. Electric discharges in such minerals are accompanied by a destruction of integrity in the form of breakdown channels and the formation of a system of cracks around these channels [3]. The development of the domains of induced cracks around the channels is determined by the pressure of evaporated material in the breakdown channel. Upon an instantaneous energy release in a channel (nanosecond discharges), the change in its transverse size and in the gas density and pressure in the channel is determined by (i) the radial motion of the evaporation wave, (ii) the radial expansion of the channel, and (iii) the heated gas outflow from the channel. The evaporation wave moves with a speed on the same order of magnitude as the speed of sound (or greater) and travels a distance of around the initial channel radius, i.e., a much smaller distance than the breakdown channel length."

Jan 1, 2011

By Robert Vidal

The performance of a laboratory-scale cell for the electrolysis of an aqueous chrome alum solution was studied. Electrode potentials, pH, and Eh were recorded. An optimum catholyte pH of about 2.5, consistent with information from the literature was observed. Values exceeding this range resulted in a precipitate formation and are detected by wavering cathode potentials. The role of anodically produced dichromate ions was investigated by chemical analysis. It was found that the steady state concentration of dichromate ions varies inversely with fluid flow from catholyte to anolyte. This concentration was also reduced with the use of precious metal coated titanium anodes.

Jan 1, 1994

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300°C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence 'on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination of H2S and uptake buildup.

Jan 1, 2003

By Konstantinos Salonitis, Joanna Mielnicka, Mark Jolly, Arun Prabhakar

Lead sheets are widely used for roofing applications, radiation protection and sound proofing. Most of the sheets are either produced by rolling cast slabs of lead sheets or via the direct method (DM) of casting of the sheet continuously. The DM method comprises of a rotating water-cooled drum that is partly immersed in a bath of molten lead and sheets are cast out continuously. The direct method of casting lead is more energy efficient compared to the rolling process which requires a casting process before rolling to achieve the required thickness. This work investigates the energy consumption in different stages of the DM process and suggests pointers for improvement. An energy audit of the process is conducted and the consumption is analysed at different stages and compared with rolled lead.

Mar 1, 2018

By Edmundo Manilla, Merete Tangstad, Daniel Davila, Eli Ringdalen

FeMn alloys are typically produced with lumpy ore or sinters. Minara Autlan, the Mexican FeMn producer, is however making Mn-nodules as a raw material for Mn-alloy production. The Mn nodules have been characterized by XRF, XRD, by wet chemical methods and by EPMA. The Mn/Fe ratio is somewhat lower compared to commercial Mn ore on the marked. The basicity of the ore is however close to 1, and additional fluxes may not be used. The Mn-nodules will be in a state of manganosite (MnO), tephroite ((Mn, Ca)2SiO4) and galaxite ((Mn,Mg)Al2O4). This leads to a low melting temperature area. A low porosity and low amount of higher Mn-oxides gives a high thermal strength to the nodules.

Jan 1, 2016