Search Documents

By J. Alberto Vázquez M.

A sensor employing yttria-stabilized zirconia (YSZ) was used to determine the oxygen activity of molten copper at laboratory scale at temperatures of 1200° and 1300 dc. The reference electrode was a Ni-NiO mixture. The amount of the deoxidizing agent (CU3P) ranged from I to 3% of the mass of copper. Thermodynamic analysis of the Cu-O-P liquid system was carried out to predict the required deoxidizing agent and the final composition of the molten copper. Both results, calculated and experimental, show that the oxygen removal is more efficient at lower temperatures. The kinetics of the deoxidizing reaction is very fast in the first minutes of the treatment. A metalography analysis of rapid cooled samples show the oxygen and phosphorus distribution

Jan 1, 2003

By W. G. Davenport

H20 is present in many flash furnace inputs. Examples are: (a) moisture in concentrate and flux (b) humidity in blast (c) moisture in hydrocarbon fuel, particularly coal, Appendix IV. H20 may also leak into the furnace from damaged water-cooling jackets. H2O, especially that it be included H2O, exerts a strong cooling effect on the flash furnace. It is important our calculations. As will be seen from the calculations, gaseous and liquid H2O both increase flash furnace industrial oxygen and oil requirements. This is because gaseous H2O (humidity in blast) must be heated from its input temperature to the flash furnace off gas temperature. Liquid H2O must be evaporated and heated.

Jan 1, 2001

By André L. B. Bittencourt

The copper content in the waste slag represents the greatest loss in the process of Caraíba Metais' Smelter. By identifying the variables responsible for copper stabilization in the slag, a minimization on these losses is expected, producing a granulated waste slag with a copper content lower than 0.7%. Statistics resourses such as control charts, Pareto's diagram and correlations curves were applied for the data obtained in the first semester of 1992. The magnetite and the calcium oxide contents in the slag of the Flash Smelter Furnace were most prominent variables. Some operational changes introduced during and after this investigation have shown good results.

Jan 1, 1994

By A. Jakobsson

Studies of the rate of interdissolution in oxide systems in the solid state are of importance in materials processing through the powder-metallurgical route. As there is a need for following the rate of the such reactions continuously, a new method based on high temperature X-ray diffraction was developed. Mechanical mixtures of the oxides were placed in a high-temperature X-ray diffraction unit and the changes in the intensity and position of the peaks with highest intensity for both the components were followed as functions of time. A suitable theoretical model has been developed in order to interpret the experimental data and evaluate the diffusion coefficients. The method was applied in the case of the system MgO-NiO. The results obtained are compared with those obtained by another new method, based on solid-state galvanic cell technique with calcia stabilized zirconia electrolyte, developed in the Department of Theoretical Metallurgy. The advantage of the present techniques to monitor the progress of the reaction continuously make them suitable for computer control of such processes.

Jan 1, 1995

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992

By José R. Parga

In some parts of the Comarca Lagunera with population of about 2.5 million people, situated in the central part of northern México, chronic arsenic poisoning is endemic and severe adverse effects attributed to As exposure have been reported. Lifetime exposure to arsenic will develop classical symptoms of arsenic poisoning such as skin pigmentation changes, gastrointestinal disturbances and neurological changes. There are several methods available for removal of arsenic from well water in large conventional treatment plants, however a very promising electrochemical treatment technique that does not require the addition of chemicals or regeneration is Electrocoagulation (EC). The EC operating conditions are highly dependent on the chemistry of the aqueous medium, especially conductivity and pH. In this study, Powder X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Mössbauer Spectroscopy (TMS) were used to characterize the solid products formed at iron electrodes during the EC process. This study will provide an introduction to the fundamental concepts of the EC method. Finally the results of this study suggest that the presence of maghemite and magnetite particles can be used to remove arsenic (III) and arsenic (V). In the field pilot plant scale study more than 99% removal of As species from groundwater is achieved.

Jan 1, 2005

By Satu Strömberg

A single-particle laminar-flow technique was used to study oxidation of two nickel concentrates and a granulated nickel matte (43 wt% of Ni). Experimental conditions were: reaction gas from N2 to N2 + 75 vol% O2; gas preheating temperatures ranging from 500 to 1100°C. The major nickel-bearing minerals in the two concentrates were pentlandite and violarite, respectively. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology and mineralogy. Total desulfurization of the nickel concentrates was achieved under the most oxidizing conditions, while the sulfur removal from the nickel matte was not as efficient, especially with the coarse size fraction. Pentlandite-based concentrate was found to be less reactive than the violarite-based.

Jan 1, 1995

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By William A. Hockings

Methods for the measurement of liberation of finely ground iron ores are described. The general method consists of separating a sample of the ground ore into a number of size fractions, followed by measuring the liberation of each fraction. The size separation has been done using electro-formed screens of 20-, 10-and 5-micrometer apertures, and also by air elutriation. Liberation (i.e., the distribution of compositions of individual particles) has been measured by optical microscopy. A computer pro-gram was used to adjust the raw count data so that it agrees with the chemical analyses of the size fractions. Various ways of presenting the results are given, and Some applications of the results to flotation processing are discussed.

Jan 1, 1981

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By Richard D. Hagni

Microscopic examination of selected, representative, unweathered samples of Birmingham, Alabama, Silurian, sedimentary iron ores has fully revealed the nature of the phosphorous-bearing mineral grains. The grains are composed of carbonate-fluorapatite (collophane), range in size from 1 um to 2.25 mm, and exhibit varied types of intergrowth with hematite. Modal analyses conducted under cathodolumi-nescence have provided quantitative data on the a3undance of each of 15 types of phosphorous-bearing mineral grains and made it possible to assess the potential phosphorous liberation from four types of iron ore. The results indicate that 27% of the total phosphorous contained in the iron ores in the western part of the Birmingham district can be expected to be liberated by fine grinding; 60% for ores in the eastern part of the district.

Jan 1, 1982

By B. Wasmund, K. Adham, K. O'Keefe, C. Lee

"Metal chlorides (e.g. iron and nickel) can be pyrohydrolysed at elevated temperatures to yield an HCl rich off-gas and a metal oxide product. Typically, the high energy requirement for pyrohydrolysis is provided by the combustion of a hydrocarbon fuel with air. Here, it is demonstrated that the use of oxygen-enriched combustion can result in lower fuel requirements and higher HCl concentrations. In addition, the oxygen enrichment can result in a smaller volume of off-gas and thus, smaller and less expensive process equipment. This new concept can be applied to both the spray roaster (SR) and the fluidized bed reactor (FBR). Similar to the aircombustion case, the oxygen-enriched process can use a direct contact venturi scrubber, to recover energy from the roaster off gas, but at a higher efficiency. The new process also uses an absorption tower for capturing HCl from the roaster off-gas, but generates a stronger HCl solution than is possible with pyrohydrolysis in air.BackgroundIn recent years, the metallurgical industry has become increasingly involved with developing methods for extracting metals, upgrading products or cleaning metallic products by using hydrochloric acid. These applications of chloride metallurgy often result in metal chloride solutions, which should be processed to regenerate HCl for reuse, and to recover the metal value as a product or by-product oxide [2, 3, 4].The pyrohydrolysis of metal chloride solutions has been done in two types of air roasters: spray and fluidized bed. The existing roasters burn a hydrocarbon fuel in air, to provide the required energy for evaporating the feed solution and to provide an elevated temperature for the chloride pyrohydrolysis to occur, according to the following reactions:"

Jan 1, 2011

By Peter V. Barr

Despite the advent of modem firing control systems reheating furnace operations frequently allow significant thermal excursions in the discharged slabs or billets after furnace delays. Although HSM furnaces are not immune to this and other related problems, mini-mill operations are most vulnerable due to their more frequent delays and (often) less sophisticated control systems. In order to reduce these problems control systems will commonly include a thermal model, operating either on-line (interacting directly with the controller logic) or in an advisory, off-line mode. Using a new 'fast' thermal model, the paper examines the thermal response of a typical mini-mill furnace during both delays and the subsequent recovery period. A variety of firing strategies are explored and compared on the basis of maintaining thermal excursions within allowable limits for rolling. Other factors, such as the potential for overheating of billets within the furnace during delays and the overall thermal state of the furnace, are also considered in some detail. Although common practice, the use of conventional thermocouple zone temperatures for furnace control during and after delays is shown to be a dubious proposition. Keywords: Reheat Furnace, Modeling, Process Control

Jan 1, 2003

By Guangwei Wang, Changle Zheng, Yifan Chai, Jian Guo, Weiwei Geng, Jianliang Zhang

In this paper, characteristic and kinetics of CO2 reaction with four different kinds of coke such as top-loading coke, dry quenching tamping coke, wet quenching tamping coke and semi-coke were investigated based on isothermal method. Electric resistance reduction furnace was used to heat the sample. Volume Model (VM) and Shrinking Core Model (SCM) were used to calculate the kinetic parameters and to contrast with the experimental results. The results showed that the Volumetric Model (VM) was much suitable for the reaction of top-loading coke, dry quenching tamping coke and wet quenching tamping coke, while Shrinking Core Model (SCM) was much suitable for semi-coke.

Jan 1, 2015

By Claudio Parra De Lazzari

The determination of the governing step of the deoxidation rate and the effects of the hydrogen content of the mixtures (C), the diameter of the delivery orifice (4) and the Reynolds number of the orifice (Re.) on the product Av kjg were investigated. A,, is the total surface area of the interface between the bubbles and the melt and kjg is the mass transfer coefficient in the gas phase. The design of the experiments was based on a two level statistically fractionated, factorial planning. Oxygen in the melt was measured as a function of time. It was found that the governing step of the deoxidation rate was the transport of hydrogen in the gaseous phase and that {Ay kjg} increases with C, {o} and Reo.

Jan 1, 1997

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

By Burcu Ertug, Necip Ünlü

"On average, one out of two glass bottles coming on to the market is provided by recycling processes in Europe. Glass recycling has been started by the early of 1970s in Turkey, and the recycling amount has been reached to 70 thousand tons recently, while 4.2 million tons which represents only 25 percent of total glass manufactured, is the amount of glass collected annually for recycling in the world. The glass recycle process basically involves collecting, sorting, then crushing and grinding after which glass cullet is produced as the secondary raw material. Removing of the contaminants from the glass cullet, and then melting are the next steps. In this study, recent developments of 100% recyclable without any deterioration in quality, and never decomposable glass, are discussed detailed in terms of glass production processes.1.IntroductionIn many countries, waste glass constitutes a large proportion of solid wastes, and recycling the glass is a major environmental problem all over the world [1]. Among the diverse types of waste, glass is one of the most valuable recycling materials because it can be revived and recycled completely and hardly decomposes [2]. Between 80% and 85% of the mass output from the worldwide glass industry is either in the form of containers for the food, beverage, and pharmaceutical industries, or flat glass for building construction or for motor vehicle manufacture. Other product segments, whilst only constituting about 15% of the mass output, produce high value technical and consumer products by comparison with container and flat glass [3].In the present study, the recycling of Liquid Crystal Display (LCD), Cathode Ray Tubes (CRT) and Printed Circuit Boards (PCB) were examined. The production of glasses and glass-ceramics from glass cullet, synthesis of different compounds from recycled glass were other subjects of interest. The use of recycled glass for construction industry and using glass as aggregate were emphasized. Finally the recovery of glass fibers were investigated."

Jan 1, 2012

By Dewei Zhu

A general purpose computer model for describing the transport phenomena and resulting rate of deposition in Chemical Vapor Deposition (CVD) processes has been described. Partial differential equations describing the conservation of mass, momentum, energy and chemical species are solved by a computer program employing a finite volume method. The program allows for multiple chemical species and natural convection effects. In this paper, the deposition of silicon by the reaction of silicon tetrachloride and hydrogen in a vertical stagnation flow reactor with rotating substrate has been considered. The effects of reactor pressure and substrate rotation speed on the rate and uniformity of deposition have been studied. The predicted rates of silicon deposition along the substrate are in reasonable agreement with experimental results found in literature. The model can be used as a tool for design optimization of such reactors.

Jan 1, 1990

By S. K. Wu, Ray Y. Lin, Sunil Annaji

Infrared joining of TiAI using aluminum foils as the filler material was investigated at temperatures between 1050 °C and 1350 °C in a flowing argon environment for times varying between 15 and 60 seconds. Using aluminum foils, the attempt was to form the Al3Ti phase in the joint as a result of reaction between Al and TiAI at temperatures above the melting point of Al. It has been found based on X-ray diffraction and TEM analysis that, Al3Ti, indeed is the product of infrared joining of TiAI using Al as the joining alloy. Al3 Ti was detected even in the joint processed at 1050 °C for only 15 seconds. Since the aluminum foil used in this study contains 27 at% Si, the t 2 phase in the Ti-Al-Si ternary system is believed to have also formed at the joint/base TiAI interface. Cross sectional studies on the joined specimens have shown different degrees of reaction depending on the temperature and time of joining. Micro hardness evaluations across the joint show that the hardness near the center of the joint is typically smaller than that near the joint edge next to the base material. However, as the joining temperature and time increase, the increment of the hardness at the center of the joint is faster than that around the periphery of the joint.

Jan 1, 1996

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993