Search Documents

By V. Vergara

Four copper composites were obtained by mechanical alloying, using as dispersed phases of four carbide powders; they were: boron carbide, chromium carbide, silicon carbide and zirconium carbide. The purpose of this work was to study some characteristics of these compounds and their feasibility for use as materials for electrical equipment. Raw materials used were copper powder finer than 150 mesh, and 2-4 vol % of powder carbides finer than 325 mesh. The alloying process was carried out using both a Spex 800-D mill with tungsten jars and balls and a hardened stainless steel jar and balls, the purpose of which was to measure the degree of contamination induced by the milling media. The changes in particle size, morphology and microstructure of copper alloys were studied with SEM and TEM for each alloyed powder. The degree of saturation of copper by the carbides was measured by X-ray diffraction. Sound samples were obtained by hot isostatic pressing at 1073°K. The best characteristics were obtained for the compound copper-chromium carbide, based on their hardness, tensile strength and electrical conductivity values. The other alloys failed due to their excessive brittleness after hot pressing.

Jan 1, 1999

By José Palacios, Mario Sánchez, Fernando Parada

As an alternative method of reducing the large amount of slag generated during metallurgical processes in the primary copper production, it is to use the remaining iron in the slag as feed material for the iron and steel industry. The slag is generated during copper concentrates smelting in ratios ranging from 2 to 5 ton per ton of produced copper, and it contains 42–45% of iron. However, copper, sulfur and other detrimental elements affecting iron properties need to be reduced prior to use the slag in steel production. Therefore, some laboratory experimental run has been conducted to reduce copper by slag oxidation followed by leaching and recovering the dissolved copper by SX-EW, and smelting the solid with coke to produce a metallic phase containing 98% iron and 0.9% molybdenum. In further reducing steps, copper content is lower down and a molybdenum rich iron phase is obtained. Recovery of iron from copper slags considering reduction and control of harmful elements for iron properties was studied.

Mar 1, 2017

By Masao Suzuki

Over 5 million cars are scrapped yearly in Japan. After dismantling. scrapped automobiles, they are put into a shredder for differential recovery of ferrous and nonferrous metals. The residue, which is called shredder dust, runs over 1.2 million tons per year. This paper reports a entire sequence of scrapping. cars. in Japan with the following sections: (1) production and scrapped car management, (2) material composition, (3) dismantling, (4) shredder plant, (5) differential recovery of metals including specific gravity separation and newly developed color separation.

Jan 1, 1995

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By Dong Liu, Zejian Yang, Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"The structure, composition, morphology, and adsorption property of UV-vis light of as-prepared samples were characterized using XRD, SEM, FTIR-EDS, and UV-vis DRS. UV-visible light induced photocatalytic degradation of methylene blue ~) over Ti02-doped diopside was investigated. Experimental results show that doping Fe + induced the formation of Ti-0 or Ti-0-Si in diopside, and promoted the light adsorption property of diopside. Photocatalytic reactivity of Ti02-doped diopside obviously depended on content of doping Ti02. The diopside with 3% Ti02 exhibited the superior photocatalytic activity with 76% degradation of methylene blue under light irradiation for 3 h.IntroductionPhotocatalytic technology has been extensively studied in the process of dealing with inorganic and organic pollutants. Ti02, with its own non-toxic, stable, low-cost and other advantages, has become the most widely studied photocatalytic materials[l-SJ_ The low utilization quantum made it restricted in the practical application. SrTi03 as the representative of the perovskite[9·121, Bi2W06 for the composite oxide[13,141, also attracted wide interest in the photocatalytic studies. However, these photocatalytic material has been mostly prepared in relatively strict experimental conditions with chemical reagents, they had small production, high cost, which made them difficult for practical applications.In our country, there has 400 million tonnes of ti-bearing blast furnace slag (TBBFS) each year in the process of smelting pig iron, which has lead to waste of titanium resources and pollution of the surrounding environment. In recent years, studies have shown that TBBFS instead of pure Ti02 to be photocatalytic materials is feasible[ 151. TBBFS has not only been higher photocatalytic degradation activity for the o-nitrophenol, methyl orange, nitrobenzene and other organic matter[16-191,but also exhibited excellent in the process of dealing with inorganic heavy metals in waste water (containing Cr6+i201. If TBBFS can be successfully applied to photocatalytic technology, the will make large accumulation of titanium-bearing slag reasonable used, so as promote the re-use of energy. At present, our understanding of the photocatalytic activity of TBBFS is steadily deepening. Photocatalytic activity ofCaTi03 has been reported as one of the main minerals ofTBBFS [21'21J, However, there were few studies for Another major mineral of TBBFS - diopside which had the content of9-15%. diopside would doped with Ti02 In the process of smelting pig iron, therefore, Ti02-doped diopside's photocatalytic activity in the UV-Vis was mainly studied in this paper."

Jan 1, 2013

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By J. D. Zhu, T. Ohmichi, H. Yasuda, S. Kashiwai, I. Ohnaka

"Since the casting process affects the properties of castings, its computer simulation has been greatly developed in the last decades. This paper presents our recent works, especially on mold filling simulation, because most casting defects such as porosities and inclusions that greatly affect the properties originate during mold filling. The first topic is the mold filling simulation with consideration of cavity pressure change during mold filling, including direct observation of flow phenomena with X-ray and pressure measurement. The second .one is the mold filling simulation in the lost foam process, in which gasification of polystyrene pattern and gas outflow through the coating and mold have been considered. The simulation can predict not only the mold filling sequences but also periodical vibration of the gas layer between the melt and pattern. The third one is the comparison of simulation of Al melt flow in a metallic runner and direct observation through a transparent mold, showing that the entrapped gas or inclusions is expelled ahead through the melt and its simulation needs very fine meshes. These examples show that the comparison of simulation and observation is very important to develop the numerical simulation further.IntroductionThe mechanical properties of castings are greatly affected by casting defects such as porosities and inclusions, and solidification structure. Although recently the structure simulation has greatly progressed [1-4 ], the application in plants is very limited, because the structure is mostly determined by chemical compositions and cooling rate, enabling us to estimate it from the structure of past similar castings without simulation.On the other hand, the casting defects often vary with each casting or time. Among the defects, porosities and inclusions are main causes to deteriorate the properties and mostly originate during mold filling. Therefore, a lot of efforts to simulate the mold filling and estimate those defects have been made in the last decades [l,5,6]. These efforts have been mostly to develop numerical techniques to solve the Navier-Stokes equation. However, the flow phenomena in molds have not been well understood, because the direct observation of the flow phenomena in mold is not easy. This means the accuracy of the simulation is still not clear."

Jan 1, 2000

By Wenqiang Bao, Qijie Zhai, Ting Wang, Shaobo Zheng, Huigai Li

The type of inclusions with different sizes in as-cast low carbon steel strip which is deoxidized by Si–Mn has been characterized by scanning electron microscope (SEM) and transmission electron microscopy (TEM). SEM observation and analysis suggested that the type of inclusions larger than 1 μm is manganese silicate. TEM analysis was carried out to investigate the composition and structure of nano-inclusions. Inclusions with diameter about 100 nm are manganese silicate, MnS–Si(Mn)Ox complex particles and isolated cubic Al2O3. Furthermore, HREM observations have revealed that there were two kinds of ultrafine particles in size range of 5–10 nm. One is spherical monoclinic Cu2S; the other is silicon-iron oxide particles with morphology of long strip. In addition, some thermodynamic calculations were performed to explain the corresponding relation between the type of inclusions and their size.

Mar 1, 2017

By Olga K. Karakasi, Angeliki Moutsatsou, Ioanna Kavallari

"The present study focuses on the amelioration of the behaviour of high calcium fly ash (HCFA), investigating its application in a new environmental field: oil spill clean up. High calcium fly ash is a by-product of electric power plants, produced annually in large quantities, whose greater amount is landfilled. Some of its properties, such as its chemical and mineralogical composition, its fine particle size, its porosity, floating ability and hydrophobic character make it an attractive material for this purpose. Researches showed that when added to an oil spill, it forms a semi-solid phase, which allows the quite total removal of the oil, but it is not stably retained on the surface. In order to ameliorate its floating ability, the decrease in its specific gravity by mixing with a lighter material is investigated. In the present study the mixing with two materials, already used in oil spill clean up, sawdust and a polymer, has been examined. Addition of 15-25% w/w sawdust to HCFA results in a material with better performance than HCFA or sawdust alone: it has a satisfactory floating ability and allows total removal of oil. Addition of the polymer, however, has resulted in no significant amelioration of the oil sorption behaviour of HCFA, probably because no affinity between HCFA and polymer has been achieved.IntroductionCoal fly ash is a by-product of coal combustion in electric power plants, produced worldwide in huge quantities, approximately 500 million tones annually. High calcium fly ash (HCFA) is classified to class C presenting a (Al2O3 + SiO2 + Fe2O3) > 50%. The production of lignite fly ash in Greece comes up to 13 million tones annually, of which only 12% is used in construction applications, the other being landfilled [5, 6].Besides its limited application worldwide as a construction material, research is focusing on the development of new environmental applications, such as waste stabilisation and solidification, soil and water environmental improvement [9, 12]. For the application of fly ash in further environmental fields several chemical modifications have been applied, in order to improve its properties. Extensive research has been focused on the conversion of both coal and lignite fly ash to zeolite and its further application in environmental field, such as the uptake of inorganic (heavy metals and ammonium [8, 11]) or even organic compounds (methylene blue [15]) from waste water streams, or the use as molecular sieves, to adsorb water molecules, SO2 and NH3 from gas streams, due to the high cation exchange capacity and porosity of the produced zeolithic material. Furthermore, lignite fly ash has been combined with sodium silicate solution, prepared by treatment of rice husk ash, and tetrapropylammonium bromide, to synthesise hydrophobic zeolite ZSM-5 [4]."

Jan 1, 2008

By Xiaolong Lin, Yuanbo Zhang, Tiancheng Nie, Guanghui Li, Zhizhong Li, Zhiwei Peng, Tao Jiang

The coal-based direct reduction process has gradually become the focus of research concerning direct reduced iron production due to its advantages, including high reduction rate, stable chemical composition, and good metallurgical properties of products. Based on coal-based reduction theory and briquetting technique, this paper reports the use of microwave energy for intensifying the reduction of carbon-containing briquettes mainly consisting of magnetite concentrate and biochar. The heating behaviors of the raw materials show that under the conditions of microwave power of 1250 W, N flow rate of 4 L min −1 and briquetting pressure of 400 N, the briquettes present the highest heating rate. The average heating rate reaches 35.16 °C min −1. When the briquettes are irradiated by microwaves at 1050 °C for 45 min, the metallization degree of the reduced briquettes reaches 93.58%.

Mar 1, 2017

By Jing Zhan, Tian-zu Yang, Wei-feng Li, Li-Hua Jiang, Shi-yan Xu, Jian-yang Huang, Chuan-fu Zhang, Yan-qing Fan

The amount and activity of coal, reduction temperature and other parameters of the process of bottom-blown reduction of liquid high lead slag were investigated in laboratory. Methods to strengthen the bottom-blown reduction process were studied by industrial production. The results were in the follows: the reduction temperature was 1150℃; reduction time was 1.5h; the reductant was anthracite; lead content in slag was controlled to 2%; the rate of coal was 7% and gasification loss of coal in high temperature was severe; liquid lead slag reduction rate was faster with coal; prolonging the reaction size had little effect on reducing lead in slag; the size of the reactor can be further reduced.

Jan 1, 2015

By XUEWEN WANG, Xingming Wang, Xuehui Liu, Mingyu Wang

The Panzhihua titanium concentrate contains high contents impurity of Mg and Al, and it is difficult to prepare high grade titanium slag. To solve this problem, a sodium salt roasting-acid leaching process was proposed for removing the impurities in titanium concentrate. Na2CO3 and titanium concentrate were mixed with the proportion of 1:4, and then the mixture was roasted at 700 for 2h. After roasting, the calcine was leached with HCl solution. The experimental results showed that the removal rate of silicon and aluminum can reach more than 85% and 80%, respectively, at leaching temperature of 70 , leaching time of 4h, HCl addition of 5ml and liquid-solid ratio of 4:1.

Jan 1, 2016

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By K. Fukushima, K. Baba, H. Kurokawa, M. Yamagiwa

"The Toyo smelter has expanded its anode production capacity from 126,500 to 239,000 t/year by introducing technical oxygen into blast air for flash and converter furnaces and improving smelting facilities. Significant efforts were made in the expansion not to increase the number of workers, which mean development of some automation systems for the copper converters and anode casting wheel. The efforts have resulted in the above-mentioned increase in productivity and a saving of production cost as well as a decrease in the number of workers for the anode casting operation.IntroductionThe Toyo smelter has been performing a highly stable and pollution free operation since its commencement in 1971 (1). Its distinctive features are the on-line control by process computer (2) and the high productivity without trouble. But owing to the so-called oil crisis in 1979, we were faced with a sharp increase in production cost. To decrease the production cost, some measures for saving of energy were planned and carried out, such as conversion from oil to coal in a flash furnace (3), the heat recovery from converter slag and the introduction of technical oxygen in blast air with the intention of energy saving as much as possible.The first increase in production capacity and some savings of production cost were attained in 1982 by the introduction of technical oxygen in blast air for the flash furnace without major modification of the furnace as shown in Table I. The capacity of an oxygen plant is 7,800 Nm3/H as 90% O2 . Part of oxygen from the plant is also supplied to tuyeres of copper converters through an oxygen holding tank with a volume of 830 m3 at 7 kg/cm2-G."

Jan 1, 1989

By E. Daniel Baker

"The term ""oxide disseminated gold deposits"" refers to near surface, gold-bearing veins, faults, and shear zones that typically contain appreciable amounts of oxidized ore or gossanous material, resulting from oxidation of sulphides.The concept of oxide gold deposits underwent a dramatic change after the discovery of the Carlin gold mine in north-central Nevada in the early 1960's. Now the term implies large tonnage, low-grade bulk minable deposits that are processed by milling and/or heap leach methods.Oxide gold deposits may now be classified into two types: (1) primacy ores derived directly from the effects of hydrothermal alteration on host rocks, and (2) secondary oxide ores derived from the supergene oxidizing effects of circulating post-mineral meteoric waters on gold-bearing sulphides. Each type of deposit has unique diagnostic mineralogic and metallurgical characteristics that must be addressed to achieve successful exploration strategies and viable metallurgical exploitation.The author would like to thank the management of Newmont Metallurgical Services and Newmont Mining Company for allowing presentation of this paper. Thanks are due Sevkett Acar, Donald M. Hausen, Jerry R. Odekirk, and D. Erik Spiller for their critical review of the manuscript. Also, thanks are extended to all those cited and uncited whose hard work and dedication have led to the discovery and exploitation of near-surface oxide gold deposits. Our knowledge would be greatly limited without the dedication and research of many others."

Jan 1, 1997

By E. Kuzeci, R. Kammel

"Lately various voltametric methods have gained increased attention as an analytic tool in hydrometallurgy. Voltammograms with mercury drop electrodes or glassy carbon electrodes provide information about the electrocrystallization of cathodic deposits and allow calculation of kinetic data by means of characteristic parameters like the peak potential and peak current and their variation with the voltage scanning rate.Cyclic voltammograms are also suitable for identification of reaction sequences. Voltammograms with carbon paste electroactive electrodes containing metal sulphide additions reveal information about the dissolution behavior. The stripping voltammetry can be applied to analyze metal ions and organic additives (e. g., thiourea) in extreme low concentration. Typical application of the various methods studied with microcomputer controlled measurement system are explained by examples selected from copper hydrometallurgy.IntroductionThe use of electroanalytical methods in metallurgical process control can be dated back to the starting period of industrial copper refining, when the deposition of the metal ions was followed electro-gravimetrically by weighing the electrode with deposits (1). The principles of metal deposition and dissolution have not changed but the methods to follow these phenomena were subjected to noticeable developments and especially the introduction of polarographic investigations by Heyrowsky (2) has greatly contributed to the progress in electro-analysis. A review about the fundamental work on the electrochemical kinetics in earlier time is compiled in a monograph of Vetter (2). With the steady improvements in the instrumental techniques, it is nowadays possible to apply several current and potential modulations for measurements with improved selectivity and sensibility. There is however, still a lack in theoretical interpretation of the data obtained. More theoretical information are already available for linear voltametric methods for systems where reduced as well as oxidized species are dissolved in the electrolyte (4, 5). Some recent investigations have also shown the reliability of these techniques to study electro-crystallization (6, 7). Main fields of the application in the hydro - and electro-metallurgy are:"

Jan 1, 1989

By Hu Meilong, Liu Lu, Bai Chenguang

Extracting perovskite from high titanium-bearing blast furnace (BF) slag is a green and potential method to recover the second titanium resource. The non-isothermal crystallization process of perovskite in synthesized high titanium-bearing slag was studied in situ by confocal scanning laser microscope (CSLM) with cooling rate of 20 K/min. The results showed that perovskite was the primary phase formed during cooling process in the titanium-bearing synthesized slag (TiO2=23%). Perovskite started to precipitate at 1719 K and finally presented an orthogonal straight lines morphology.

Jan 1, 2014

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011