Search Documents

By Jian Yong Chen

The results of a laboratory investigation of pullout tests conducted on grouted, plain cable bolts are reported. The main purpose of the study is to determine experimentally the shear bond stiffiess of cement grouted and resin grouted cable bolt systems, which is an important input parameter for numerical modeling of cable bolt support. Three nominal embedment lengths of 152mm (6 inch), 203mm (8 inch) and 254mm (10 inch) were used and two types of grout namely cement and Anchortite resin were used. Two water- to-cement ratios of 0.3 and 0.4 were employed for the cement grout. The concepts of effective shear stress and effective shear stiffiess are explained and adopted to calculate the shear bond strength and the elastic shear bond stiffiess per unit length. A comparison of results with previous research is presented to reveal the effect of water-to-cement ratio and embedment length on the shear bond characteristics of grouted cable bolts.

Jan 1, 2005

By Behdeen Oraee-Mirzamani

Tunnel stability has an important role in the production process of an underground coal mine. There are various methods for analysing tunnel stability, such as numerical methods and analytical methods. In this paper, numerical methods (Phase2 software) have been used to determine tunnel wall displacement in a mining tunnel of the Parvade underground coal mine. The Ground Reaction Curve has also been drawn using analytical methods to determine tunnel wall displacement. The comparison of results from the numerical method and the analytical method show a noteworthy difference in the tunnel wall displacement. The displacement calculated by the numerical method shows a lower value than that of the analytical method because the numerical method is more suited to modeling the various coal and rock layers, as well as the shape of the excavations found in coal mines. The methodology used in this paper together with the results obtained from both methods can serve as useful tools for the coal mine design engineer when determining the ground support requirements.

Jan 1, 2013

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By Thomas W. McClain

This paper describes the importance of considering ground control measures when importing U.S. continuous mining technology in foreign countries. Important ground control factors are discussed. Each year the USA exports a significant amount of continuous miner equipment (i.e. continuous miners, roof bolters, coal haulers, shuttle cars, continuous haulages, scoops and feeder-breakers). International customers see the opportunity to significantly improve their productivity and increase their longwall gateroad development rates by implementing the room-and-pillar (place changing) mining systems used throughout the USA. However, a number of issues are often overlooked or not thoroughly evaluated when selecting the equipment, often resulting in lower than expected productivity. Ground control is one of the critical factors that must be addressed. Since 1993, the author has assisted numerous international customers and manufacturers with implementing or improving the performance of continuous miner and room-and-pillar systems in Australia, India, Mexico, South Africa, and the United Kingdom. An essential first step is to conduct a thorough ground control study, and then integrate its findings into mine layout, equipment selection and section operating plans. Based on actual case histories, the author will present a number of examples and "Do's and Don'ts." Another key to success is the involvement of manufacturers and suppliers with customers when implementing new systems and technology. The importance of allowing for cultural evolution by both management and workers for acceptance and successful implementation of any new system is also discussed. Over the past ten years, the global coal industry has gone through some very dramatic changes. Countries that previously experienced a freight advantage, such as Australia shipping coal to Japan and Korea versus the United States, are finding they are now in a world coal market similar to other commodities and products. Today, coal prices arc stated F.O.B. at the consumer, and the origin is often irrelevant. Also, previously state-run coal industries have been privatized, such as the United Kingdom, and others such as Poland and India are currently going through the same transition from state-run to the private sector. In all cases, the key to continued viability, or survival, depends largely on reducing costs in order to compete for a market share. Two ways exist to reduce costs. First, almost everyone tries to reduce expenditures. Depending on the circumstances at a given mine or in a specific country, this helps to some point. However, most find that secondly, production must be increased to achieve the necessary cost reductions to compete in today's global coal market. As a result, over the past ten years, foreign companies and countries have looked to the USA for new mining methods and systems to significantly increase productivity. Thus, a major portion of American equipment manufacturers and suppliers sales have been exports, which has played a major role in helping to "keep-the-doors-open" for a number of companies through the lean 1990's, when American coal companies were postponing capital expenditures and expansions. As foreign companies and countries have looked to the USA for ways to improve productivity, they have become particularly interested in continuous miner equipment systems and most often "room-and-pillar," "bord-and-pillar" or "place changing" mining systems for four reasons. First, in countries such as the United Kingdom and Germany, who have been longwall mining for generations, there remain numerous remnant small pockets of reserves in existing mines that are either too small or too difficult to longwall mine, and are conducive to the flexibility of continuous miner systems. Second, for countries such as Australia, who have experienced the constant problem of developing longwall gateroads in a timely manner to avoid longwall move delays, new or alternate methods are required. Third, companies and countries using roadheader machines on coal production are recognizing the increased productivity potential of continuous miner equipment. Fourth, countries such as South Africa and India, where a substantial amount of the production comes from conventional mining methods, "drill-and-blast", companies are recognizing the opportunity to improve by implementing continuous miner technology. Colliers & Associates, Inc. has found that over the past eight years too often foreign companies or countries purchase American continuous miner equipment without first conducting a thorough geologic, geotechnical and ground control study for the reserves to be mined. The problems are compounded by not developing mine plans, and submitting them to the regulatory authorities for approval prior to purchasing and even implementing the equipment.

Jan 1, 2001

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

By Don Berger

Highwall scaling, bolting and technical blasting are important aspects in the remediation of existing highwall exposures. Proper planning, design and research are important first steps in the development of long term stability. Research into old workings and their influence on highwall stability control the planning and design. These steps are followed by improvements in blasting techniques, highwall monitoring programs and constant evaluation of the results. Recently, due to a number of factors, the highwalls of the Open Cut Mine have started to deteriorate, creating both operational and potential safety problems. Geologic setting, highwall design, mining operations, old workings and weather have combined to create adverse conditions that have allowed sections of the highwalls to become unstable. Homestake Mining Company has developed a program to alleviate the existing ground control problems and to decrease the effect operations has on future highwall stability.

Jan 1, 1996

By Shugang Li

The layout and efficiency of the degasification system is heavily dependent on the distribution of and the methane migrating mechanism in the mining induced fractures in the overburden strata In this paper, physical modeling and numerical simulation are employed to study the mining-induced fracture zones and the stress distribution in these zones. The physical models show that both the fracture and compaction zones form a parabolic shape in the over- burden strata along the panel transverse direction. When this is generalized to the panel longitudinal direction, the shape of the mining induced fracture zone over the longwall gob can be represented by a 3-D elliptic paraboloid function. Through the observation of bed separation, fracture density and distribution pattern in the physical models, it is believed that the development of the parabolic fracture zone can be divided into three distinguishable phases. The expansion characteristics and sizes of the fracture zones can be estimated. The numerical stimulation studies can be used to estimate the extent of the stress release zones. The stress release zones can be also divided into a high compressive stress - fracture closure zone, stress relieved - fracture expansion zone, and intact zone. The methane desorption model is then used to analyze the methane migrating pattern in the fracture zone. The developed model has been verified by the results of a longwall gob degasification tests at a coal mine in Yangquan, China with a fair agreement. Such studies show that the model can provide a reasonable accurate tool for designing the gob-well degasification system for longwall mining operations.

Jan 1, 2005

By Denise Müller, Axel Preusse

"Due to multilateral underground use, mining subsidence is discussed more and more with regard to issues other than mining, such as post-mining topics, storage, or geothermal use. These discussions and the influence of the energy policy is why the situation in Germany is described as a transition from active to abandoned mining. Many PhD theses have been written within the last 20 years—every single one with a different topic but all with the same issue—the effects and challenges of mining subsidence.These challenges start with the research regarding geological and hydrogeological conditions, which is the basis for calculations like the angle of draw or predictions of subsidence due to water table drawdown. Furthermore, the research investigates issues like risk-management and financial planning. One of these issues is post-mining calculations; others include potential hazards of storage or the use of geothermal energy.This paper outlines an overview of German mining and the consequences due to subsidence. It deals with an overview of the circumstances related to hard coal mining, lignite mining, the use of geothermal energy, gas, and opportunities regarding underground storage. Basically, it describes the essential steps of processing mining subsidence, starting with monitoring to forecast and up to safety measures.With a glance back to the applied research of the prior two decades, we compare given forecasts with experiences already gained.Even though mining decreases, ground control does not.INTRODUCTIONAfter the Second World War, an economic recovery started in Germany, during which the mining industry provided an advantage. Areas like the Ruhr District or Saarland were characterized by hard coal mining. In addition, there was lignite mining in the Rhenish mining area and the middle German coal district. In the Lausitz area, there were gravel and sand companies for the construction industry and many other medium-sized mining companies. Especially in the Ruhr District and in Saarland, where large coal fields were built, mining played a major role. The number of mines increased, and the negative effects on the terrain got bigger. While minor open pits or quarries have influences on the landscape only, large open pits and underground mining lead to significant ground movements. This results in a larger importance of mining subsidence engineering. Calculations of subsidence and forecasts have been developed and refined within the last several years. Due to the fact that the mining areas were and still are densely populated, the forecasts are getting more and more precise."

Jan 1, 2018

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By Elizabeth Holley, Meriel Young, Gabriel Walton

"The coal mine roof rating (CMRR) was developed by Chris Mark and Greg Molinda to bridge the gap between geological variation in underground coal mines and engineering design. The CMRR accounts for the compressive strength of the immediate roof, the shear strength and intensity of any discontinuities present, and the moisture sensitivity of the immediate roof. The CMRR has been widely used and validated in Eastern US coal mines, but it has seen limited application in the Western US.This study focuses on roof behavior at a Western coal mine. Mine A shows significant lateral geological variation, along with localized faulting and a laterally extensive sandstone channel network. The CMRR is not used to predict roof instability at the mine.It is, therefore, hypothesized that there are other factors that are correlated with roof instability in underground coal mines that could potentially also be included in the CMRR.This hypothesis was tested by collecting 30 CMRR measurements at Mine A. At each measurement location, a binary record of the roof condition (stable or unstable) was made along with parameters, such as depth of cover, thought to also correlate with roof stability. A statistical analysis of the data was performed to determine the parameters in addition to those included in the CMRR, which can be correlated to roof stability.INTRODUCTION AND BACKGROUNDRoof fall is one of the greatest hazards facing underground coal miners (Barczak et al., 2000). In 2017, 91 lost-time injuries occurred due to roof fall in US underground coal mines. A further 48 roof falls occurred with no lost days (MSHA, 2018).The coal mine roof rating (CMRR) classification was developed by Molinda and Mark (1994) to quantify the geological description of mine roof into a single value that could indicate mine roof stability and be used in engineering design. It is widely used in the Eastern US as an input for the analysis of longwall pillar stability (ALPS) in underground coal mines. It provides an excellent start; however, it is arguably not fully comprehensive, nor is it widely used in the Western US."

Jan 1, 2018

By Russell Frith

Probably the most expensive but least well understood roof falls in underground coal mining, are those that occur ahead of the powered supports in the centre of longwall face. Even small roof cavities result in the dilution of the ROM product and large cavities can stop the face for days if not weeks and the incurred cash flow losses can be catastrophic. Expensive and time-consuming remedial measures (e.g. PUR, cavity filling, removal of stone from the AFC by hand) are required and equipment wear and damage can be significant when the need to blast and convey stone is also considered. Through four major research projects within the Australian coal industry and numerous consulting assignments, the author has spent the best part of fifteen years attempting to identify and defme the various geotechnical and operational factors that determine whether a major roof cavity occurs ahead of the powered supports or a normal goaf fall occurs just behind them, the difference in operational outcome being enormous. The paper presents a condensed summary of the overall technical findings covering such issues as roof fall mechanisms, the measured influence of cover depth, periodic weighting of massive strata units and its quantification, the role of cut-throughs in chain pillars, face width and height, the role of the powered support and the influence (both positive and negative) of mine site operations. The big picture outcome is the view that high production longwall extraction is well-suited to certain geotechnical environments, is marginal in others and under certain conditions is fatally flawed and beyond the control of mine operators, although fortunately the latter category is a relatively rare situation. Various risk-based research findings in this regard will be given as a basis for future discussion.

Jan 1, 2005

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By Yang Li

For the study of overburden movement in longwall mining of shallow coal seams, most scholars merely consider the thickness of bedrock and top soils. In this paper, the overburden movement in longwall mining of shallow coal seams with thin top soils and key strata group was studied. By using numerical simulation, the development of fractures in the overburden was analyzed for different ratios of panel width to depth (W/D) and depth to mining height. The results show that the overburden movement changed with the variation of mining height, panel width and depth under the specific geological conditions. It also explain how different overburden disturbance structures, such as ?three zones? (caved, fractured, and continuous deformation zones), ?two zones?(caved and fractured zones) or ?steps-like collapse? are formed under different mining conditions. The results broaden the vision for research on overburden movement in longwall mining of shallow coal seams.

Jan 1, 2014

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Saeed Zhandi, Behdeen Oraee

"Rock bursts remain an important problem in longwall coal mining. These bursts are due to a sudden and severe failure of rocks from a high stress concentration in deep underground excavations that occur with the instantaneous release of strain energy stored in the rocks. They can potentially cause irrecoverable damage to equipment and personnel, thus accurate rock burst prediction and control is expected to be carried out by the mine design engineer. As a result, this can constitute major challenges for said engineer. In this paper, forensic engineering has been used to evaluate the possibility and extent of rock bursts in deep coal mining. For this purpose, established mining engineering principles, including factors influencing the severity of rock bursts, have been incorporated in the forensic engineering technique. The analyses took place in five steps:• Assessment of regional and local conditions prior to the event• Assessment of conditions after the event• Hypothesize plausible ways in which pre-event conditions can become post-event ones• Search for evidence that either denies or supports various hypotheses• Apply engineering knowledge to relate the various facts and evidence into a cohesive scenario of how the event may have occurred.The paper concludes by demonstrating a method for predicting rock bursts and preventing their reoccurrence. The methodology used in this paper, together with the results obtained, can serve as useful tools for the coal mine design engineer in the primary evaluation of rock burst potential in underground coal mines.INTRODUCTIONA rock burst is defined as the sudden and great failure of rocks due to a high stress concentration in deep underground mines. This phenomenon occurs with the instantaneous release of strain energy that is stored in the rocks, and can cause irrecoverable damages to both equipment and personnel (see Figure 1). Rock bursts pose a hazard owing to their lake of predictability; in fact, research into understanding rock burst mechanics and implementing techniques for their monitoring and prediction has been taking place for over 50 years."

Jan 1, 2015

By Kevin Andrews, Scott Nelson, Terry Hamrick

"In the process of Geologic Hazard Mapping (GHM) for underground coal mining, geologists evaluate the effects of various geologic and geotechnical conditions to assist with optimization of mine productivity and with selection of more favorable areas for future development. The methodology involves correlation of multiple geologic factors (such as overburden depth, proximity to sandstone channels, and areas with weak immediate roof strata) with conditions encountered during mining (roof falls, floor heave, pillar spalling, etc.). Such studies yield maps that identify areas where mining is likely to be difficult and allow mining engineers to foresee favorable and unfavorable mining areas when planning new or expanding mines. To expand the benefits of GHM, work has been done to correlate geologic factors with room-and-pillar mining advance rates. Average mining advance rates are mapped and then correlated to different areas, as characterized by GHM. This process exposes the geological characteristics that have a material impact on mining rates of advance, improving the rates of advance into future mining areas with similar geological conditions. The final result of the work allows mine planners to not only design the mine qualitatively accounting for areas of unfavorable conditions, but also allows the mine planner to more accurately apply rates of advance for mine timing and production sequencing. The use of GHM to predict mining advance rates in unmined areas enhances the benefits of traditional hazard mapping and provides quantitative data that can be incorporated into mine sequencing models.INTRODUCTIONThe role of a geologist in the coal mining industry has evolved significantly over the last 30 to 40 years. Geologic Hazard Mapping (GHM) mapping for coal mines began in the late 1970s and early 1980s (Chase, Newman, and Rusnak, 2006). Since its beginnings, the GHM process has evolved significantly and continues to take on new levels of sophistication. Numerous case studies of GHM application to predict future mining conditions exist in the literature. For example, Artrip, Nelson, and Newman (1993), documents the geotechnical characterization of roof and floor for mining in the Imboden Seam in Virginia where previous mining efforts had been abandoned due to adverse mining conditions. In addition, Keim and Miller (1999) summarize evaluation of geological influences on a longwall mine in West Virginia. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed."

Jan 1, 2018