Search Documents

By Pierre-Yves Declercq, Andre Vervoort

"After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement. Although most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated. After the closure and flooding of underground excavations and surrounding rock, this movement is reversed. This paper focuses on quantifying the upward movement in two neighboring coal mines (Winterslag and Zwartberg, Belgium). The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar (INSAR). The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average. The upward movements are not linked directly to the past exploitation directly underneath a location. The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings. Local features, such as geological faults, can have a secondary effect on the local variation of the uplift. The processes of subsidence and uplift are based on completely different mechanisms. Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding. INTRODUCTION After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—upward movement in the area above the past exploitation and in the immediate surroundings. Of course, most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method (Peng, 1986). This downward movement continues to occur at a smaller rate many decades after mining has been terminated when the water in the underground excavations is pumped to the surface. This is the case as long as a mine is in operation. However, after the closure and flooding of the underground excavations and the surrounding rock, this movement is reversed, and the surface is uplifted. A total uplift of about half a meter has been recorded to date. This phenomenon has been described in several different coal basins in Europe, for example, in Belgium (Devleeschouwer et al., 2008), France (Samsonov, d’Oreye, and Smets, 2013), Germany (Baglikow, 2011), the Netherlands (Caro Cuenca, Hooper, and Hanssen, 2013), and Poland (Preusse, Kateloe, and Sroka, 2013). To date, research has focused mainly on understanding the phenomenon (e.g., Herrero et al., 2012) and identifying general trends, whereby the link with the rise in water levels is an important issue (Caro Cuenca, Hooper, and Hanssen, 2013). The most accepted explanation is linked to the swelling of clay minerals in the argillaceous rocks in the coal strata (Herrero et al., 2012). Without doubt, the full explanation is complex, and swelling is probably not the only cause of the residual movement. Most coal strata rock is weakened upon contact with water. The increase in water pressure also results in a decrease in the effective stress. Both aspects facilitate the fracturing of rock, which normally would result in further subsidence. However, decreases in the effective stresses also result in the relaxation or expansion of the rock, which induces an upward movement (Fjar et al., 2008). All of these aspects, including the long-term residual subsidence due to compaction under dry conditions, result in a net upward movement. The phenomenon discussed here is clearly different from the upsidence, sometimes observed on other continents (e.g., in Australia, Galvin, 2016). When upsidence occurs, the rock near the surface bends and buckles upwards due to the overstressing of the floors of the valleys."

Jan 1, 2017

By Li Yang, Andre Cezar Zingano, Alberto Fronza

"Immediate roof control is very important to the security and stability of entries in coal mining. It is also the highest cost in the coal mining operation, and roof spalling is directly responsible for coal contamination. The immediate roof in the coal mines in the State of Santa Catarina varies in lithology and in the presence of structures, such as bedding planes, vertical fractures that cut lamination, sandstone, and siltstone boulders. The presence and crossing of these structures should influence the decision of the specification of the roof support. Furthermore, the variation of rock layer and quality of the roof must be immediately followed by the variation of support specification. This work aims to study the behavior of the immediate roof under different geological and structural conditions during the excavation of entries, including the changing of the geometry of the entry as a function of time. This includes the effect of vertical fractures that cross the bedding planes of the roof and the position of those fractures on the roof. The effect of time between excavation and installing support to stabilize the roof is also examined. This study uses empirical methodologies for support design and numerical methods to study the behavior of the roof when anchored to the different scenarios proposed. The results of this work show the importance of quality characterization of the roof in terms of the type of rock and its thickness and the presence of vertical fractures that cut the bedding planes of the roof immediately.INTRODUCTION The immediate roof in a coal mine can varies in terms of typology and structural features, like bedding plane spacing and vertical joints. The roof support must be specified based on the features of the roof layer and its classification. Unal (1983) and Mark, Molinda, and Dolinar (2001) suggest that the roof support design should be based on the rock mass rating (RMR) and coal mining roof rating (CMRR), which look at rock mass classifications. These methods are based on the beam-building approach, and the bedding planes are tied together using fully grouted bolt. The bolt can be pre-tensioned or not depending the time of the curing of the resin."

Jan 1, 2017

By Daniel W. H. Su

Thick, massive sandstone present in close proximity of the mining horizon can create difficult longwall caving issues, which may lead to severe face loading and subsequent face roof control problems. Under deep cover, such delayed caving and overhang not only impose additional loading on the gate road pillar system, but they also increase the potential for large seismic events. Such a combination of thick, massive sandstone geology and deep cover was present over a portion of a southwestern Virginia coal mine, which was confirmed via detailed in-mine roof scoping and mapping. Large seismic events were recorded over a district of 1,000-foot-wide longwall panels. This paper presents the ground control design changes implemented to reduce longwall-induced stresses in the sandstone, to reduce longwall abutment pressures in the gate road pillars, and to reduce the magnitude of mining-induced seismic events. A series of two-dimensional finite element models were constructed and analyzed to evaluate the longwall-induced stresses in the sandstone above the gate road pillars and the abutment pressures within the gate road pillars. Results from the analyses indicated that reducing the panel width from 1,000 to 700 feet reduced the longwall-induced stresses in the sandstone by a factor of 2.0. Specifically the probability of sandstone stability improved from 29% for the 1,000-foot-wide panel district to over 95% for the 700-foot-wide panel districts. Also, the subcritical 700-foot-wide panel, coupled with a change in pillar design, considerably reduced the longwall-induced abutment pressures in the gate road pillars, which significantly increased the gate road pillar stability factor. Surface subsidence measurements conducted over the 1,000-foot-wide panel district and two new 700-foot-wide panel districts were in very good agreement with those predicted by the finite element models. In addition, results from the models indicated that wider panels with a smaller district may produce the same probability of sandstone stability. One four-panel district and one five-panel district with the new ground control design changes have been mined successfully. The panel width was found to be the most influential factor in determining the longwall-induced stresses in the sandstone and in the gate road pillars. The thickness and massive nature of the sandstone, the proximity of the sandstone, and the strength of the sandstone were also found to be important factors. Seismic monitoring over the two mining districts that employed 700-foot-wide panels confirmed the reduction of one order of seismic magnitude when compared with those measured over the 1,000-foot-wide panel district.

Jan 1, 2014

By Charlie Li

A cut-and-fill mine stope, located at a depth of about 1000 m in a lead-and-zinc mine, was closed down because of large roof convergence and fractures appearing on the hanging wall. The instability problem was owing to the relatively low strength of the rock subjected to high in-situ stresses. Extra reinforcement was required to secure the stope so that the remaining ores in the stope could be mined. Assessment of the fracture mode in the country rock surrounding the stope was carried out and then the reinforcement de- sign was worked out. It was proposed that the unstable section of the stope would be reinforced by bolt-shotcrete ribs as well as selective long bolts. The philosophy of the design was to hold up the fractured country rock by bolts and shotcrete so that a load-bearing arch could be formed in the roof and in the hanging wall. Six shot- Crete ribs were set up in the unstable section of the stope. Displacement measurements showed that the roof convergence reduced from about 2 &day to the ordinary creeping level, about 0.25 &day, immediately after the reinforcement operation. Six month later, the hanging wall collapsed into the stope in a place just outside the reinforced section, which indirectly proved the effectiveness of the bolt-shotcrete ribs in reinforcing the fractured country rock. This case showed that an appropriate rock mechanics assessment would form a solid base for reinforcement/support design. It also provided an evidence for the philosophy of the reinforcement by bolt-shotcrete ribs - establish a load-bearing arch in the rock.

Jan 1, 2005

By Rossen A. Halatchev

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal mine.

Jan 1, 1992

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By Syd Peng, Gamal Rashed

"Bumps in coal mines have been recognized as a major hazard for many years. These sudden violent failures around mine openings have compromised safety, ventilation and access to mine workings. Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height (W/H) ratio of a coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. Unstable interface failures provide a sudden de-confinement to coal rib, thus triggering uns and compressive failure in the sidewalls. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. With a proper combination of interface friction and the width-to-height (W/H) ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure, which is brittle failure to non-violent failure, which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of width-to-height ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.10 and 0.25. The results are presented and discussed.INTRODUCTIONCoal mine bumps are sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillar, or the solid block of coal being thrown into an open entry. These bursts are accompanied by very loud noises (Peng, 2008). Several case histories in mining have long described coal pillars or coal faces failing violently with an accompanying ejection of debris and broken material into the working areas of the mines (Campoli et al., 1987; Osterwald, 1962; Peperakis, 1958; Garvey et al., 2013). Because of the catastrophic nature of these sudden failures, understanding the causes of coal mine bumps is essential to create a safe underground working environment. This phenomenon has motivated many ground control researchers to conduct extensive field investigations throughout the past century. Rashed and Peng (2014) compared the mechanical properties of two kinds of coal, one from bump and the other from non-bump-prone mines. They found that coal itself does not play any significant role in coal bumps and recommended that future research should focus more on the local variation of geological conditions such as the interface friction between pillar and roof and between pillar and floor."

Jan 1, 2015

By John C. Stankus

The 3 Right pre-developed longwall recovery entry at Signal Peak Energy?s Bull Mountain No. 1 mine was designed to prevent the abnormal roof conditions encountered in its firsttwo recovery entries. Unique geological conditions, such as the low overburden of approximately 200 feet and prevalence of roof joints in the sandstone overburden, contribute significantly to abnormal conditions during longwall recovery. The 3 Right recovery entry was 42 ft wide and developed in two stages, 21 ft wide in each stage. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, high-capacity primary bolts and cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. The roof bolting and backfilldesign were based on current practices in this mine and successful practices in other mines in the U.S. and Australia. Extensive instrumentation was installed in the recovery entry for continuous monitoring of load transfer as the face approached and cut into the recovery entries. The support design was completely successful with a smooth cut-through on January 29 and 30, 2014, significantly reducing the shield recovery time and meanwhile protecting the safety of miners. Based on actual observance and practices of the 3 Right recovery entry, recommendations on improvement and modificationsof roof support for 4 Right recovery room are presented.

Jan 1, 2014

By Denise Mueller, Axel Preusse

"In 2010, the fracking discussion in Germany caused a number of changes in German law, which came into force in 2016. Especially the production of gas had to be regulated. With the legislation amendment, the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbereichs-Bergverordnung) has been revised, too. The changes expand the compensation of mining damages, especially to the extraction with drilling from the surface and underground storage. Although the “Subsidence-Area Mining Regulation” has been revised, the area of main influence (subsidence of 10 cm) remains to determine a relevant boundary for mining damages. The determination and prediction of this boundary above caverns are presented in this paper. In addition, further elements of ground movements and their relevance to mine damages are analyzed. The usage of the area of main influence to fix a relevant boundary for mining damages does not correspond to the relevant elements of ground movements. A limit for differences in subsidence (tilt) or horizontal changes in length should be preferred to describe the relevance of mining damages on buildings. Furthermore, this paper outlines the the meaning of using the area of main influence to fix a relevant boundary for mining damages. INTRODUCTION The “Federal Mining Act” (in German: Bundesberggesetz, short: BBergG) forms the central legal standard to cover subsidence in Germany. The mining authority refers to the following regulations (Preuße et al., 2015): the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbergverordnung, short: EinwirkungsBergV; since 1982) the “Mine-Surveyor Mining Regulation” (in German: Markscheider-Bergverordnung; short: MarkschBergV) the “Deep-Drilling Regulation”"

Jan 1, 2017

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By Yongping Wu

Taking the longwall mining face area in a steeply dipping seam as the research object, the stability of an asymmetrical rock mass structure is analyzed using shell theory and masonry beam theory. The results show that an asymmetrical shell structure is formed at the top strata of the mining stope and its magnitude is mainly determined by the mechanical characteristic of the overburden strata of working face, mining space size and so on. Localized instability of the shell structure is the main factor that leads to the overall structural instability in the stope. The instability modes includes: the shell roof instability dominated by tensile failure, the shell shoulder instability initialized by compression-shear failure, and shell bases composite instability occurs in tensile and compression-shear modes. The shell structure stability dedicates rational strata control measures to choose, and the caving height of overburden strata is the key for shell structure instability.

Jan 1, 2013

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Jun Lu

This paper presents the evaluation, enhancement and comparison of two hydraulic fracturing techniques which were employed to mitigate the impact of a massive sandstone channel on two successive longwall faces. The hydraulic fracturing technique and Longwall Visual Analysis (LVA) software were initially employed to mitigate the impact of thick, massive sandstoneroof during mining of longwall Panel 21. Improved longwall face conditions and productivity were observed as Panel 21 mined through the sandstone channel. However, moderate sandstone fractures and falls at the face were still present in areas where hydraulic fracture influence was not present. Such adverse conditions caused two to three weeks of production delays due to large face cavities, jammed face conveyor and subsequent face gluing. Based on the mining experience in Panel 21, and site-specific roof geology in Panel 22, a modified and more effective hydraulic fracturing program was employed. Fewer well-placed holes were drilled, and larger volume of water was pumped into each hole in order to propagate the individual horizontal pancake fractures over a larger area, thereby enhancing caving and relieving face pressure caused by overhang of the massive sandstone. Longwall Visual Analysis (LVA) software was also employed at Panel 22 to predict the cavity risk index and guide the longwall face crew in double-pulling shields behind the shearer drum. This helped to reduce the tip-to-face distance at the critical spots along the longwall face, which helped mitigate the formation of the roof cavities and failure of massive sandstone onto the face conveyor. Underground observations, face advance rate and face rock delay analysis confirmed that longwall face conditions and advance rate in Panel 22were significantly improved compared to those of Panel 21. Consequently, safety and productivity were improved.

Jan 1, 2014

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By Christopher Mark

Dr. Christopher Mark serves as Team Leader of the Rock Mechanics Section in the Rock Safety Engineering Branch of the NIOSH - Pittsburgh Research Laboratory. In this position he leads a multi-disciplinary team and conducts individual research directed towards fundamental ground control safety issues affecting miners. Dr. Mark is recognized as one of the country?s leading authorities on coal mine ground control. Through his research, he has made numerous important contributions to mine safety that have been widely adopted into mining practice. He is a highly original researcher, and has often developed new and innovative methods to tackle extremely complex problems in his field. In recent years Dr. Mark has also achieved wide international recognition. Five research projects in Canada, Australia, and South Africa have been based largely on his work.

Jan 1, 2007

By G. Skybey

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By Murali Gadde

Numerical simulation of cutter roof failure is a daunting coal mine excavation design issue. The complex progressive failure mechanisms associated with cutter failures are extremely difficult to replicate in computer models. However, this paper shows that with a proper selection of constitute behavior and implementation of cutting sequence, it is possible to realistically reproduce cutter failure using continuum models. Strain-softening material behavior and a systematic step-by-step model solving for a four-entry-and- three-crosscut model produced results that are similar to cutter patterns noticed in field. These results show that traditional modeling with geometries created in one model-step has limited applicability and may even provide misleading conclusions under some circumstances. Most importantly, the proposed modeling methodology provided some insights into the reasons for the inconsistent spatial distribution of cutters often noticed in coal mines. The modeling also revealed the usefulness of cutter mapping to determine the directions of in situ horizontal stresses.

Jan 1, 2005

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001