Search Documents

By Gregory Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-¬injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

Jan 1, 2004

By S. MacGregor

The role of horizontal stress, its orientation and magnitude, in defining the behaviour of strata in underground coal mines has been well established. Poor panel layouts have led to gate end stress concentrations, roof falls and lost production. The ability to define the horizontal stress regime over a mine site has historically been limited to point measurements, in part due to technology and cost. Recent advances in the application of geophysical tools, notably the acoustic scanner (borehole televiewer) have resulted in a new technique to conduct stress measurements. By quantifying the nature of borehole breakout and the mechanical properties of rocks in which they occur, this technique provides the ability to: obtain a vastly greater number of measurements, both at different depths and spatial distribution, than other techniques such as overcoring or hydraulic fracturing readily obtain depth versus stress relationships define geotechnical domains on the basis of stress direction and in-situ stress magnitude for mine planning purposes This paper presents an overview of the technique and presents case histories in its application at a mine site in the Sydney Basin, Australia.

Jan 1, 2002

By Tetsuro Esaki

This paper describes the present condition of mining-induced damages in Japan and the characteristics of them. The change of mining operation and environmental condition has caused various significant impacts on the ground environment: subsidence, cave-in, springing out of ground water etc. The characteristics and the influences of these phenomena are discussed by investigation of the actual conditions and by fundamental studies. Some counter measures are also introduced.

Jan 1, 1989

By Xun Luo

In this paper we report on the use of microseismic monitoring techniques to investigate the fracturing process associated with longwall mining. The study was carried out at three mines in Australia and concentrated on some major concerns of the mines, such as failure patterns and growth rate associated with mining progress, their implications to water ingress and gas emissions, caving processes in the goaf and precursors of roof falls. The results have shown that a zone of shear fracturing has occurred further ahead of the longwall face than predicted using conventional longwall geomechanics theory. Failure patterns in the roof and floor vary from mine to mine and this appears to be dominated by geological structures. The reaction of faults, the formation of fractures which allow gas emissions and precursors roof falls have also observed. Results from this work have opened up new understanding of longwall caving processes and proved that microseismic monitoring is a very useful technique for studies of longwall geomechanics and hazard controls.

Jan 1, 1998

By R. J. Morrell

The Bureau of Mines developed a ground support system for use with an underground coal auger. The system consists of inflatable airbags that are inserted in the holes as they are drilled, and then gradually deflated to provide controlled roof caving. This paper presents results of laboratory and field tests of the system that show it to be technically feasible.

Jan 1, 1988

By Daniel W. H. Su

Underground roof geology reconnaissance is being conducted by CONSOL Inc. to enhance mine productivity. Often, roof instability within mine entries is the consequence of highly variable geology that cannot always be detected from information provided by widely-spaced surface core holes. Utilizing a combination of roof drilling data, geophysical logs, and borehole camera and fiberscope observations, roof geology mapping is conducted within longwall development entries in areas of specific concern prior to commencement of longwall mining, Depending on the uniformity of the site-specific roof geology, data point spacing along the longwall development generally ranges from one to five crosscuts. Surface core hole data are correlated with the roof geology mapped underground to validate the underground observations. Detailed roof geology maps can then be produced to enable ground control engineers and mine management to select cost-effective ground control techniques. However, this procedure is not necessary or useful in all situations and it is employed only when there is strong geologic evidence to justify a closer inspection.

Jan 1, 1999

By B. Singh

The use of wire ropes has already been tried in a few countries for roof support In mines. But the use of scrap wire ropes, as a method of support on extensive scale has not been reported from anywhere except India. Extensive trials using freshly discarded wire ropes for roof support were undertaken both in the laboratory and field. In laboratory, model beams supported with different reinforcing techniques were tested to evaluate their comparative load bearing capacity vis-a-vis reinforcing factor. Among all the tests, the model supported with wire rope system at 60° angle in combination with two supplementary vertical bolts offered the best result 1.e. about 95% reinforcement. It also accepted post fracture loading of the beam. In statical analysis too, the best result could be obtained with the rope installed across the gallery at 60° angle. All these findings are in conformity with the field observations obtained during roof stitching practices in coal mines. Of late, roof stitching, an effective and economical method of roof support developed at CMRS, India in 1972, found wide application in over 200 coal mines. In this method, a freshly discarded wire rope is grouted across a gallery in two inclined drill holes supplemented with two middle vertical roof bolts at every 1.0 to 1.2 m interval along the gallery. It is tensioned against the roof using wooden sleepers and thus, the whole system functions like a roof truss.

Jan 1, 1990

By John A. Rusnak

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load France and point load testing of coal measure rocks in six states. More than 10.000 individual test results. From 908 distinct rock units, sere used in the study. Rock lithologies were classified into general categories and conversion factors were determined For each category. This allows for intact rock strength data to he made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).

Jan 1, 2000

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By Rene Rodriguez

The initial results of our investigations on the applicability of geophysical exploration methods to map coal seam inclusions were summarized in a paper submitted at the Thirteenth Conference on Ground Control in Mining in 1994. These investigations were continued under a variety of conditions at a number of underground coal mining operations. The results have been encouraging and have fostered a much more detailed understanding of the geophysical principles at work in underground mine mapping. This report summarizes a particularly interesting application, that is, the use of Underground In-Seam Seismic exploration methods to identify and to approximately delineate coal seam inclusions within longwall panels. The methodology relies on the excitation of seismic sources in the coal seam along one side of the panel and the recording of seismic waves by geophones secured to the coal rib on the opposite side. Head-Body waves (compressional and shear), direct and channel waves are generated in the process. While the head waves are critically refracted waves traveling at the coal floor and roof, direct and channel waves are transmitted through the coal body and are dispersive in character. Tomographic techniques applied to the velocity inversion of first arrivals permits a fast mapping of coal seam inclusions in the panel. The process incorporates path velocity and geostatistical intersect analysis. Full wave analysis of the dispersive channel waves, provides an independent and confirmatory information of the coal geometry, including the inclusions within. The inversion technique in this case is the modal analysis of the wave trains. The application of this method to three different problems was confirmed by subsequent mining of the predicted anomalies, proving the accuracy of the technique within limits of experimental error.

Jan 1, 1995

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By T. P. Mucho

Mine roof failure due to excessive horizontal stress has been recognized as a major cause of hazardous roof conditions in some mines. Stress measurements gathered by the U.S. Bureau of Mines (USBM) at 24 different eastern mines show horizontal stress to be typically 2 to 3 times as great as vertical stress. The focus of current Bureau work is to develop detailed design parameters to assess and control the effects of horizontal stress. To facilitate the recognition of horizontal stress effects and to easily determine principal stress direction without resorting to cumbersome, expensive, and time consuming field measurements, the Bureau has developed a stress mapping methodology. Stress recognition and direction determination are required to successfully employ a number of control strategies such as mine layout, mining sequences, and support optimization to control the effects of horizontal stress, thereby increasing the safety of U.S. coal mines. This approach has been used in other major coal producing countries, most notably Australia and the UK, and has greatly enhanced the safety of their mines (1). This paper discusses horizontal stress, directional based control techniques, and provides guidelines for the use of the stress mapping technique. A case study of a mine where the technique has been used is also presented.

Jan 1, 1994

By Keith Heasley

An eastern longwall mine was required to mine through a set of three entries located midway down the length of a panel. Of course, the mine desired to design a successful support system for the mine-through area at the least cost. To further complicate the design process, the mine-through entries were located directly under the end of a previously mined, overlying longwall panel and the entries were close enough to be subject to stress interactions from the overlying seam. In order to accurately evaluate the multiple-seam stresses and modify the mine-through support system appropriately, the boundary element program LaModel was used to model the stress and displacements in the two mines. Using the results of the model's stress analysis, the support density was systematically varied throughout the mine- through entries for optimum sup@ efficiency and economics. During the actual mining of the cross panel entries, the longwall experienced few, if any, additional delays, and overall, the support and mine through of the cross-panel en- tries at Harris #1 was very successful, saving the mine confineable time and money.

Jan 1, 2003

By D. Newman

An underground limestone quarry, developed in the 1940's, transitioned from a surface quarry to an underground room-and-pillar operation. The quarry expanded to a second underground level when the reserves on the first level reached the property boundaries. The historical basis for the sill pillar thickness between the first and second level, pillar dimensions, and mining height was lost during the course of several changes in ownership. When reserves on the second level reached a five-year life, and plans were initiated for a third level, quarry management embarked upon a thorough evaluation of i. current ground control practices for the support of the immediate roof, ii. roof support in the declines between the surface, Level 1, and Level II, iii. pillar centers and pillar safety factors, iv. pillar alignment between levels, v. mining height within a level, and vi. the locations of declines to access future reserves on level three. The evaluation began with detailed mapping of the location and orientation of calcite veins, joints, fractures, and ground conditions in the immediate roof of Level II. The orientation and location of calcite veins, joints, and fractures on Level II were compared with similar mapping on Level 1, completed in the 1970's to establish whether these features were continuous and would be expected to affect conditions on Level III. Rock strength, physical properties, and fracture spacing were obtained from two (2) diamond core holes drilled from Level I to Level II and two (2) holes drilled from Level II to define the vertical extent of future reserves on Level III. The effort to characterize geological conditions was expanded to a rock mechanics investigation of the: i. performance of the current roof support, ii. optimization of roof and rib scaling, iii. calculation of safety factors for 416 pillars on Level II, iv. evaluation of future pillar centers and mining height within a level based upon pillar strength and pillar geometry, v. development of beam safety factors for the immediate roof on Level II, vi. identification of the most suitable strata for the roof in the future level three, and vii. use of LAMODEL to develop a large numerical model of overburden, inter-level, and total stress on the pillars in levels one and Level II with a stress "footprint" on the proposed level three. The characterization of engineering parameters and geological conditions resulted in changes to the: ? active operations in Level II regarding scaling ? equipment and scaling practices, ? pillar centers, ? mining height, ? raising the immediate roof horizon to avoid ? laminated strata in the current roof, and ? a change in rock bolts from a friction based system ? to active tensioned rebar. The planning and design of level three is ongoing and relies heavily upon the geological and engineering investigations conducted during the past year and one-half.

Jan 1, 2001

By Gregory Molinda

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3 way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

Jan 1, 1998

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By Laxminarayan Holla

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

By Duk-Won Park

The excavation of a longwall panel causes a continuous stress redistribution in the surrounding strata for every face advancement. The understanding of the behavior of rock to high level of stresses is instrumental to the structural design of underground mines. In order to achieve a realistic analysis of the behavior of strata, the three-dimensional finite element method is frequently used. Also the model developed for the analysis has to be designed large enough to represent the influenced strata in the study area and a sufficient number of elements has to be used to provide detailed information on the stresses and displacements. Due to the size of the model and its numerical solution the CRAY X-MP/24 supercomputer has been used for this study. The mine site selected for the analysis is a coal mine located in the Black Warrior Basin in Alabama. The mine has two longwall sections at a depth of 2,000 feet with various dimensions of chain pillars, including yield pillars. Various research programs at this mine have been carried out by Park et. al. ( 1984 ). Therefore data were already available on the geology, and physical properties of rock and coal. In addition a rock testing program has been carried out to obtain rock mass classification parameters. The progressive failure technique has been utilized to simulate stress redistributions. The failure criterion after Hoek and Brown ( 1980 ) which is based on rock mass behavior was used for the iterative technique. Simulated stress redistributions are therefore very realistic. In order to automate the process involved in the application of progressive failure technique, a computer program has been developed. The combination of a large scale three-dimensional finite element model and the automation of progressive failure simulation provided a tool that can generate a large amount of information related to the behavior of rock and coal as a response to a longwall mining operation.

Jan 1, 1989

By Robert Trueman

This paper details the results of an assessment aimed at understanding the shield loading mechanisms associated with strata-related issues on a longwall face. Shield load cycle analysis theories developed by the authors were used to quantify the interaction between the shields and strata. Shield pressure data was back-analyzed using a version of the Longwall Visual Analysis (LVA) software that has been extended to enable efficient load cycle analysis to be undertaken. The software outputs enabled the shield strata interactions to be characterized. The results of the analyses indicated that the major cause of the roof falls was high-level periodic weighting, resulting in periodic shield overload. Exploration borehole data was analysed to identify and characterize the overburden unit that was the likely cause of the shield overloading.

Jan 1, 2011

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998