Search Documents

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By Paul L. Tyrna

The Fola Coal Co., LLC No 2 surface mine, located in Nicholas and Clay Counties, WV, exploits up to nine coal seams by contour, highwall, and mountain top removal mining methods. After encountering faults, areas of highly fractured coal, and subsidence failures. the mine requested a lineament analysis from the Mine Safety & Health Administration's (Pittsburgh Safety and Health Technology Center) Roof Control Division. The 31 km2 study area was viewed on a LANDSAT-5 band 4 (near infrared, 0.76-0.90 µm wavelength) satellite image with ERDAS Imagine 8.4 software. The software allows image examination under artificial sun azimuths and elevations, resulting in variable tonal characteristics. The study area image was viewed in 45° azimuthal increments from 000° to 315° at artificial sun angles of 10°, 30°, 50°, and 70°, yielding 32 separate images. The interpretation process developed by MSHA Roof Control personnel identified 16 northeast-striking and one northwest-striking lineament that intersected mine property. Faults and areas of roof instability corresponded well with lineaments identified in the study. Successful lineament identification prompted mine management to incorporate lineament analysis as a mine-planning tool for adjacent property, thereby identifying in advance areas that could adversely affect safety and production.

Jan 1, 2001

By Anthony T. Iannacchione

The Solar No. 7 and Solar No. 10 mines were designed to prevent mine waters from directly discharging to the surface. In January of 2004, a discharge occurred as the Solar No. 7 mine was in its final stage of flooding through a barrier averaging 456-ft in width over a 1,600-ft length (No. 1). Another barrier (No. 2) was designed to protect four municipal water wells operating 1,800- ft away and producing from within or slightly below the Upper Kittanning coalbed from the adjacent Solar No. 7 and No. 10 mine pools. These two barriers were selected for this study because of varied mine layouts, mining methods, and geology factors affecting their performance. Analysis was aided by the collection and georeferencing of 6-month mining maps from the Pennsylvania Department of Environmental Protection (PA DEP). A structure contour map of the Upper Kittanning coalbed was constructed from mine map elevation points. These data and 2-ft surface contour maps were used to measure the precise location of the coal outcrop. The actual discharge point was as little as 425-ft away from a thinpillar section and 475-ft away from a pillar recovery section. The discharge point was found to be located slightly above the coal, indicating that the drainage path was at least partially through the strata directly above the Upper Kittanning coalbed. Hydraulic conductivities and potential discharge pathways are analyzed and discussed. The possible factors influencing the performance of the down-dip barriers at Solar No. 7 and Solar No. 10 are: a) the width of the barrier, b) the applied hydraulic gradient, c) the type of mining adjacent to the barrier, d) the overburden, e) the pattern and characteristics of fractures, and f) the quality of waters contained within the mine pools. This study, part of a larger effort funded by the Appalachian Research Initiative for Environmental Sciences (ARIES), is tasked to determine the key factors responsible for the successful design of down-dip coal barriers.

Jan 1, 2013

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By Ding Xu Chu

There are many methods developed for measuring the crustal stress in China. Among them only two methods have been adopted in practice, i.e., overcoring method (for which the sensors include: Piezo-magnetic stress gauge, steel-ring strain cell, 3-dimensional hollow-inclusion stress ,gauge, and Leeman's-like stress gauge) and hydraulic fracturing method. For the former method, one of those sensors is installed in a borehole, 36 mm in diameter, then prestressed, and finally overcored with a drill bit of 130 mm in diameter. After that the deformation of the borehole wall is measured, from which the in-situ stresses are determined. In order to avoid the errors resulting from the difference in elastic modulus for various kinds of rocks as well as from the installment of the cells, we have developed a technique to calibrate the sensor on-spot using a confining pressure calibrator and produced a very good result. For the later method, the measurements are achieved by isolating a certain section of a borehole and then injecting water to pressurize it till a tensile break is induced. It is identical to the typical technology used internationally. For many years, through field observations and a large number of laboratory experiments, we believe that the most efficient way of stress measurement for engineering purposes is the overcoring method using Piezo-magnetic stress gauge. It is characterized by stable and reliable measurement values, high accuracy and high adaptability. Taking the measurements in the intact rock mass as an example, the measured stress magnitudes are within accuracies of 8% and the errors in orientation are about 5 degrees. It can even be used perfectly in deep water. Up to now, we have performed in-situ stress measurements in more than 70 sites and obtain more than one thousand sets of data. The deepest depth used in the overcoring method is 80 m in vertical borehole and 780 m in tunnels.

Jan 1, 1987

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By Bo-Hyun Kim, Steve Berry, Mark K. Larson

"When coal pillar bursts occur, they involve the sudden expulsion of coal and rock into the mine opening. These events occur when relatively high stresses in a coal pillar, which serve as support in underground workings, exceed the critical capability of the pillar. This causes the pillar to rupture without warning. A cleating is a type of naturally occurring joint system unique to coal seams. However, cleatings are pervasive throughout the coal seam and are much more tightly spaced than joints occurring in other rock types. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated 84 coal samples obtained from a Utah coal mine by conducting both unconfined and triaxial compressive tests in order to examine the response to stress as a function of both confinement and orientation between cleat and loading direction. The results of the study show that the confining pressure dictated not only the peak compressive strength but also the brittleness as a function of the major-to-minor principal stress ratio. The spalling limit of the coal estimated by the s-shaped brittle failure criterion appears to be very dependent on the angle between the cleat and the loading direction, particularly at lower confinement.INTRODUCTIONCoal pillar bursts, or bumps, remain a most critical safety concern in underground coal mining, despite significant advancements in engineering controls. As shown in Figure 1, between 1983 and 2014, there were nearly 400 cases of reportable dynamic failure accidents in coal and nonmetal mines, resulting in 20 fatalities, 155 lost-time accidents, and an estimated 48,000 lost man hours (MSHA, 2015). These types of events have been documented for well over 100 years within the American underground coal mining industry. During this time, mining practices and support technologies have evolved considerably, resulting in an overall decrease in the rate of dynamic failure-related injuries and fatalities. Although techniques and practices of mining are highly advanced, coal pillar bursts, or bumps, continue to occur (Mark and Gauna, 2015). If coal is expected to fail in a brittle manner, behavior changes associated with relatively low tensile strength, such as the transition from tensile to shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile failure in heterogeneous rocks (Diederichs, 2007). The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it is expected that the transition from tensile to shear mode in the failure mechanism occurs as the confinement level changes and conditions for tensile failure are prevented or strongly diminished. In addition, many uncertainties remain because of the highly anisotropic characteristics of coal seams associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous effort is required to better understand the catastrophic failure mechanisms in coal mines."

Jan 1, 2018

By Xianxin Shi

In surface electrical exploration the high resolution earth resistivity method (HRRM) is a very effective method for detecting abandoned drift mines workings. When the abandoned mines are more than 500 ft (150 m) deep, its detection capability reduces greatly and requires more effort to implement. In Yan Quan coal mine, Shanxi province, we tried to adapt this method for underground application. Two survey lines were designed with the spacing of current and potential poles 20 m and 10 m, respectively and measuring points at 2m. The measurement radius of I line and I1 line were 140 m and 60 m, respectively, and the infinitely far pole was 1200~2000 m from the survey line. (Note the I and II lines are located on the north and south ribs of main tunnel, respectively). The survey results showed that abandoned workings were located at 25-70m, Survey Line I and at 80-1 10m, Survey line 11. Based on this finding, the longwall panel gateroads and set up entry were properly located thereby providing safe mining of the No. 15 Coal seam. Key Words: Abandoned coal mine, High resolution earth resistivity, Underground electrical exploration

Jan 1, 2005

By Chase K. Barnard, Rahul Thareja, Sean Warren, Rajagopala Kallu

"Inflatable rock bolts are commonly utilized for ground support in Nevada underground mines, however, there is limited information regarding what factors influence the bond strength of these bolts. Bond strength is an important parameter in friction bolt support design, and this information is usually not available from manufacturers as a standard. Previous research has investigated the bond strength of friction bolts; however, these studies focused primarily on split set bolts and ground conditions more favorable compared to those commonly encountered in Nevada underground mines. Without site-specific bolt pull-out tests, ground control engineers are required to make assumptions regarding the in-situ bond strength of rock bolts. This is especially a concern for projects in the feasibility and initial development stages before site-specific experience is acquired.The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the Rock Mass Rating (RMR) system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively correlated with RMR, however the correlation is not strong. Cumulative percent graphs indicate that 97% of pull-out tests result in a minimum bond strength of 1 ton/ft and ½ ton/ft in RMR =45 and <45, respectively.Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed."

Jan 1, 2015

By Bo-Hyun Kim, Mark K. Larson

"While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex with different branches that reactivate at different times. Furthermore, these branches are zones of non-zero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D™ software program. The initial and boundary conditions are simplified and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.INTRODUCTIONThis paper is part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bump-prone potential in highly stressed ground conditions. More specifically, this paper reports an exploratory effort with an unconventional approach using a numerical tool to try to better understand a possible scenario where bump risk might be increased—that is, a scenario involving a strike-slip fault. The objective is to assess whether a numerical tool might be useful or practical in forecasting bump potential associated with a strike-slip fault for a typical, structural geologic setting."

Jan 1, 2018

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By Esterhuizen S. Gabriel, Su W. H. Daniel, Tulu B. Ihsan, Klemetti M. Ted, Mohammed M. Khaled, Gearhart F. Dave

"A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face. In this approach, a systematic procedure is used to estimate the model inputs. Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements. Coal is modeled with a newly developed coal mass model. The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments. The model results have been verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States. INTRODUCTION In 2015, there were 40 longwall mines operating in the United States, each producing an average of 4.5 million tons of coal per year, and they supplied 60% of the U.S. underground coal production. This represents a substantial increase from 50% three years earlier (Sears, Tulu, and Esterhuizen, 2017). During this period, reportable roof fall rates in U.S. longwall mines also increased. Large roof falls that can block the gateroads are not only a ground-fall hazard, they can disrupt the ventilation system, block the escapeways, and increase the potential for elevated methane levels in the gob. To address these hazards, the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) is conducting research to improve the design of ground control systems in longwall gateroads. Gateroad stability is primarily determined by the longwall pillar design. Generally, the required dimensions of the pillars around a longwall panel are determined first, which then dictates the location of the gate entries relative to the mined panel. The Analysis of Longwall Pillar Stability (ALPS) method is the most accepted gateroad pillar design procedure in the United States (Mark, 1992). The ALPS method accounts for local roof geology in the gateroad stability assessment by including the Coal Mine Roof Rating as an input parameter (Mark, 1992). The key assumption in the ALPS method is that unstable pillars result in unstable gate entries. However, experience provides examples of mines where pillar stability and gateroad stability are only loosely correlated (Su, Draskovich, and Thomas, 2003)."

Jan 1, 2017

By Hongwei Zhang, Sen Yang, Shimin Liu

"This laboratory study investigates the damage evolution of sandstone specimens under two types of cyclic loading conditions through monitoring and analyzing the variations of elastic moduli and ultrasonic velocities. We adopted the rigidity degradation method for evaluating the damage accumulation through the rock dynamic ultrasonic velocity measurements. Compared to the ultrasonic test, the method of rigidity degradation shows deficiencies in the detection of damage development. The cyclic loading within the elastic limit led to a stiffening trend for the loading process but a softening trend for unloading process. The method of rigidity degradation was unable to describe the damage accumulation in this situation, while P-wave velocity clearly reflected the damage development. Moreover, a simplified model is established for interpreting the behaviors of the modulus variations and ultrasonic velocity. The cyclic loading within elastic limit enhances the anisotropy of rock, which causes a denser packing pattern in the direction of axial stress. The persistent damage accumulation under the cycling with an increasing upper limit is the consequence of the tensile failure in the microstructure of sandstone. INTRODUCTION The damage accumulation due to dynamic (cyclic) loading is highly detrimental in many engineering structures, such as mine openings, petroleum and natural gas boreholes, tunnels, rock foundations, and underground chambers. The sources of cyclic or repetitive loadings can be roughly divided into two types: (1) periodic operation, including drilling, blasting, and mining; (2) random vibration, including earthquakes and traffic loads. The repetitive loading-unloading process opens and closes the micro-pores and micro-cracks within the rock, further inducing the growth of cracks. As expected, the accumulating damage becomes a potential factor to trigger the rapid and violent failures of large-scale engineering rock structure."

Jan 1, 2017

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017