Search Documents

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By Arka Jyoti Das, Prabhat Kumar Mandal

"Coal mining in India has a strategic importance for the energy security of the country. Presently, the majority of coal production is coming from open-cast mining. Due to the fast depletion of reserves amenable to open-cast mining, future coal production will depend primarily on underground production. In conventional bard-and-pillar/room and pillar mining as it is practiced in India, the percentage of extraction is very low. In fact, within most Indian coalfields, a large number of coal seams extract only 15- 20% of coal, but no pillar extraction is done due to the presence of surface or sub-surface structures leading to huge amount of coal being locked-up in underground. Spontaneous heating and fire, the accumulation of poisonous gases, severe stability issues, unsafe workings and environmental hazards are all major problems associated with these developed coal pillars, so there is a pressing need for technology in the mining industry to extract this huge amount of coal locked up under different constraints. In this study, we propose that the locked-up coal be extracted by replacing the developed coal pillars with artificial pillars. The paper briefly discusses the extraction methodology designed for this and its evaluation through numerical modeling for applied suitability underground.INTRODUCTIONDriven by rising populations and urbanization, an expanding economy and also a quest for improved quality of life, energy usage in India is expected to increase manifold in the coming years. As for India's energy scenario and its projected future plans, there is no doubt that coal will remain a prime source of energy, even over the next few decades.The majority of coal production in India comes from open-cast mining because of large-scale mechanization, but the coal reserves amenable to open-cast mining are gradually depleting - which may impose adverse impacts on the energy sector if underground production does not increase. Underground coal extraction, meanwhile, is going to become more complicated in near future due to the fast exhaustion of easily mineable coal reserves."

Jan 1, 2016

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By Long Fan, Shimin Liu, Guijie Sang

"Weak shale roof falls have long been the main cause for fatalities in underground coal mines. Moisture-induced swelling is one of the root causes for the degradation of roof shales. In this study, slake durability tests are conducted on shale samples collected from Illinois basin coal mines, and different levels of durability are analyzed according to Gamble slake durability classification. There are two main mechanisms influencing the shape of retained fragments after two cycles of wetting and drying: mechanical abrasion and swelling pressure. A prototype optically based shale swelling apparatus is designed and manufactured for the shale free-swelling measurement. The experimental results suggest that swelling pressure tends to deteriorate shale laminations. Moisture-induced swelling of the No. 6 roof shale from Bear Run Mine was measured under 100% relative humidity condition. The measured swelling strain normal to beddings is ~5 to 7 times greater than the swelling strain parallel to beddings. This suggests that interlayer expansion plays a key role in moisture-induced swelling. Cracks induced by swelling pressure tend to occur along the bedding plane and lead to shale deterioration. INTRODUCTION Background Ground falls have long been the cause for nearly 50% of all fatalities in underground coal mines and continue to be one of the greatest safety hazards in underground spaces. Among the various ground fall hazards, roof failure takes up 23% of total fatalities in underground coal mines, of which 13% are due to skin failure and 10% are due to massive roof falls (Mark, Pappas, and Barczak, 2011). Roof failures associated with weak shales are summarized in previous studies (Molinda and Mark, 2010; Aughenbaugh and Bruzewski, 1973; Bajpayee, Pappas, and Ellenberger, 2014; Murphy, 2016). For mine roof instability and failure, two aspects can explain the failure mechanism of weak roofs. One is the elevated stress concentration in lateral direction due to the mining-induced excavation and its stress redistribution around the mine opening (Song and Stankus, 1997; Fan and Liu, 2017; Hill, 1986). The other mechanism is the passive stress-relief due to the strength weakening induced by the ambient moisture and temperature fluctuations during a period of time. Shale is moisture sensitive and presents a lower durability if it is exposed to a highly humid environment for a long time, thus leading to roof deterioration and instability in underground coal mines (Aughenbaugh and Bruzewski, 1976; Stateham and Radcliffe, 1978; Chugh and Missavage, 1981; Klemetti, Oyler, and Molinda, 2009). It is well known that shale is a clay-bearing sedimentary rock and that clay minerals are water sensitive. The moisture uptake for shale will induce the micro-deformation of a shale matrix, thus the structure and strength of shale is a function of time and intensity of moisture exposure. All mine engineers notice moisture-induced shale deterioration; however, the underlying mechanism(s) are still not fully understood due to the complexity of geophysical-chemical water-shale interactions (Huang, Aughenbaugh, and Rockaway, 1986; Hensen and Smit, 2002; Diaz-Perez, Cortés-Monroy, and Roegiers, 2007). The coal mining industry is still in the process of finding a technically sound, cost-effective technology to prevent this unexpected and unpredictable shale roof failure. Therefore, understanding how the moisture-sensitive shale responses to various ambient moisture and what role exposure duration plays in shale roof failure is key to prevent unexpected roof incidents, which will lay the foundation for the long-term roof support design and ground control management."

Jan 1, 2017

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By Liang Dong, Jinxuan Liu, Biao Qiu, Jing Chai

"The Cenozoic unconsolidated strata in the east area of China are composed of clay, sandy clay, fine sand, hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged in various degrees since 1987. The main reason for this disaster is the vertical additional stress on shaft caused by the subsidence of the thick unconsolidated strata. In order to monitor the subsidence deformation of the unconsolidated strata, a sensing network system with multiplexed Fiber Bragg Grating (FBG) for monitoring settlement deformation of the unconsolidated strata in deep borehole is proposed. The field monitoring results show that, soil layers settle or expand with decrease or increase in ground water levels. The thick hardpan generates the main compressive deformation. This FBG strain monitoring method can take place of traditional ground water measuring method. This system is stable and reliable, and the monitoring results can show the subsidence deformation of different layers, which has significance for the predictive maintenance of the shafts.INTRODUCTIONSince 1980s, a specific geologic hazard has occurred frequently on the coal mine shafts in eastern China: non-mining-induced shaft deformation, involving up to 100 shafts located in Jiangsu, Shandong, Anhui and Herran province, distributed in Xuzhou, Datun, Huainan, Huaibei, Yanzhou and Yongxia coal fields. This kind of geologic hazard can lead to shaft wall deformation, water infiltration, cage stuck, water-sand burst or shutting down of coal mines, which seriously risks the coal mines. Zhangshuanglou coal mine, Haizi coal mine and Linhuan coal mine shut down for 2-8 months due to this hazard (Chen, 1997; Cui, 1998). The main reason for this geologic hazard is the subsidence of the super thick unconsolidated strata (Liu et al., 2007; Xu et al., 2006).An innovative structure health ·monitoring and damage estimation method has been developed in recent years, i.e., optical fiber smart material and structure (Nobuo, 2002; Wang et al., 2000). A Fiber Bragg grating (FBG) sensor is a device that can transfer the change of the measured strain or temperature to the change of Bragg wavelength. One of the most important applications of FBG sensors is to monitor the internal stress and strain distribution of material and structure (Philipp et al., 2000; Ansari et al., 1998). Compared to traditional electrical sensors, FBG sensors have many advantages; they are adaptable to harsh environments, abrasion resistant, immune to electrical magnetism (EM) interference, safe and reliable. They also offer integrated sensing and transmission on a single fiber, have simple structure and are convenient to use, which satisfies the requirements of long distance, distributional and long term use in monitoring mining and geotechnical engineering structure. Due to such advantages, the FBG sensor has already been applied in petroleum engineering (Kersey, 2000), rock mechanics testing (Cornelia et al., 2003; Yang et al., 2007; Wei et al., 2008), physical simulation experiments (Chai et al., 2007; Chai et al., 2006; Zhu et al., 2008; Li et al., 2008; Chang et al., 2008), strain sensor (Li et al., 2007; Chai et al., 2008) and construction structure damage diagnosis (Dong et al., 2004; Kerrouche et al., 2008; Whitten et al., 2001)."

Jan 1, 2010

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Michael J. Castner

"INTRODUCTIONMultiple-seam mining is an ever growing concern for engineers and mine management in every portion of the mining industry and is especially true for coal mining operations. The goal of this report is to identify the location and severity of multiple-seam interactions, provide AMSS calculations performed on the worst of these locations, and follow up with a visual examination of the underground physical effects on the roof and ribs in the locations identified for analysis. Multiple-seam mining is increasingly being studied because:1. Multiple-seam mining can create a multitude of problems such as roof falls, pillar crushing, pillar failing, rib spalling, floor heave, and inundation of water, gas, or oxygen-deficient air that can disrupt mining operations and threaten the safety of the miners.2. Multiple-seam mining is becoming more prevalent due to the depletion of virgin coal reserves.Currently, coal mining in the United States has progressed to the point that a growing number of mining companies are operating in coal seams located above, below, and/or adjacent to previously mined out coal seams. As a result, the state and federal governments are enacting higher safety standards on mining operations. For example, in years past, pillars may have been properly designed to handle single seam interactions for a particular mine or mines; however, today, where mining is now being considered above or below a previously mined area, these loading conditions may not be adequate to handle the removal of additional seams above or below the previously mined reserve. Studies from 1981 estimated that two-thirds of the mineable coal reserves in the United States would be impacted by multiple-seam implications. Today, over three decades later, it is obvious that most of the remaining mineable coal reserve will be influenced by previously extracted seams. Thus, thefocus on multiple-seam mining interactions on current and future mining operations. In 2012, underground mining in the United States produced 342,287 thousand short tons of coal. Northern Appalachia accounted for over 30% (103,301 thousand short tons) of this total (U.S. Energy Information Administration, 2013). Rosebud Mining Company and Western Allegheny Energy (RMC and WAE) have a combined total of 23 actively producing underground mining operations and at least four new mines under or ready for development. All of these mines are located in coal seams (Upper and Lower Freeport; Upper, Middle, and Lower Kittanning) of northern Appalachia (Pennsylvania and Ohio). Currently, more than half of the RMC and WAE mines are dealing with multiple-seam interactions. Seven mines are undermining previously mined out coal seams, and five mines are overmining previously mined out coal seams. Also, between these companies, five mines have inner-seam sloping possibilities (2 completed, 3 planned), most of which will result in mining over or under previously mined areas."

Jan 1, 2015

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The design of underground coal mines requires a clear understanding of the overburden response, the loading of pillars, the loading of the gob, the pillar failure process, and the ultimate load carried by partly or fully yielding pillars. Very few highquality stress measurements of yielding pillars and gob loading have been made in full extraction mining. Well-calibrated numerical models can assist in providing a better understanding of the load and failure processes, provided the coal, the overburden, and the gob are all modeled with sufficient realism. A program of numerical model calibration and validation was carried out using FLAC3D.1 The models were calibrated against observed and measured performance of coal pillars and the overburden in operating mines to provide a basic set of input parameters that can be used to provide a realistic first estimate of expected ground response and pillar loading. Input parameters for modeling coal pillar response were based on data from triaxial testing on coal samples, combined with both matching the depth of failure in the coal ribs to observations as well as matching the peak pillar resistance to an empirical equation. The models were calibrated against strong roof and floor case histories in which the pillar strength is governed by failure and yielding of the coal within the pillar and the surrounding strata only had a limited impact on pillar strength. Input parameters for the overburden were determined from a large database of laboratory tests and model calibration against maximum subsidence and subsidence curvature. Further overburden calibration was carried out by matching stresses in the mining horizon to field measurements. Three examples of the application of the calibrated dataset and modeling methodology to field measurements are presented. The results show that a reasopable estimate of the in-seam stress distribution and overburden response can be obtained for both strong and weak overburden scenarios at various depths of cover.INTRODUCTIONThe planning and design of coal mine excavations requires reliable estimates of the expected strength and loading of the mine structures to achieve global stability. Empirical methods are widely used to estimate the strength and loading of coal pillars and have been incorporated into pillar design procedures, such as Analysis of Longwall Pillar Stability (ALPS) (Mark, 1987) and Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), that are widely used in the United States. ~umerical models are finding increasing application as a tool for underground mine design because of their. versatility and the ever increasing computational power available to mine designers. A prerequisite for the application of numerical models is the calibration of the models against observed rock mass response (Hoek et al., 1990; Skiles and Stricklin, 2009). The calibration process may include comparison of model results to measured stress and deformation and modifying the input parameters in a systematic manner to achieve a satisfactory agreement between the model results and measurements. Once models have been calibrated, they can be applied to evaluating similar mining layouts in similar geological conditions."

Jan 1, 2010

By Lou Gaozhong, Guo Wenbing, Zhao Gaobo, Wang Shuren

"The height of a fractured zone due to high-intensity mining (HIM) plays a vital role in the safety analysis of coal mining under bodies of water. This paper described the characteristics of HIM. The processes of overburden failure transfer (OFT) are analyzed. The state of destruction transfers from a certain stratum to the upper stratum as face advance distance increases, and the processes of OFT are divided into two stages: transmission development stage and transmission termination stage. Through theoretical analysis, the limited suspension-distance and limited overhanging distance of each stratum are proposed to judge the damage of each layer. Based on this, the OFT criteria of fractured zone development are obtained. The mechanical model of strata suspended integrity and overhanging stability are established. Finally, a new method to predict the height of fractured zone due to HIM is put forward based on the processes of OFT, the limited suspension-distance, and the limited overhanging distance. Further, a HIM panel in the Datong coal mine is taken as an example. Theoretical methods are proposed, and engineering analogy is used to predict the height of the fractured zone, which is compared with in-situ measurements reported in the literature. The results show that the in-situ measurements for the height of the fractured zone are in close agreement with the theoretical calculation result. Therefore, the rationality and reliability of the theoretical method proposed to predict the height of fractured zone is verified.INTRODUCTIONThe height of the fractured zone (HFZ) due to the exploitation of coal is a key parameter for the safety analysis of coal mining under a body of water (Wenbing, Youfeng, and Hou, 2012). Accordingly, it is necessary to predict HFZ under the corresponding mining conditions before coal mining."

Jan 1, 2018

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By Peter Fischer, Heinz-Jiirgen Kateloe, Anton Sroka, Axel Preusse

"Since mining in Germany has a long history, there are still many locations where the surface fracture problem has to be solved. Shallow mine workings from an earlier era can affect the surface in a discontinuous way. In many cases, due to light overburden load, those mine rooms did not collapse and a downfall can suddenly happen for many reasons, e.g., in connection with a changed load entry into the subsurface or by additional influence of water. This results in ground movements, which in extreme cases, appear as surface fractures.Depending on the use of the surface, ground movements caused in such a way constitute an endangerment by law. Particularly, within the southern Ruhr district, surface fracture and subsidence endangered ranges are determined on the basis of an empirical method that resulted from a systematic evaluation of surface fractures and rock disclosures. This method indicates maximum ranges within which impacts from abandoned shallow mine workings must be assumed.With a special emphasis on a risk management approach, RWTH Aachen University adapted the model of stochastic media to the conditions of abandoned shallow mining to compute and illustrate potential ground movements due to the collapse of shallow mine workings. Further investigations were concerned with the analysis of characteristic parameters which can serve for the assessment of the surface fracture probability in a comparative view of different cases. In recent years, more than 50 surface fractures in the southern Ruhr district were analyzed in order to develop a risk assessment of surface fracture endangered ranges over shallow mine workings. The results that have been obtained so far are described in this paper.INTRODUCTIONAbandoned underground mine workings of shallow depth can pose a threat to the surface. Due to small overburden rock loads, shallow excavations often remain intact for decades after the operations have ceased and may collapse abruptly (Braemer et al., 2005; Hollmann and Nuerenberg, 1972; Preusse et al., 2007). Several approaches for prognosis of surface fracture resulting from 97 subsurface collapse deal with this topic (Loebel and Sroka, 2001; Tajdus and Sroka, 2009)."

Jan 1, 2010

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By John A. Rusnak

"This paper discusses the variation of coal strength based on the megascopic coal lithotypes for Central Appalachian high-volatile A coal beds. The composition of coal beds is complex and variable, depending on the depositional environment associated with original plant material, inflow of clastic material, and water level fluctuations in the original swamp/mire environment. Thus, different types of coal and sediment are formed within each coal bed. These differences in coal composition were first classified by Marie Stopes, a paleobotanist, in 1919. The classic coal megascopic lithotypes are vitrain, clarain, and durain, which correspond to bright, bright banded, and dull coal, respectively. Stopes also identified that the lithotype fusain, which is mineral charcoal, has no inherent strength and can act as a plane of discontinuity. In this study, two other coal-bed lithologies are also considered—bone and carbonaceous shale. This makes for a comprehensive suite of coal-bed stratigraphic components apart from rock partings. A total of 1,000 uniaxial compressive strength (UCS) and 440 indirect tensile strength (ITS) tests were conducted on cores from southern West Virginia that were specifically logged and described using the megascopic coal lithotype nomenclature. Statistical analysis is presented showing the results for each lithotype group with mechanical properties correlated to the lithotype. Previous studies have analyzed the mechanical breakage properties associated with coal lithotypes, which correlate well with these results. However, coal rank does appear to be a contributing factor, and this study is confined to only high-volatile A bituminous rank. Application of these results would be well suited to a rock mass classification system to address coal pillar rib stability. This would allow for rib support design and implementation to consider relative coal strength by visual observation of the seam stratigraphy through ongoing observations within a mine. Changes in seam composition can be readily identified, allowing the adjustment in rib support design. Another application would be for the determination of numerical modeling inputs based on detailed seam stratigraphy. However, these results, even with the standard strength reduction criteria, may not be applicable to currently accepted empirical coal pillar design procedures."

Jan 1, 2017

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Bruce W. Jack

An extensive underground roof-monitoring program was conducted in order to determine the roof strata behavior under various conditions. In total 29 sites at 5 different collieries were monitored using the sonic probe extensometer. Results showed that, in drill and blast sections, there are often pre-existing openings in the roof prior to the installation of the support. An estimated 42 per cent of the total roof displacement monitored in drill and blast sections took place prior to the installation of support. A comparison between roadways and intersections indicated that, for a 40 per cent increase in the span, taken across the diagonal of art intersection, relative to the roadway width, the magnitude of the displacement in the roof increased by a factor of 3. Total displacements measured were relatively small, only 2 reaching double figures of 12 mm. The remainder were all less than 7 mm. The results also showed no evidence of a substantial increase in the height of the bed separated, potentially unstable roof strata, as is the case in the high horizontal stress-driven beam-buckling mechanism experienced in for instance some Australian coal nines. Therefore, it was concluded that, in South African collieries, the effects of horizontal stresses is generally relatively small compared to overseas collieries.

Jan 1, 2000