Search Documents

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By U. F. Beichmann

INTRODUCTION The City of Oslo together with the neighbor municipalities, Baerum and Asker, are presently building a jointly owned sewage treatment plant located on the west side of the inner Oslofjord. The project is scheduled for completion late 1981. Because the location of the treatment plant is at a distance of about 20 miles (30 km) from the city center, a discharge of more than 13 yds 3/sec (10 m3/sec.) of sewage and storm water will have to be transported over considerable distances. The topography of the area and the geological conditions early indicated that the only realistic transport method had to be through tunnels. As planning proceeded, full face tunnel boring emerged more and more as a favorable alternative to conventional drill and blast medhods. Today the scheme comprises nearly 25 miles (40 km) of tunnels being excavated by full face tunnel borers. In addition a number of access tunnels and cross cuts are to be excavated by conventional methods.

Jan 1, 1979

By Robert E. Goodwin

There are four main requirements which must be considered when selecting a wire rope for the best serviceability. A proper choice is made by correctly estimating the relative importance of each of these requirements and selecting s rope which has those qualities best suited to withstand the combination of destructive forces expected under continued service. A wire rope should possess: 1. Strength sufficient to support the maximum load expected and with s proper safety factor. 2. Ability to withstand bending and to resist bending fatigue without failure of the wires. 3. Ability to withstand surface abuse such so abrasive wear, pounding, and wire scrubbing. 4. Ability to withstand abuse such as crushing and distortion.

Jan 1, 1968

By Don Rose

I. INTRODUCTION The Atlanta Research Chamber is an UMTA-sponsored applied research facility studying tunnel design, excavation and support systems. It is located directly below Peachtree Street in downtown Atlanta, Georgia. It is included in the CN-120 contract to build the Peachtree Center subway station, a part of the Metropolitan Atlanta Rapid Transit Authority (MARTA) multi-billion dollar "Phase A" 53-mile transit project, which is 80 percent funded by UMTA with 20 percent provided by local authorities in Atlanta and Fulton and DeKalb counties (Figure 1). The Research Chamber is located immediately south of the main Peachtree Center Station cavern, and is in part an enlargement of the pre-existing Pilot Tunnel excavated to provide bidders on the CN-120 contract a view of the rock conditions (Figure 2). The Research Chamber lies some 3 meters above, and is approximately parallel to, the twin Running Tunnels. The Research Chamber is 18 meters long and has the same 5.5 meter diameter horseshoe shape design dimensions as the twin Running Tunnels.

Jan 1, 1979

By Ken J. Fair, Vicken H. Aprahamian, Gus Van Weert

A consortium of Canadian mining companies, engineering firms and the Ontario Government has supported Hydrochem's efforts in the last year to design and cost a 10 tpd NITROX PROCESS® demonstration plant. A 5 kg per hour mini plant was installed at the Hydrochem facilities in Brampton, Ontario. This paper describes design testwork on Dickenson Mines arsenopyrite concentrate and application of the findings to the demonstration plant flowsheet. The control of nitrates in discard solids and stack gases is discussed in detail. Nitric acid oxidation of arsenopyrite results in significant ele- mental sulphur formation, enough for it to be detrimental to sub- sequent cyanidation. Flowsheet variations aimed at dealing with this process characteristic are discussed and testwork results on one option (hot liming) are described.

Jan 1, 1988

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980

By R. Y. Wan, J. D. Miller

Thiohydrometallurgical systems including thiosulfate, thiocyanate and thiourea have been stud- ied as alternative liriviants for the leaching of gold. Research and development of thiohydrometallurgical technology has been prompted by environmental concerns with the use of cyanide and problems associated with the processing of difficult-to-treat ores. These thiosystems have some chemical similarities, enabling gold to be leached in a practical oxidizing environment. However, the solution chemistry of the thiosystems is complicated due to instability of the thioreagents and many other reactions which occur during the gold leaching reaction. In this paper, interference reactions of selected metal ions and sulfide minerals are examined in order to understand important aspects of solution chemistry which control the stability of the thioleaching reactions. Applications using thioreagents as lixiviants for oxide and refractory gold ores are presented.

Jan 1, 2005

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

By David Brown, Glen Hall, Ken DeVos, Frank Barone

Dredging and Flooding was completed on the Falconbridge Limited "New Tailings Area" in the period from 1996 through 1998, as part of their site closure measures. Part of the decision making process and closure planning was water quality prediction, including oxidation and diffusion modelling. The purpose of this modeling was to define the potential water quality that would result during and after dredging. A significant body of research on the geochemistry and oxidation kinetics of this site had been compiled. The results of the modeling provide practical insight on the potential water quality that may be expected. Water quality in the pond has steadily improved since flooding was completed with the exception of short term peaks during spring runoff. Aquatic vegetation is appearing through natural recovery and transplanting of local species, and colonies of minnows are now observed in the ponds.

Jan 1, 2000

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By Simon D. Strauss

This paper discusses the ways in which the metals industries dealt with surplus capacity in the past, primarily the twenty years, 1950 - 1970. During this period, the bulk of metals production in the market-economy countries was controlled by private sector companies. Since then, public sector companies have played an increasingly important role in the metals industries of the market-economy countries. Of course, the change was not overnight. It occurred gradually over a period of many years. Indeed, by 1965, several developing nations had adopted policies of government control of metal operations previously in private hands. The metals industries are so many, so large and so diverse that the constraints of time make it impossible to deal with all segments. To illustrate the problems of surplus capacity in the metals industries during the period, this paper focusses primarily on three metals. One experienced rapid market expansion between 1950 and 1970; one had a growth more or less in line with the expansion of the world economy; and one lagged well behind the pace of industrial expansion. No one will be surprised if aluminum is identified as the metal with rapid growth; copper is identified as the metal that kept pace with the world economy; and tin is identified as the laggard. Individual computations of the rate of growth for these metals show some variations, but most estimates place the increase in aluminum consumption in the market economy countries between 1950 and 1970 at a compound annual rate of about 8%. The corresponding figure for copper is a compound rate of 4%. Tin consumption showed no growth. A widely accepted point of view is that sharply rising demand will force the price of a commodity to increase substantially in order to attract a necessary expansion of supply. The corollary to this is that stagnant demand will hold prices down, as there is no need to stimulate new supply and it may be necessary to force marginal producers out of the market. The experience with aluminum, copper and tin in the years 1950-1970 does not support this theory. In 1950, the average prices in the United States market as reported by the American Bureau of Metal Statistics were 17.74 a pound for aluminum, 21.24 a pound for copper, and 95.54 a pound for tin. The corresponding figures in 1970 were 28.74 a pound for aluminum, 57.74 a pound for copper and 174.24 a pound for tin. Aluminum, with the greatest market growth, rose by 60%, whereas tin rose 82% and copper by 172%. Clearly, other factors were a more important influence on price than was the trend of demand To revert now to the capacity issue, during the period under review aluminum demand was rising so sharply that that industry had no sustained problem with surplus capacity. Instead, if anything, capacity may at times have been a constraint on demand. The industry succeeded in attaining explosive market growth through imaginative research and promotion programs. Some of this growth was the result of substitution of aluminum for other commodities – steel, copper, wood and glass as examples. But much of the growth was the consequence of developing entirely new products through technological innovation. Prior to World War 11, the number of aluminum producers was extremely limited. Alcoa and Alcan in North American and Pechiney and Alusuisse in Europe were the dominant firms. The developing countries had virtually no production and in Japan and Germany production was only a small fraction of the North American output. During the War years the United States had financed the construction of many new facilities. After the war these plants were sold by the government to Reynolds and Kaiser in order to foster more competition in the market. Subsequently many other concerns became aluminum producers, both in the United States and elsewhere and competition for markets intensified.

Jan 1, 1989

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By C. D. Taylor, A. L. Mazzella, A. L. Martikainen

In fluctuating airflow, continuous air velocity recording is the most reliable method of air velocity measurement. It allows for fast recognition of changes and the calculation of long-term averages. Also, it enables the mine operator to identify when the airflow has decreased to a point requiring action. Using ultrasonic anemometers provides an accurate option for continuous air velocity monitoring. This paper provides information about the effect of common obstructions in underground mining on air velocity readings. Stationary and moving obstructions are used to represent workers and equipment that would cause discrepancies in measured airflow. Also, it is important to know how large of a sample size is required to ensure reasonable accuracy of results. Statistical analysis is used to evaluate the required sample size. The sampling procedure is further studied by comparing two different sample rates. The results show that obstructions provide noticeable differences in air velocity measurements. Also, movement of obstructions can be recognized from changes in results. Surprisingly small sample sizes provide reliable air velocity information. Standard sample rates are found to be suitable for the underground environment.

Jan 1, 2011

By B. A. Firth

Australia is the largest exporter of coking and thermal coal to the international market. This market has required that the coal being presented to the customer has a particular level and consistency of quality. In this context, the Australian industry has developed coal preparation practices that allow this criteria to be met while maximising the recovery of coal from the resource. This has required on- going developments in both coarse and fine coal cleaning technology over the past 30 years. Coal flotation has undergone a number of developments with regard to maximising recovery from the overall plant circuit. This includes innovative flotation circuits (split feed), methods of enhancing the use of reagents and control of pH. During the 1990s, there have been major changes in flotation as practised in Australian coal preparation plants. Columns have become the preferred technology for both greenfield developments and plant upgrades. This paper will outline the above developments with a number of plant examples and the reasoning that has driven the change. The ongoing research that is being carried out on new cells to optimise the overall fine coal circuit will also be discussed.

Jan 1, 1999

By E. V. Manlapig, B. K. Gorain, N. W. Johnson, K. Ward

A flotation model developed at the Julius Kruttschnitt Mineral Research Centre was used to predict the performance of copper rougher and scavenger circuits at the copper concentrator at Mount Isa Mines. The model describes the kinetic response of an ore in a flotation cell in terms of ore floatability, cell characteristics and froth recovery. The floatability parameters of the rougher feed ore were obtained directly from a detailed plant survey. Flotation analysis was carried out for twenty different size-by-liberation classes to account for the effects of particle size and liberation on flotation. This paper investigates the capability of the model to predict the flotation behavior of 20 different size-by liberation classes in the rougher and the scavenger banks.

Jan 1, 2000

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is overcompacted. Research has shown that excessive compaction in replaced growing media is detrimental to the establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky developed test cells on reclaimed areas at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. Each test cell was planted with various species of trees, and for the first two years of tree growth, data were collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data were statistically correlated to determine how ripping affects the relationship between soil compaction and tree survival rate.

Jan 1, 2003

By R. Corriveaau

This paper is about a horizontally curved conveyor, which carries 6,050 stph of limestone over land from a new quarry to the owner's plant. The conveyor is 5,012 ft long with a horizontal curve radius of5,OOOft Site conditions made a curved conveyor design the most optimal and economic solution. Using our unique custom conveyor calculation program, TKRI was able to accurately model and design the conveyor to properly track the belt and prevent any spillage through the horizontal curve radius. A data monitoring system was installed that allows monitoring of the conveyor both locally and remotely. The remote monitoring allows TKRI to contact the owner for preventive maintenance. Preventive maintenance can reduce the conveyor downtime during normal operating hours.

Jan 1, 2004