Search Documents

By L. "Andy" Anderson, Stephen N. Short, James E. Friant

Since the introduction of "boxhole" drilling in South Africa in 1973, the concept of a blind raise, drilled upward from below, has become an accepted mining practice. A combination machine, capable of constructing raises to a mining level below, or blind raising upward from a single setup position adds a further dimension in versatility. A machine with these dual operating modes was designated by The Robbins Company as the 53R and was introduced into the Western Deep Level Mines, South Africa in 1984. The unit is powerful (200 hp) and compact (18,000 lbs., in a 10 ft x 4 ft 5 inch x 4 ft 6 inch package). This paper describes the design considerations for the new machine, provides field data from early trials, and looks briefly at its overall market and potential.

Jan 1, 1985

By Antonio Nieto

According to the analysis of surface powered haulage accidents involving off-highway haul trucks in openpit mining, the U.S. Mine Safety and Health Administration (MSHA), reported 1,300 fatal accidents from 1990 to 2005. Of these, 163 were considered off-highway truck haulage accidents, and at least 23 involved collisions of an off-highway truck with a neighboring vehicle or a worker on foot (Nieto and Dagdelen, 2006). In general, an average of 18 nonfatal accidents and three fatal accidents occurred in openpit mining per year when equipment backed over the edge of an embankment, stockpile or dump point (Fessak, et al., 2003). The specific problems that need to be solved can be determined by carefully studying the accidents involving haulage trucks (Marrara, et al., 2004). Solutions to haulage truck safety must consider the human factors affecting each task even when engineering solutions seem most appropriate. In surface haulage, human performance becomes a critical issue because of the unusual demand the vehicle?s places on their human operators: ? Roadways and working areas change frequently in mining operations. ? The sheer mass of mining equipment such as trucks requires control inputs (e.g., braking) far in advance of the desired action. ? Rough roads, loading and unloading impacts can subject the driver to dangerous shocks and vibration. ? Visibility is sharply curtailed by the bulk of the vehicle generating large blind spots. All of the above issues can be attributed partially to the lack of visibility (Pyles et al., 2003). Driver visibility and communications are key issues to reduce mining truck accidents. Analysis of fatalities and injuries involving mining equipment demonstrates the need to develop new intervention and control strategies to mitigate the risks associated with mining equipment operation. Ongoing development of these and other new strategies is required to achieve a reduction of injury in the mining industry

Jan 2, 2010

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By Robert Rennie, Taylor Davies, Ahsanul Rafi

Electric locomotives powered by extensive electrical cabling systems were prevalent in the mining industry in the early days of the 20th Century [1]. Since the movement of tethered electrical mining locomotives was limited, the advent of diesel-powered mobile mining equipment provided more flexibility. This led the mining industry to be dominated by diesel-powered locomotives for most of the 20th Century and the entire 21st Century, to date. However, diesel power has certain drawbacks. Diesel-powered vehicles produce tailpipe emissions such as diesel particulate matter, carbon dioxide, sulfur dioxide, and nitrogen oxide. Mine workers exposed to these emissions were, and continue to be, subject to health issues such as respiratory problems, increased risk of lung cancer, and cardiovascular disease. [2][3]. Extensive ventilation systems are required to dilute the diesel exhaust and dissipate the heat generated by these vehicles. Moreover, as mines are getting deeper due to depleting resources, ventilation costs in diesel-powered mines are becoming increasingly high. These factors, coupled with the trend towards greenhouse gas (GHG) reduction in mine operations, has allowed zero-emission electric locomotive systems to gain traction. As lithium-ion battery technology is becoming more advanced, battery-powered electric vehicles can now perform duty cycles comparable to those of diesel-powered vehicles. Although battery-electric vehicles (BEVs) are comparable to diesel-powered vehicles in terms of mobility, they have certain limitations. For instance, the amount of onboard energy is limited by the battery energy density and specific energy. The MT42 diesel haul truck from Epiroc, for example, has a fuel tank capacity of 580L, which is equivalent to around 1450 kWh of net electrical energy [4]. The electrified version of the MT42, on the other hand, has an onboard battery with 375 kWh of usable energy weighing around 4.9 metric tonnes [5]. Moreover, storing and refueling of diesel-powered vehicles is simple and quick, whereas battery energy storage and charging systems require extensive infrastructure development. Charging time is mostly limited by battery chemistry and design. Due to these limitations, the benefits of battery-powered mining vehicles are more likely to be realized with proper planning and optimization of the BEV fleet. This includes optimizing mining layouts for BEV use, charging infrastructure design, and management of onboard energy storage systems.

Jun 25, 2023

By L. A. Arrington-Webb

Forty-four states produced clay products during 1994 for a total value of $1.6 billion. This was a 3% increase in total tonnage and a 7% increase in value from 1993. Kaolin Domestic production of kaolin during 1994 was estimated to be 9.3 Mt (10.2 million st), according to the US Bureau of Mines (USBM). Georgia remained the leading producer with 7.5 Mt (8.2 million st), followed by South Carolina with 535 kt (589,000 st). Kaolin used as a paper coating or filler pigment accounted for 51% of domestic consumption. Other uses included grogs (14%), fiberglass (5%) and plastics (4%). A reclassification by an Alabama producer of fire clay to kaolin accounts for the introduction of kaolin used in grogs. This also accounts for the apparent decrease in the use of kaolin in paper from 60% in 1993. However, the actual amount of kaolin used in paper was the same.

Jan 1, 1995

By D. R. Rathburn

Jan 1, 1962

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By Diane Jones, Jeremy Spearman, Tom Matthewson

Requirements for minerals are on the increase globally and the deep sea offers a potential source of essential materials. Extracting these minerals from what is considered an environmentally sensitive area, and one about which little is still known, is a challenging activity, which needs careful consideration and an appropriate environmental impact assessment to be carried out. Extraction of material from the deep sea beds can cause disturbance or damage to benthic communities; impact on mobile marine species such as fish, mammals and reptiles; cause increases in suspended sediment and sediment deposition onto potentially sensitive areas or potentially release contaminants which were previously bound to the sediment. This paper discusses the potential environmental issues surrounding extraction of deep-sea deposits using aggregate dredging techniques and how those issues can be appropriately assessed. In particular issues of suspended sediments, plume transport, water and sediment quality and underwater noise impacts on potentially sensitive species and habitats will be explored.

Sep 1, 2014

By Steve Kral

Amax Coal Industries Inc.'s Delta Mine is a medium-sized. high-sulfur coal producer that has lived up to the challenges posed by nearly six decades of a highly competitive domestic coal market. The mine now faces one of its biggest challenges - the same one staring at the dozens of other high-sulfur producers in the Midwest - the Clean Air Act Amendments of 1990. The 59-year-old mine, located in the coal fields of southern Illinois, has remained one of the state's oldest continuously operating mines by rolling with the ups and downs of the coal market and by incorporating new technologies and innovative productivity improvements into its operation.

Jan 1, 1993

By F. B. Henderson

1.0 PROLOG Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

By Anna Kate Miller, James J. Brady, Hamza Jaffal, Ritika Sangroya, Chadi El Mohtar, Wing Shun Kwan

"The design of an appropriate pre-grouting program can be the difference between a successful tunnel construction and an expensive on-the-go repair. However, current grout design relies heavily on rulesof- thumb and outdated charts. The geotechnical investigation is rarely targeted towards grouting design and the final grouting decisions are made based on fines content or soil classification. The current paper presents an experimental study performed to determine the optimal grout for a tunnel in soft ground below the ground water table (GWT). The testing program consisted of sieve analysis and undrained static triaxial tests on reconstituted sonic samples. Rheological tests were used to compare the different grout mixes and identify best candidates before performing one-dimensional permeation tests. Pressure and volume measurements during the permeation tests, along with the unconfined compression strength results on the permeated soils, helped evaluate the filtration potential for the different grouts and select the optimal grout.INTRODUCTIONConstruction of the Millwoods Double Barrel Replacement Project commenced in 2009 and was expected to be completed by 2015. To facilitate ongoing city development in south Edmonton, the City implemented construction of a major sanitary trunk network along 91st Street and 30th Avenue. The project involved the design and construction of approximately 1.2 miles (2 km) of 7.8-ft (2,400 mm) sanitary tunnel and 2.1 miles (3.4 km) of 11.5-ft. (3,500 mm) and 9.5-ft. (2,900 mm) storm tunnel. Part of the project also involved the conversion of the existing double barrel storm and sanitary trunk to full sanitary service, and reconnecting the local storm sewers from the double barrel pipe to the new storm tunnel. The tunnels range in depth from 26-ft. (8 m) to 115-ft. (35 m) and are being installed using a one pass system with precast concrete segmental liners."

Jan 1, 2016

By Daniel N. Adams

The University Link project extends Seattle?s light rail from downtown to University of Washington (UW). It includes 5.0 kilometers (3.15 miles) of twin-bored, 6.4 meters (21 feet) excavated diameter tunnels, and two cut-and-cover stations. The Capitol Hill Station (CHS) requires an excavation 170.7 meters (560 feet) long, 22.6 meters (74 feet) wide, and 22.9 meters (75 feet) deep. The University of Washington Station (UWS) requires an excavation of about 238.4 meters (782 feet) long, 21.3 meters (70 feet) wide, and 33.5 meters (110 feet) deep. The project is within the glacially diverse soils of the Puget Sound region, below groundwater. This paper highlights major station and tunnel design elements, including the approach to support of excavation at both station boxes, and the site staging requirements.

Jan 1, 2008

By Ian Mitchell, Peter Faganl, Paul Haddad, Rob Dunne

During the gold cyanidation process, cyanide can be lost from the leachate by various chemical routes. The products of these cyanide losses include base metal cyanide complexes, thio­cyanate and cyanate. These losses are particularly important when treating pyritic or cupriferous ores since the two most sig­nificant cyanic ides, in order of importance, are sulfides and cop­per bearing minerals (I). Cyanidation of pyritic minerals results in the formation of thiocyanate. The problems caused by cyanide soluble copper minerals are well known to the gold processing industry and have been reviewed by several authors (e.g. 2, 3). An important consider­ation, especially with a number of more recent leaching tech­nologies, is the effect of the CN :Cu mole ratio, R, on the gold leaching kinetics. In order to efficiently leach cupriferous ores, it is important that R is maintained at a level that allows suffi­ciently rapid leaching without excessive use of cyanide. The optimum value for R in a fixed leaching system would appear to lie between 3 and 4. This is based on the early observations that the leaching rate is very slow when R is below 3, with a rapid increase in the leaching rate above 3 (2, 3,4). The leaching rate increases gradually when R is greater than 4 (4). The major Cu(I)-cyanide complex in this range of R values is the [Cu(CN)J]2· species. It has been postulated that leaching occurs due to either uncomplexed cyanide or the fourth ligand in [Cu(CN)4]3·, since the stepwise formation constant for this complex is very small (2, 3). An additional consideration when leaching cupriferous ores is the oxidation of cyanide by Cu(II) minerals, resulting in the formation of cyanate. It has also been reported that both sulfide minerals (5) and activated carbon (6, 7) catalyse the oxidation of cyanide to cyanate. From the above discussion, it is important for the leaching con­ditions to be carefully controlled when treating pyritic and cuprifer­ous ores in order to achieve efficient and economically viable leach­ing. For example, large concentrations of thiocyanate in the leachate would reveal large cyanide losses and thus indicate the need for a pretreatment step to oxidize the sulfides. Alternatively, a low R value would indicate slow leaching kinetics and consequent low gold recoveries, indicating the need for increased cyanide dosage.

Jan 1, 1996

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By Ross W. Smith

Many studies have been made of the microflotation of quartz (1,2,3,4,5,6) and alumina (3,5,6, 7,8) using various anionic and cationic hetero- polar hydrocarbon surfactants as collectors. A few studies have been made on these minerals using amphoteric hydrocarbon collectors ( 9,10, 11,12) and only a few studies have been made on the use of fluorocarbon surfactants as flotation collectors (13,14). The present investigation compares microflotation response of the two minerals in hydocarbon and fluorocarbon collector systems of the anionic, cationic and amphoteric types. An attempt is made to relate flotation response of the minerals to their electrokinetic behavior and the pKa values of the collectors.

Jan 1, 1979