Search Documents

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By J. C. Adams

Although explosives constitute only a small portion of a mine's total cost, the relative success of each blast has a tremendous effect on subsequent activities such as excavation, crushing, and equipment maintenance. Beginning in January of 1993, tests were carried out to determine whether productivity could be improved by replacing standard ammonium nitrate fuel oil mixtures (ANFO) with a high density, high performance blasting agent. The study was carried out at gold mines, coal mines, and cement quarries in Nevada, California, Colorado, and New Mexico. A wide variety of rock types and blasting conditions were encountered. Results showed that at most operations productivity was sufficiently improved to more than offset the increase in explosives cost. This resulted in a net reduction in mining cost. This paper presents a summary of these results.

Jan 1, 1996

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.

By F. C. Bond

Nature of Empirical Calculations The size reduction of large tonnages of ore and rock is an operation of great magnitude. It is a necessary and important part of industry. Its development has been motivated by practical need and has followed the path of an industrial art without much help from theoretical science. Knowledge has been accumulated from experience. Trial and error established the methods; then collected data were tabulated and served as the basis for empirical equations that have been continually modi¬fied and amplified as new data became available. These equations now constitute the bulk of our present knowledge of comminution. There is no accepted scientific theory that is basic to comminution. In electrical, mechanical, and civil engineering, as well as in many other industrial activities, such theories exist and are extremely help¬ful, but rock is essentially heterogeneous, and the zones of weakness that control its breakage are thoroughly diversified. No theory has yet been discovered which can account for the variability of rock, although many attempts have been made. Empirical equations tell nothing of the why of a phenomenon, but if they are properly derived they can tell much about the how. They always represent only an approximation of behavior but never a law. In a proper empirical equation a symbol is assigned for each of the variable quantities that obviously affect the relationship. In a grinding mill these include mill diameter, mill speed, and feed rate among them. In setting up and revising an empirical equation the cardinal princi¬ple in establishing and modifying it is this: any change must be strictly ascribed to the variable which caused it. A useful empirical equation is rendered useless when a change in any convenient coefficient or exponent is made to make it fit a particular set of data, without certainty that the altered coefficient or exponent is the responsible variable in the new data. Such indiscriminate revisions have brought the use of empirical equations into some disrepute. When existing equations are changed to accommodate new data it is a good rule to make a change which gives results intermediate between the new and the old. A halfway point is usually a good choice.

Jan 1, 1985

By D. R. Tweeton, L. W. Lake

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of ground-water quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be per¬formed in two or three weeks. It is relatively inexpensive, requiring one injection-production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin and was partially funded by the US Bureau of Mines.

Jan 1, 1987

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By Anshumali Gangwar

This paper outlines the chance constrained binary integer program developed by the author in his doctoral dissertation at Columbia University, New York, 1973. The optimum planning of a mining program involves the determination of a production schedule which maximizes the net present value of the mining property. The actual mining process has an inherent stochastic and discrete nature. In particular, the demand for the mined product and the grade of the mineralized material in the ore are the two most important stochastic mining variables. The decision to mine or not to mine any block of a mining property is a binary integer variable. This paper outlines the formulation of pit production scheduling problem as a chance constrained binary integer program. The deterministic equivalents of these chance constraints are nonlinear in binary variables which have subsequently been linearized. The planned objective is to meet with a stipulated high degree of reliability, all the random demands as they materialize with a random supply of the commodity being marketed as determined by the eventuating random grade values of the exposed ore blocks and the mining system's production constraints such that the discounted total production costs over the entire planning horizon are minimized or the profits maximized. The emerging surface of the mine in each scheduling period is determined by the values taken by the binary decision variable associated with each block of material in each scheduling period.

Jan 1, 1982

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By M. L. Nave, R. E. Melley

DC motor drives are available technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of DC drive features. The purpose of this paper is to familiarize and inform possible mining users of DC drive attributes.

Jan 1, 1996

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By A. Pinches, R. Winby, P. J. van Staden, M. K. Rhodes, P. C. Miller

This paper is a progress report on the commercialization of using bioleaching for base-metal concentrates. The paper focuses on bioleach processes for recovering copper from chalcopyrite and nickel/cobalt from pentlandite/pyrrhotite. Data is discussed from pilot-plant trials in which an overall recovery >95% was obtained for the bioleaching of copper from chalcopyrite. The pilot plant was operated in closed circuit with solvent extraction and electrowinning circuits for final metal recovery. For the bioleaching of nickel and cobalt from pentlandite/pyrrhotite, an overall recovery of 97% was achieved. Precipitation routines were used to produce a final nickel/cobalt product. The pilot plants were capable of treating a few kilograms of concentrate per day. Prominent features in the design of a 1-t/day (1.1-stpd) copper-bioleach demonstration plant for the treatment of chalcopyrite concentrate are discussed. The plant, which is now under design, will be constructed and operated based on the results obtained from the laboratory pilot-plant campaigns. Issues of scale-up for the demonstration plant, together with integration into upstream and downstream processing, are also addressed. Independently derived capital and operating costs are presented for a possible commercial plant. These cost studies indicate the principle economic issues in considering the application of bioleaching to the extraction of base metals. The benefits of bioleaching complex concentrates that are not amenable to physical beneficiation and economic treatment by conventional smelting are highlighted. Issues, such as the environmental aspects, that illustrate the benefits of bioleach technology are given.

Jan 1, 2000

By Mark E. Gershon

Conventional methods of drillhole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drillholes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drillholes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1983

By Paweł Stefaniak, Natalia Duda-Mróz, Sergii Anufriiev, Wioletta Koperska

Due to the high environmental risks and negative impact of a failure, tailings storage facilities (TSFs) need constant monitoring. Advanced mathematical models have been developed in the past to predict the behavior of TSFs and raise alerts if needed. To be precise and reliable, such models need a spatial distribution of soil types within the dam as an input. Getting this data from laboratory measurements is time and costconsuming. In this article, we propose an ANN-powered algorithm, which allows us to accurately estimate the soil distribution based on a cone penetration test (CPT).

Jun 25, 2023

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969

By W. M. Houston

The phosphate formations of the Pliocene epoch were deposited along the coastal shelf of the eastern seaboard. The deposition of the phosphate is thought to be somewhat contiguous along the early shoreline, and the deposit can be more or less traced over an 800 to 930 mile path from the Florida Gulf Coast, near Ft. Myers, to the Pamlico Sound of North Carolina. This is illustrated in Figure 1. Three areas of commercial importance are currently being exploited from this extensive known deposit: 1 - The so-called ?Bone valley? in Central Florida (multiple operations) 2 - Hamilton County in North Florida (Occidental Corporation operation) 3 - Beaufort County in North Carolina (Texas Gulf Sulphur operation)

Jan 1, 1966

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986