Search Documents

By C. B. Clemmens

Accurately predicting ground control conditions before mining requires a comprehensive exploration approach including photogeologic mapping (satellite and low altitude), delta modeling and, particularly, geophysical logging. In situ properties, density; strength indices; grain size; clay content; and aquifer location, can be estimated with this inexpensive technique. Geophysical measurements can be spot-checked by field or laboratory tests on core samples and by hydrologic (pressure) testing. Each phase of drilling should be accompanied by refinement of the delta model, facilitated by log signatures. Measured properties can then be projected into geologically similar areas. A properly planned program will delineate both the "worst-case" and normal support conditions. Suspect areas can be avoided by mine layout and the mine plan can contain support contingencies for anticipated trouble spots.

Jan 1, 1985

By S. Maurigiannakis

In an effort to promote sustainability in the construction industry, the natural decorative stones that cover large external areas of buildings may be replaced with artificial stones. In this paper the physical and mechanical properties of artificial decorative stones are presented and are critically compared with corresponding natural stones. To test suitability for various applications, artificial stone specimens were subjected to weathering testing (freezing-thaw cycles in a climatic chamber). Mechanical characterization of these specimens was based on uniaxial compressive testing as well as non-destructive ultrasonic testing. Preliminary results show that artificial stones can replace natural stones, thus creating a sustainable development option for the construction industry.

Jan 1, 2003

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1984

By Harold Potter

(1) A great deal of experimentation has been carried out by the Wet Process Cement Manufacturers in connection with additives which make possible the production of a pumpable slurry at reduced moisture contents. We ourselves have made dozens of tests both at Laramie, Wyoming and Monolith, California. (2) The viscosity or pumpability of a slurry at a definite moisture content and fineness seems to depend on two basic phenomena. One is the physical structure of the raw material itself, which on fine grinding may or may not be excessively hydrophilic (water adsorptive). Usually crystaline or glassy raw materials are non- hydrophilic. The fine grained amorphous raw materials such as shales and clayey limestones very frequently are, however. (3) The second basic phenomenon affecting the hydrophilic tendencies of the raw material is the presence of certain soluble salts, especially gypsum and small amounts of alkalin carbonates or oxides. (4) Various soaps, and phosphates can be used to produce a pumpable slurry of low moisture content when using hydrophilic raw materials as well as can other proprietary materials such as certain long chain carbon compounds. Too frequently however, the price of such additives in conjunction with the amount required prohibits their use in the cement industry.

Jan 1, 1959

By Warren E. Morrison

The expansion of the United States economy in the postwar period has had a tremendous impact on the demand for energy. Not only has total energy consumption increased at an unprecedented rate, but there have been major shifts in the composition or mix of energy resources within the end-use sectors. Because of the numerous interrelationships between substitutable energy resources and their markets, the energy economy can only be analyzed in terms of the trends of its component parts. This problem takes on additional complexity when attempting to chart the nation's future energy requirements. Total energy consumption can be forecast with reasonable accuracy for periods up to 15 years by relating this to projections of economic indicators. However, forecasting the component parts of the energy economy constitutes a dilemma in that the sum of the projected parts frequently exceeds predictions for total energy. Areas of uncertainty in energy forecasting tend to mount rapidly when proceeding from total energy to the consideration of specific energy resources consumed as fuel, power, or raw materials.

Jan 1, 1965

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By Gunnar Nord

Shifting ground conditions when tunnelling often call for different methods of attacking the tunnel face. In order to overcome problems with local unstable soft ground in a hard rock tunnelling project the Boodex method offers a cost effective alternative. Boodex and variants of it is a combination of two well-known techniques, drilling with Boomer rig using Odex gear. It will give a steel lined hole ready for grouting and the steel pipe has a load bearing capacity that means that a spiling effect is achieved. In this paper the method and some applications will be described with possibilities and limitations.

Jan 1, 2003

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

Coal has traditionally been an integral part of life in Kentucky. Coal mining produces a large part of revenue for the Commonwealth of Kentucky and provides a significant number of jobs to the residents of eastern (less in western) Kentucky. Recently, however, the coal industry of Kentucky has had to endure many hardships. The Clean Air Act set forth sulfur dioxide emission standards which have severely affected much of the coal mining industry in Kentucky, because much of the coal mined in Kentucky has a high sulfur content. In this paper, the background around the effects of Clean Air Act on the coal industry is introduced. The economic and social effects of the Clean Air Act on the Kentucky coal mining are addressed.

Jan 1, 1993

By Christopher J. Bise

The potential of the coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints which have tended to limit the development of these reserves which can only be deep-mined are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short- term the industry has to incorporate presently available equipment which were not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment that are in use today and their possible application to thick-seam mining. The paper also addresses the various ground control and safety considerations that are unique to thick-seam extraction.

Jan 1, 1981

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

By K. Anim, C. Calderon-Arteaga

Located in Mojave, CA, The Soledad Mountain mine is an Open pit Heap-Leach gold Mine, which is operated by Golden Queen Mining Company LLC. under private capital. Open pit mining began in 2015 while full production was reached in 2016. The open pit mine feed a processing plant that can process more than 13K tons per day of ore which is sent to a heap leach pad. The Soledad Mountain project is a poly metallic deposit with Au and AG being recovered as payable metals. As the mine became bigger after moving to the east pit phases, Golden Queen was facing new challenges to control the production and accurately determine KPIs to improve/increase the production. To maximize returns and asset value, a new fleet management system (FMS) was adopted and implemented. The new FMS has enabled the mine to interconnect the different stages of the mining, as well as to recognize issues and implement the necessary corrections. With the associated increase in complexity in the process, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery. Implementation of new daily and weekly plans were needed to ensure the ore delivery and meeting the tonnage goals, while allowed the equipment operators to better geolocate and to maximize the equipment production. These conditions alongside with Golden Queen’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route the material from the mine, is critical to site success and some of these challenges have been overcome by the adoption of the new FMS, the implementation of daily and weekly plans and upgrades in the ore control workflow. Examples of how the integration of the new systems allowed golden Queen to improve production strategy, are discussed in this article.

Mar 2, 2022

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979