Search Documents

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By Richard Giffen, Michael Trabold, Pablo Lemus

"As part of the new 2nd Ave Subway Project, an existing tunnel constructed in the 1970’s will be connected to the new subway and used as new running tunnels. The existing tunnel had to be modified to comply with newer structural and fire life safety codes and to be connected to the new cut and cover station at 96th St. This paper will discuss the complexities of tying an existing tunnel constructed over 40 years ago into the new station and allowing for movements due to the unloading of the existing tunnel and the differential settlement of the two structures during both the construction and permanent condition. Topics that will be discussed include structural analysis, ground improvement techniques, selection of support of excavation walls, working in contaminated soil and instrumentation and monitoring of the structures. It will also cover retrofitting the tunnel to comply with updated Fire/Life/Safety requirements. PROJECT OVERVIEW The Second Avenue Subway (SAS) will be the first major expansion of New York’s subway system in over 50 years. To be constructed in four phases, it will run from 125th St. in Harlem to Hanover Square in the Financial District (see Figure 1). For most of its length, the alignment is directly under the Second Avenue roadway."

Jan 1, 2016

By Gerald Zink

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed small-hole drill has been fabricated and tested in the laboratory. High priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure high-speed swivel feeds water to the bit at about 4 1/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40 kw capacity (30hhp) Results of recent full-scale laboratory testing are presented.

Jan 1, 1978

By G. Récoché

For the African continent promoting a sustainable utilization of its mineral resources could be considered as a key determinant to fight against poverty. Sustainable development performance indicators for measuring the economic, environmental and social impacts of mining activity are necessary for drawing up policies and sectoral actions, identifying and controlling risks, identifying and implementing sustainable development actions, negotiating between stake-holders, improving mine production, etc. To respond to this need, the SIGAfrique Network proposed to develop a joint decision support tool entitled the African Mining Observatory (AMO) and, to this end, develops a system of indicators to be integrated within the SIGAfrique database. The development of both the OMA and the indicators is based on a participatory method within the working groups, which comprise experts/participants from the 13 SIGAfrique partner and observer countries (Guinea, Burkina Faso, Mali, Tanzania, Niger, Mozambique, Kenya, Uganda, Senegal, Angola, Madagascar, Ethiopia, and Mauritania).

Jan 1, 2007

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By Tom Plouf, Deepak Malhotra

INTRODUCTION The U. S. mining industry experienced a severe recession in the early 1980's. This resulted in the realization that the domestic mining industry had to compete on a global basis and only the strong or the low-cost producers would survive. The economic viability of a mining company not only depended on maximizing mineral recovery but also on its ability to do so at minimum cost. Companies had to become more productive not only by cutting costs, but also by developing and/or evaluating new technologies in existing or new plants. Several innovative concepts, including in-pit crushing and conveying, fine crushing, improved classification equipment, flotation, column flotation, pressure filtration, etc., have been developed in recent years. This paper addresses the impact of new flotation concepts and equipment on mill design. MILL DESIGN PHILOSOPHY Modern mill design, especially for large capacity plants, has its foundation in minimizing capital and operating costs. Capital costs can be minimized by minimizing the various components of the capital cost: infrastructure, equipment, instrumentation, structural, initial spare parts costs, etc. All these costs are minimized by simplifying the mill design and/or process flowsheet. The simplified process flowsheet, where applicable, consists of a single stage primary crusher followed by a semiautogeneous - ball mill grinding circuit to produce feed for a flotation circuit. Multiple flotation circuits have been eliminated in most cases. These concepts minimize the cost and encourage the use of large capacity equipment while maintaining optimum metallurgical recovery. The philosophy of mill modernization/modification is generally driven by the desire to increase the mill capacity within the limits of the existing mill building. This need is facilitated by using large size flotation equipment and eliminating multiple parallel flotation circuits in order to minimize capital and operating costs. Conventional flotation machine development has paralleled this mill design philosophy. FLOTATION CELL DESIGN Since froth flotation has been the most widely used separation process for over half a century, one would expect that it would be possible to design and select flotation machines for specific applications based on scientific principles. But this has not been the case. Best judgment, experience and personal prejudice have played a key role in equipment selection. These factors, along with the difficulty of evaluating new concepts in commercial plants, has slowed progress in implementation and commercialization of innovative ideas and/or equipment. Conventional Flotation There have been no major technological advances in conventional flotation cell design in recent years. A recent flotation cell survey indicates that 'larger flotation cells are still the order of the day.”(1) A comprehensive review of design of flotation machines indicate that they have been mechanically redesigned and are generally simpler and easier to maintain and less expensive to manufacture. (2,3) The approximate chronological development of conventional cells from the 25 cubic foot cells to the 3000 cubic foot cells, which were recently installed at the Copperton concentrator of Utah Copper, is given in Table 1. Larger flotation cells are the obvious choice for new plants or plants looking for expansion because of the following reasons: • They have lower capital cost per unit volume • Installation costs are generally lower because fewer units require less space • Maintenance costs are lower because of fewer mechanisms • Power requirements (HP/ton dry feed) are generally lower • with increased flotation cell size as illustrated in Table 2 [Table 1. Conventional Flotation Cell Size Development Year Individual Cubic Cell Size, Feet 1925 25 1935 50 1960 100 1965 300 1970 500 1975 1,000 1980 1,500 1985 3,000]

Jan 1, 1989

By Max Friedemann, Franziska Günther, Helmut Mischo

Ensuring adequate ventilation is a critical aspect of safety in underground mining operations. In small-scale mines in particular, key ventilation parameters such as temperature, humidity, and air velocity are often measured manually and only at infrequent intervals, typically using analog instruments. As a result, real-time monitoring of environmental changes, timely detection of hazardous situations, and demand-driven ventilation control are not feasible. This presentation discusses the selection and evaluation of modern digital ventilation measurement devices, including handheld instruments with digital data logging capabilities and continuously operating sensors with potential for real-time data transmission. The investigations focus on the challenges posed by underground environments with extremely high humidity levels, which can adversely affect sensor performance and electronic components. The results are based on testing conducted at the Research and Teaching Mine of TU Bergakademie Freiberg—an underground ore mine characterized by humidity levels exceeding 95%. Findings include assessments of measurement accuracy, reliability, and practical applicability under these demanding conditions.

Feb 22, 2026

By Matteo Cortinovis, Giuseppe Gelmi

"INTRODUCTIONEdilmac dei F.lli Maccabelli (hereinafter referred to as Edilmac) has recently developed a special civil engineering application using the Raise Boring technology with the assistance of Inrock MGS (Magnetic Guidance System). Applying the Paratrack Magnetic Guidance System coupled with a directional mud motor to the drill string allows a better accuracy compared to standard drilling, as showed in our tests. This is the first time the Paratrack System has been applied to the Raise Boring technology. RAISE BORING METHOD STATEMENT The Raise Boring technology was born in North America during the Sixties. In 1962, Ingersoll and Robbins were the first companies to produce Raise Boring Machines (RBM). The technology was first used in the underground mine industry, in order to bore ventilation shafts and passes through different levels, thus reducing the cost of haulage. The Raise Boring method is only feasible in stable rock conditions. The Raise Boring method consists of drilling a small diameter pilot hole that reaches a tunnel located at the bottom of the drilled hole. Once the pilot hole reaches the tunnel, a reamer head is installed at the end of the drill string and pulled up, creating the hole with the designed diameter (Figures 1 and 2). The main equipment, which is required to perform Raise Boring activities, is the following: •,An RBM; •,A tricone bit; •,Drilling rods; •,A reaming head; The standard mucking of the pilot hole is done with water or bentonite mud. For the last 30 years, Edilmac has developed a mucking process, which uses compressed air with the addition of foam or a small amount of water for dust control.Pilot hole tricone. The drilling of the pilot hole is usually performed with a tricone bit having a diameter between 11” (27.61 cm) and 15” (38.10 cm) (Figure 3). High strength rods. They generally have a diameter ranging from 10” (25.40 cm) to 12 ?” (32.70 cm) (Figure 4), depending on the length and the final diameter of the shaft."

Jan 1, 2016

By J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870's with rising national wealth and declined in the 1950's when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By Kathleen A. Altman

INTRODUCTION The basic premise of the ideas presented in this paper are as follows: Engineers believe that "theoretically" it will work. Operators ask what they must do to make it work. And, people can screw it up. r Today the challenges conf onted during the engineering, startup and operation of mines are becoming more complex. As mining and processing professionals, we are called upon to trav­el all over the world, are subjected to a wide variety of climates and must deal with a numerous cultures and people. Historically, for the majority of the people working in the mining industry, the primary challenges related to projects have focused on the differing perspectives of the disciplines involved. For example, geologists focus on resources and reserves, mining engineers relate to tons or tonnes, metallurgists count ounces or pounds or kilograms of product, mechanics emphasize availabil­ity, human resources personnel deal with absentee rates and turnover and accountants watch the bottom line ($$'s). As the world has become "smaller" and the mining industry has become more globalized, the puzzle is becoming increasingly difficult. Even the most experienced in the crowd of mining profes­sionals are oftentimes surprised by the types of problems that are encountered. Try as we may, we cannot anticipate the complex­ity of dealing with the human side of an operation.

Jan 1, 1998

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

Preliminary design is underway for a new Southern Nevada Water Authority (SNWA) project that will ensure one of America’s most reliable water systems by providing continued, reliable water service to existing and future customers. The Horizon Lateral is a $1.6 billion water transmission pipeline that includes 7–10 miles of 108-inch finished diameter rock and soft-ground tunnels. The tunnels will traverse volcanic rock in or around the McCullough Mountain Range and the surrounding alluvial basin. The tunneling community will find relevance in hearing about this critical infrastructure project from a leading wholesale water utility owner with a proven track record for on-time, collaborative projects.

Dec 1, 2022

By Clayton Williams, Dale M. Hata, Glenn M. Boyce

The Upper Llagas Creek Flood Protection Project in Northern California encompasses portions of the communities of Morgan Hill and Gilroy, and unincorporated areas of Santa Clara County. The project provides for flood protection improvements along Llagas Creek and two of its tributaries, West Little Llagas Creek and East Little Llagas Creek. Llagas Creek is one of the tributaries of the Pajaro River and drains a watershed of approximately 104 square miles. The river system has a history of flooding the watershed communities, and the project’s goal is to provide 100-year flood protection by creating a bypass infrastructure, including channels, cut-and-cover culverts, and a tunnel. The project has been divided into several phases. This paper describes Phase 2A, which consists of approximately 2,150 linear feet of lined horseshoe-shaped bypass tunnel measuring 14 feet wide by 12 feet high. The bypass tunnel was sequentially excavated using a combination of roadheader and controlled blasting through colluvium and weathered to fresh greenstone. The tunnel was mined near residences, requiring strict noise and vibration controls. Phase 2A also includes the construction of twin bypass concrete culverts, portal shoring, and dewatering systems. It features the use of a Design Review Board and partnering for project delivery. This case study discusses the bypass tunnel design, progress of tunnel construction, plans to complete the work, construction risks, and the software and procedural tools being used to manage the project, including ProjectWise construction management software.

Jun 13, 2023

By T. Acton

The Zarafshan/Newmont Joint Venture is currently operating in the Republic of Uzbekistan producing in excess of 400,000 oz. of gold per year from low grade oxide ore stockpiles adjacent to the Muruntau open pit gold mine located in the Kyzylkum desert of central Uzbekistan. Four stage crushing and screening produces a final product for heap leaching, Merrill-Crowe processing, and local refining for International market export. The Zarafshan/Newmont Joint Venture is the first major commercial project of its kind in the former Soviet Union to be successfully negotiated, engineered & constructed, and placed into continuous operation,

Jan 1, 1997

By J. Gauntt

Calcium carbonate is one of the most widely used industrial minerals in applications like cement, lime, agriculture, power plant fluegas desulfurization (FGD) and construction aggregates. Most applications are generally high-volume and low value ($9/t or $10/st) or less free-on-board (f.o.b.) mine site) uses of this material. Specialty uses of ground calcium carbonate (GCC) are typically referred to as ?performance mineral? or ?extender and ?ller? applications. Primary specialty markets for GCC include paper and plastics as well as a number of construction applications including joint compounds, carpet backing, paint, and adhesives, caulks and sealants (ACS). Other important specialty applications for GCC include rubber, food and personal care products. A new and growing application for GCC is in nonwoven fabrics, where this mineral replaces a small percentage of the polymer. Typical specialty applications for GCC are color sensitive and require extremely white/bright materials. Although deposits of limestone are located in most states, high brightness resources are relatively rare and controlled by a limited group of suppliers.

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

Jan 1, 2005

By F. X. Meagher

Vertical slot raise driving from bottom up has always been a hazardous, inefficient, high cost operation. The introduction of the Simba 5 drill rig has enabled this type of raise to be drilled accurately from the top down and to be blasted in stages from the bottom up. Safety, high efficiency and low cost were the main criteria in opting for this method. Drop raises with the Simba 5 at Geco have been successfully drilled and blasted up to 115 feet, and this is close to the maximum length of raise that can be drilled and blasted efficiently with Simba 5. A look into the future would indicate a rig capable of drilling up to 200 foot raises with the same accuracy of Simba 5 to 115 feet.

Jan 1, 1974

By J. A. Wallace

U. S. Steel's coal mining research activities are directed toward providing new or improved hardware and techniques to increase productivity or reduce cost. Because more than 80 percent of U. S. Steel's coal production is obtained from continuous miner sections, most of our research efforts are focused upon that mining system. Current and historical time study data show that our continuous miners only operate about 30 percent of the available face time. This limited equipment utilization is the result of the delays or interferences imposed by the non-coal-cutting phases of the continuous mining cycle. The most time consuming of these delays are: waiting-on-roof-support, tramming between alternate work locations, waiting-on-haulage-capacity, and in some mines waiting for excessive methane concentrations to clear. Because waiting on roof support is our most time consuming delay, several programs are underway simultaneously to address this problem. In one of these we are developing a patented microprocessor-based control method and apparatus to improve roof drilling performance. This increase is attained by using the microprocessor to adjust electrohydraulic valves which control drill thrust and rotation speed. The microprocessor is designed to continuously search for an optimum combination of thrust and drill rpm to maximize penetration rate at all times.

Jan 1, 1979