Search Documents

By Siqing Liu

A low-grade cassiterite-magnetite ore from Sichuan province, China, is finely disseminated, assaying 0.39% Sn and 23.20% Fe, respectively. Mineralogy studies show that the fine-sized cassiterite is mainly disseminated in iron minerals and gangue. Moreover, the embedded size of cassiterite is very fine and must be ground to -0.01 mm to achieve a degree of liberation of about 90%. Therefore, fine grinding needs to be conducted to get a high quality tin concentrate and a great loss of tin cannot be avoided when treating the ore by gravity concentration. Based on the above facts, a two-stage separation, with a low intensity magnetic separator and a shaking table, was selected to test the ore. Compared with other similar plants, a relatively good separation has been achieved. Three acceptable products for smelters were obtained as following: iron concentrate assaying 61.69% Fe with a recovery of 75.09%, tin concentrate assaying 27.21% Sn with a recovery of 56.97% and a sulfur concentrate assaying 40.86% S with a recovery of 32.03%, respectively.

Jan 1, 2011

By Howard M. Cotton

Early in 1977, Amoco Production Company and Houston Chemicals, a subsidiary of Pittsburg Plate Glass (PPG) Industries, started producing iodine commercially in northwestern Oklahoma. This is significant because it is the first plant in over 40 years to be built in the United States with iodine as its sole commercial product. With the exception of a limited amount of iodine produced by Dow Chemical in Michigan, the United States is dependent upon imports from Chile and Japan for its iodine needs. The two million pounds of iodine produced annually from the Woodward plant will supply over one-third of the United States' requirements. Routine analysis of subsurface brines by the Formation Water Lab at the Amoco Production Company Research Center in Tulsa, Oklahoma, revealed unusually high concentrations of certain potentially economic minerals. Investigations determined that, of the minerals in question, iodine appeared to offer the best potential. The brines in question are located in the Morrow sands (basal Pennsylvanian) at a depth of 7,175 to 7.400 feet, in an area where Amoco has been active in a gas play for the past 20 years. The regional iodine concentration ranges from 10 to 700 ppm and averages around 300 ppm with the project area. The project is located 8 miles north and slightly east of the town of Woodward, where the well-developed, porous, and permeable sands of the Woodward trench contain large volumes of brine.

Jan 1, 1978

By Stephen Benyo

The future of mining will not be defined by how deep operators dig, but by how intelligently they separate. As ore grades decline, environmental concerns intensify and water remains a global crisis, the industry is discovering that its greatest opportunities for progress lie not at the pit or face, but downstream — within the separation processes that govern water, tailings and byproduct streams. In this context, clarity has become a defining principle — both literally and metaphorically. Clear process water enables reuse and regulatory compliance. Clear separation of solids and liquids recovers valuable resources, supports safer operations, lowers energy demand and provides stable tailings management. Clear visibility into how these systems perform allows mine operators to make better decisions, reduce operational risk and unlock value that is often hidden in overlooked waste streams.

Apr 1, 2026

By Russell L. Wood

The title of this session seems to have been picked especially for this paper. It is 1984, it is the morning after, and there is one monumental hangover among many if not most of the oil companies that have invested in mining in the past decade or so. How an oil company looks at mining depends on what time period you are talking about. A few years back around the time of investment this is what they were probably looking at: 1. A balance sheet of their own that was beginning to go wild, with many of their commodity prices having already seen increases of two, three, or four fold, and with no end in sight. 2. A need to invest their earnings someplace fast before the stockholders or the government got too interested. And that someplace should be in an industry where their own management skills could be applied. (Only a true cynic would suggest that this is a form of job security) 3. In mining there was an industry amazingly similiar to their own, one working with non-renewable natural resources, dealing with the same types of government agencies, and having the same type of critics and pressures from the general population. 4. An industry that was somewhat backward as compared with their own, and one where a generous ration of the capital and management skills so handsomely bestowed upon the oil industry could be used to great advantage.

Jan 1, 1984

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By J. Trouw, W. de Bruijn, A. van Sandwijk, R. H. Heerema

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically prepared hematite powder evenly doped with 1 % by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous theimogravimetric and dilatometric analyses were performed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process. The results indicate that the degree of expansion or shrinkage of hematite during reduction is highly dependent upon impurities associated with the original material; marked differences in reduction rate and microstructure were observed as well. An important finding is that the influence of a particular additive can also strongly vary from one reduction stage to the next. The reduction behavior appears to be affected by the physical and chemical nature of the associations formed by the added elements.

Jan 1, 1990

By Charles G. Zink

Early anthracite "deep mining" methods, production, manpower. underground transportation, labor, safety and reserves are reviewed and compared to the present and to future requirements which must be met in order to economically win the fourteen million tons of untapped reserves and to keep the product competitive in the market place.

Jan 1, 1971

By Lourens Scheepers

Mining induced seismicity and rockbursts have been part of the deep level gold mining industry in South Africa for many years. One could be forgiven for thinking that we should know everything there is to know by now to have rockbursting under control to a level that it has minimal impact on safety and production. Well, we don’t… There are things we know that we know, and they are implemented, or should be. There are thigs we know that we don’t know, and they are researched, or should be. There are things we don’t know that we don’t know, and, well, we don’t know… We know that seismicity and the associated potential for rockbursts generally increase with an increase in stress (increase in mining depth and/or mining span and creation of remnants) and proximity to faults and dykes. We know there are a number of potential sources of events in a mine; that is: mining abutments, pillar abutments, mining faces and geological structures (faults and dykes). We know there are a number of event mechanisms associated with these sources; that is: slip on a geological structure, shear through intact rock and bursting of the rock near the edge of a mining excavation. One of the tools used more and more and with increased success to identify event source mechanisms is Moment-Tensor analysis (MT). This typically assist in differentiating between three event mechanism components: volumetric deformation component, axial deformation component and slip / shear component. The insight gained from MT assist greatly in identifying the most likely event source to assist in understanding the rockmass response to mining. We know that the seismic response in our mines are mining induced (not natural). This may seem trivial, but it is important to realise that we influence the seismic response with the way we mine, and by how much we mine (extraction ratio). Therefore we put design rules and strategies in place to reduce the seismic hazard and we install rockburst support in our mining excavations. We know the seismic response to mining is influenced by the properties of the rockmass, including strength, stiffness and brittleness, but quantifying its influence is typically more difficult than expected. We know numerical modelling can improve the engineer’s understanding of the potential rockmass response associated with designed mining layouts and strategies. For our environment (narrow, tabular large area) elastic boundary element modelling remains the most convenient and practical approach, but it overestimates the stress at mining abutments and underestimates the stress further away from these abutments. Adding a crushing (based in limit equilibrium) modelling approach vastly improves the boundary element modelling ability to simulate the deformed (interpret fractured) zones and associated redistribution of stress. We don’t know how to quantify what an acceptable seismic risk is. We don’t know if we can mine remnants at an acceptable seismic risk. Some remnants are extracted surprisingly easy, others serve us with devastating rockbursts. The limit equilibrium modelling shows potential to significantly improve our ability to quantify the rockburst risk. We don’t know if large-scale preconditioning is possible and will be effective to significantly reduce the seismic risk associated with remnant and pillar mining. Research is required (and has been initiated). Vast areas of ground have been extracted historically in the South African gold fields. Most gold reserves are now in deeper ground (4000 m) and historic remnants (areas left before due to mining difficulties) as well as pillars (regional stability pillars). If we cannot find ways to extract these reserves at acceptable risk levels, the future of the South African gold mining industry is very short.

Apr 26, 2022

By Kenneth S. Johnson

Oklahoma is the only; state in the nation that is currently producing iodine. The iodine is extracted from iodine-rich natural brines being pumped from deep wells drilled into Pennsylvanian sandstones in the Anadarko basin of northwestern Oklahoma. Woodward Iodine Corp., started in 1977, was the first plant in the United States built for iodine recovery since the 1930s. At present, three companies are operating four iodine-producing facilities in northwestern Oklahoma. The combined production of these facilities, 1,321,000 kg in 1997, is about 26% of the U.S. annual consumption. Iodine is present in concentrations ranging from less than 100 ppm (parts per million) to as much as 1,560 ppm in brines in various Paleozoic strata in the subsurface of northwestern Oklahoma; these concentrations are exceptionally high, and are well above those of any other known brines in the world. Strata with the highest iodine content in the area (Mississippian limestones) have low permeabilities, and thus would yield only small amounts of brine. On the other hand, the lower Morrow sandstones (Lower Pennsylvanian) have a relatively high permeability and are capable of yielding large quantities of brine that average 300-350 ppm iodine. The Morrow brine reservoir was deposited in shallow-water-marine and intertidal-shelf environments and now is buried 6,000-10,000 ft below the land surface. Production is localized to Morrow channel deposits confined to an Early Pennsylvanian paleovalley that is 1-2 mi wide, is about 70 mi long, and is referred to informally as the "Woodward trench." All three companies are producing iodine-rich brines from Morrow sandstones in three different parts of the Woodward paleovalley, and one of the companies also is extracting iodine from oil-field brines coming from several petroleum reservoirs near Dover, about 80 mi east of Woodward. The basic extraction method employed by Woodward Iodine Corp. was used in Louisiana and California operations in the late 1920s. This method is commonly called the air-stripping process. Lower Morrow brine containing dissolved sodium iodide is pumped to the plant through a series of pipelines, where by-product natural gas is separated and processed. The brine is then acidified and subsequently oxidized with chlorine to convert the iodide to iodine. The iodine is air stripped and reabsorbed with sulfur dioxide and water, converting it to hydriodic acid, or process liquor. The process liquor is then processed, using chlorine once again, to crystallize the iodine as a solid. This is then melted and frozen to form a solid product, which is packaged in 110-lb (50-kg) drums and shipped to end users throughout the world.

Jan 1, 1999

By R. Costa, A. Kozak, B. Fukuhara

Introduction The Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc. The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain. The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mined has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. and now Yamana Gold Inc.

Jan 1, 2007

By Chee S. Theng

As the 2016 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2016 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 340. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2016 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-issue articles on process development testing. The 2016 Transactions consists of a total of 65 technical papers, encompassing all 21 papers published in 2016 in the Technical Papers Section of Mining Engineering (Vol. 68) and all 27 papers published in 2016 in Minerals & Metallurgical Processing (Vol. 33). Additionally, this volume contains 17 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2016 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2016

By T. McCallum, B. Wellbrook, T. Ratnaweera

"Pressure oxidation (POX) leaching of copper (Cu) concentrates continues to be explored as the next generation of leaching processes to sustain existing Cu Solvent Extraction/Electrowinning (SX/EW) operations as easily leachable ores become scarcer. The leach liquors produced, particularly from total pressure oxidation, contain elevated concentrations of Cu and acid, making solvent extraction processing more challenging. Addressing this challenge will require innovative processing techniques and continuous improvement to be successful in achieving satisfactory physical and metallurgical performance in the SX plant. The ability to efficiently process these feeds via SX plays an important role in the continued success of POX technology. Characteristics of a concentrate leach pregnant leach solution (PLS) are discussed, along with best practices that should be considered for processing by SX. Findings discussed in this paper will shed light on ways to reduce process risk and bring additional improvement to the industry with minimal change to the SX plant. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electro refining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges. The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile. The experience related to the current paper centers around Cu concentrate leaching performed by Freeport McMoRan (known as CLP). The patented process was developed as an alternative to smelting and refining in 1998. The technology applies to both molybdenum and copper concentrates. Commercial CLP research and development began with Phelps Dodge in 1999 to 2001. The first commercial plant was commissioned in 2003 at the Bagdad operation. Initial operating conditions of the Bagdad CLP were under high temperature conditions before converting in 2005 to medium temperature conditions. In 2007-2009, the CLP technology was commissioned in Morenci, operating medium temperature and high temperature lite conditions until shutting down due to the economic downturn. The Morenci CLP restarted operation in April 2015 due to acid production benefits for the Morenci leach operations. Renewed solvent extraction test work initiated well before restart and has been an ongoing focus for further SX plant optimization."

Jan 1, 2018

By S. Tavani, R. E. Browner, R. Dunne

Lead is used in CIP/CIL circuit to increase the leaching rate of gold from ores. At least four mechanisms have been proposed for the action of lead in gold leaching circuits: (I) precipitation of sulphides as highly insoluble lead sulphides preventing consumption of cyanide and oxygen; (2) su,face reaction on sulphide particles forming an insoluble lead sulphide layer peventing dissolution of those sulphides; ( 3) precipitation of lead sulphide, which undergoes further oxidation to soluble lead sulphate recycling the lead to solution,· ( 4) contact reduction of lead onto the gold szaface which then acts as a secondary oxidising agent. Rotating disc studies using a pure gold disc show that small amounts (5ppm) of sulphide ions are sufficient to significantly reduce the leaching rate of gold. Lead increased the leaching rate at small concentrations but at higher levels decreased the rate of leaching. The detrimental effects of lead were only found for a pure solution when leaching the gold disc. Ores mediate the amount of lead available by ads01ption/reaction, thus, reduced leaching rates from excess lead are not serious even when 500ppm of lead ions are added to the sluny. The detrimental effects of sulphide ions could be countered by lead addition during the leaching process. A penalty, in the form of reduced leaching rate, will occur the longer lead addition is delayed. A time lag was noted between the addition of lead and the increased leaching rate when a large concentration of sulphide ions was present.

Jan 1, 2000

By Evan J. Owen, Virginia T. McLemore

The Zuni Mountains, located in Cibola County, New Mexico is an uplifted area that exposes Proterozoic igneous and metamorphic rocks overlain by Permian and younger sediments. Sedimentary-hosted Cu deposits and fluorite veins in the district have recorded production, but other deposits exist. Proterozoic ultramafic rocks may host Ni and PGE. A recent regional stream sediment survey collected 76 samples as part of an exploration geochemistry course at New Mexico Tech with the goal of assessing the critical minerals potential of the district. Whole rock and trace element chemistry of the sediment samples (<2 mm) show a variety of critical minerals possibly worthy of future targeted exploration including up to 700 ppm As, 2100 ppm Ba, 26 ppm Bi, 25 ppm Co, 640 ppm Cu, 145 ppm Ni, 110 ppm Sb, 170 ppm V, and 500 ppm Zr. Positive correlation between Bi, As, Cu, and Sb suggest that these critical minerals are found together within copper veins related to shear zones in the district. Samples collected from streams that drained outcrop of mafic and ultramafic rocks were found to generally contain more Ni, Co, and V. Samples elevated in Ni will be reanalyzed for PGE.

Feb 1, 2025

By L. G. Stolarczyk

In-mine Continuous Wave (CH) Radio Imaging method (RIM) instrumentation has the capability of measuring EM wave propagation constants in layered formations. The RIM method is based upon the fact that seams of coal, trona, potash, quartzite, gilsonite and oil bearing sands form natural waveguides for low loss transmission of electromagnetic (EM) waves. The waveguide forms whenever the seam is bounded by more conducting claystone, mudstone, shale or in the case of oil/gas traps, by a floor of saline water. Disturbances caused by faults, shear zones, paleochannels, sills and dikes significantly alter the propagation constant. The analytical values of the EM wave propagation constants depend on the physical and electrical parameters of the seam. The values are presented in this paper in a graphical form to assist in the interpretation of RIM tomographic images. This paper compares in-mine geologic mapping obtained during mining to tomographic images of the geologic disturbance zones in a Central Utah coal mine.

Jan 1, 1989

By Kate Willa Brown Requist, Eric Lutz, Moe Momayez

As air quality sensor networks become increasingly popular in underground coal mines, it is important to generate paradigms for the application of the collected data. To date, air quality sensing has been primarily used as an early warning system for hazardous air conditions. Using data collected from a network of sensors in a US underground coal mine, we have created multiple visualization methods to show the interactions of carbon monoxide evolution with ventilation airflow. These visualization methods can allow for further analysis of the source of contaminant, as well as better data resolution across the area of concern within the mine. By utilizing univariate spatial interpolations, we present methods for identifying the movement of carbon monoxide at one-minute intervals. The resulting visualizations display the evolution of carbon monoxide concentration across a sizeable study area over a period of 14 minutes.

Jun 25, 2023

By D. C. Seidel, W. K. Tolley

Supercritical water alters the structure of common sulfide minerals by partially removing sulfur from the mineral structure. This discovery has been applied to the treatment of pyritic gold ores to improve precious metal recovery without generating or utilizing environmentally sensitive products such as S02, chlorine, or cyanide. Pretreating pyrite concentrates in supercritical water under mildly oxidizing conditions provided by certain metal oxides or oxygen improved gold leaching using thiourea. The pretreatment differs from chlorination or roast pretreatments in that elemental sulfur rather than sulfuric acid is the major product. A pyritic ore containing 58 g/mt Au was pretreated with oxygenated supercritical water at 24 MPa and 400°C, then leached with 20 g/L thiourea. With pretreatment, gold recovery was 90%; by contrast, gold recovery was below 10% without pretreatment.

Jan 1, 1990

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By Chee S. Theng

As the 2018 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2018 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 344. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2018 Transactions consists of a total of 59 technical papers, encompassing all 25 papers published in 2018 in the Technical Papers Section of Mining Engineering (Vol. 70) and all 26 papers published in 2018 in Minerals & Metallurgical Processing (Vol. 35). Additionally, this volume contains 8 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2018 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume. The new year brings an exciting change. The publication of Transactions will cease with this volume. Instead, our Minerals & Metallurgical Processing journal has the new name of Mining, Metallurgy & Exploration (MME), and Transactions as well as the Technical Papers Section of Mining Engineering are incorporated into MME. The journal is published in partnership with Springer Nature, and all SME members have free electronic access to the journal.

Jan 1, 2018

By R. J. Nankee

Recent on-going efforts to develop commercial coal cleaning beneficiation processes using chlorinated solvents-as the separating media will be described. True heavy media separations were performed on raw coal feedstocks, including Pennsylvania anthracite; Western, Eastern, and Midwestern bituminous; and lignite coals. Separation techniques included bath-type devices, cyclones, and liquid/liquid partitioning. Details on separation devices, removal of solvent, and recovery and recycling of solvent will be discussed. Projected costs of full-scale plants will be given for various coal sizes. A number of the coals evaluated are good candidates for beneficiation using chlorinated solvents. Coal beneficiation is desirable to provide needed coal quality. These needs include low ash fuels for coal water slurries and low sulfur fuels to meet emission regulations. In October of 1985, a paper, "Chlorinated Solvents for Coal Beneficiating"&apos; was presented at the fall meeting of SME-AIME at Albuquerque, New Mexico. It reported the results obtained from various coals as feedstocks and of the separations using chlorinated solvents. These beneficiation results depended on true heavy media gravity and liquid/liquid partitioning separations. This paper will include detailed descriptions of the liquid/liquid partitioning process used in "Dow&apos;s Advanced Coal Cleaning Technology?2 and of the "Dow Solvent Recovery Technology.?3

Jan 1, 1987