Search Documents

By W. J. Fotheringham

This paper deals with the mining techniques employed at Canada Tungsten's northern Canadian operations, particularly with respect to their effect on productivity, safety, and stability of relatively large underground openings. The ore body was originally mined commencing in 1974 using conventional pneumatic jumbos in a topslice and horizontal benching room and pillar layout. Pillar stability became an increasing problem as mining progressed, leading to a re-examination and ultimately a conversion of mining method. Rock mechanics considerations and the effect of extraction rate on ground control costs and conditions are analyzed. Other areas discussed concern the results acheived through the use of large diameter I.T.H. drills, radio remote controlled L.H.D. units, and a unique system of hydraulic backfill placement.

Jan 1, 1985

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By K. Chief

American Indian lands contain a vast amount of renewable and non-renewable resources that have consequently been mined (Smith and Frehner). Therefore, it is understandable that tribes are concerned about environmental impacts from mining and their ability to minimize and mitigate these impacts. This has created a need to better understand mining and its environmental impacts. The University of Arizona Superfund Research Program Mining educational modules developed educational modules for tribal colleges focusing on environmental impacts of mining, remediation of mining wastes, and sociocultural impacts of mining. Educational modules are independently packaged units of study designed to enhance the learning process and can be modified and adapted to different learning scenarios and objectives. In addition to providing specialized knowledge, the modules feature hands-on activities, incorporation of technology, student involvement, discussion, and exchange of ideas. Modules will aim incorporate traditional ecological knowledge and approaches that promote effective science learning for native students. Modules are designed to augment existing associates of science programs (e.g. biology, chemistry) currently offered at tribal colleges and can be modified for use in K-12 education and for non-tribal audiences.

Feb 23, 2014

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998

By Randall C. Divito, Craig R. Eckdahl, Bruce D. Wagener, Joseph Klejwa

The existing Central City Tunnel was built primarily in the 1930s with a small portion as old as the 1880s. It conveys stormwater in downtown Minneapolis. It is a 4,400-ft long tunnel located 80 feet underground. The Central City Tunnel has experienced surcharging and surface overflows during heavy rainfall events. This paper presents the details of tunnel and shaft design for the new Central City Parallel Tunnel to mitigate the overflows. The design considered hydraulics and geotechnical engineering for the structural geologic conditions including the weak Saint Peter Sandstone and overlying strong Platteville Limestone. Ground conditions resulted in tunnel designs including large flat-back box tunnels and unique cathedral-shaped tunnel sections.

Jun 13, 2023

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By R. L. Grayson, S. B. Bealko, L. L. Chasko, D. W. Alexander

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies, including a fire or explosion, a massive roof collapse, mine inundations or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training.

Jan 1, 2010

By M. T. Smith

In a 2,000 square mile area of Polk, Hillsborough, Hardee and Manatee Counties in Central Florida is located one of the richest known deposits of the life-giving mineral, phosphorus. Under layers of sand and clay are found millions of tons of phosphate rock, best source of this element which is necessary to all forms of life - plant, animal and human. Phosphorus is an irreplaceable ingredient in all complete plant foods, and more than 90% of Florida's vast production goes to enrich the croplands of the United States and many other areas of a hungry world. In addition to this, it has wide industrial use in the manufacture of many products - detergents, baking powder, carbonated beverages, steel, matches, munitions, glass, insecticides, dyes, water softeners and innumerable others. Not only does phosphorus make life possible for us - it also helps us to live longer and better.

Jan 1, 1962

By R. Mattos, E. Calcina, G. Quispe, S. S. Kanchibotla

During blasting, rock breaks and moves but standard grade control practices do not adjust ore waste boundaries to cater for blast movement. Rock movement resulting from blasts can result in mischaracterization of grade boundaries resulting in ore loss and dilution. Ore loss takes place when ore is mischaracterized as waste and sent to waste dumps, and dilution occurs when waste is mischaracterized as ore and sent for processing. Las Bambas operations of MMG Peru, realized the economic impact of blast movement on ore loss and dilution and adjust ore boundaries using limited blast movement measurements. This is a step in the right direction but has limitations for everyday application. This paper discusses the advantages of disadvantages of current blast monitoring techniques and introduces an operational tool to estimate polygon movements for different blast designs and confinement conditions. Blast movement estimates from this new tool have been compared against the estimates from the current tools for several production blasts and the results were quite promising.

Mar 2, 2022

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By Ingo Kaundinya

"INTRODUCTION Tunnels are important elements of the German federal road network which have to cope with an increasing traffic load especially of heavy goods vehicles. In order to ensure a high availability and safety level for these key infrastructures, big efforts are required by owners and operators in order to keep all infrastructures up to date. This mainly relates to current European regulations regarding tunnel safety (Directive 2004/54/EG) [1] and their national implementation, which must be fulfilled by many existing tunnels. In this context the German Federal Government spends more than 1.1 billion € for the structural and operational retrofitting of more than 120 existing road tunnels. As many of these projects have recently been finished or are still under progress, experiences and best practices could be reported. After the description of current requirements in national standards regarding structural fire protection, the paper gives an example for an upgrade of a tunnel’s fire protection by installing an additional fire protection system, which is a quite costly measure. Another possibility to fulfill current requirements regarding structural fire protection could be the numerical proof of sufficient bearing capacity of a structure. The influence of different fire loads and fire durations on the bearing capacity of typical road tunnel structures have been investigated in a research project funded by the German Federal Ministry of Transport (BMVI) and coordinated by the Federal Highway Research Institute (BASt). The results of this research project have been used to define a procedure how to investigate existing tunnels regarding structural fire protection. Finally, the research results have also been the basis for a current update of national standards for tunnel construction. REQUIREMENTS REGARDING STRUCTURAL FIRE PROTECTION The structural fire protection design of road tunnels is usually based on temperature-time curves of exposure to fire, for simplicity called ""fire curves"". The fire development after fire growth is illustrated with fire curves. Fire curves can be subdivided into a heating-up phase, a fully developed fire phase, and if applicable, into a cooling-off phase (cf. Figure 1). During the fully developed fire, the fire remains at a certain temperature level."

Jan 1, 2016

By A. J. Teske

Sustainable Development is a very broad initiative in the mining industry, with major components running over the entire life of the mine. It likely commences with pre-exploration permitting and continues to post-mining final closure and possible land reuse. Most major mining corporations embrace the sustainability initiative, either out of a sense of social responsibility or out of necessity in order to continue doing business. But many may view the overall initiative as an added ?cost of doing business.? In many elements of sustainability, there clearly can be added cost ? some as simple as complying with self-imposed sustainability reporting. Fortunately, one major element of sustainable development can clearly be shown to reduce costs ? energy resource management. This paper will describe how the mining industry sustainable development effort differs from other industries, but can benefit from their experience in energy resource management. The mining industry can utilize proven methods from other industries to further their energy management efforts. In addition, many of the resources developed and employed to promote better energy resource management in non-mining industrial settings will be listed.

Jan 1, 2010

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By Hongjie Yu, Rakshith Shetty, Claudio Cimiotti, Nick Karlin, Mike Mooney, Vitaly Proshchenko, Matt Kendall

This paper documents an effort to explain cutterhead torque behavior observed during slurry pressure balance TBM tunneling through soft ground on the Los Angeles Clearwater project. AI machine learning and mechanics model-based learning was used to characterize cutterhead torque behavior including the TBM operating and ground parameters that influence cutterhead torque. Also, key parameters were from the slurry circuit data, including fines content, in-situ density, pore water fraction and solids content were included. The paper details what was learned using these new data-driven approaches as well as limitations with AI machine learning.

Jun 23, 2024

By C. Patrick

Annually, the U.S. coal industry generates and must dispose of over 200 million tons of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks, used for under-ground ventilation stoppings, with refuse blocks. Refuse was collected from three active preparation plants in Eastern Kentucky and used as the primary aggregate for concrete cylinders. The refuse fell within ranges normally observed for size consist, moisture, and ash. Stress-strain analyses yielded compressive strengths of the refuse cylinders from 59% to 77% of the control group strengths. Low variability within groups while significant differences between groups were found. On-going determination of effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1995

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By Donn W. Leva

In North America, pipelines move more material than any other form of transportation. 1 Pipelines have been used principally for the transportation of liquids and gases; however, slurry pipelines have made notable gains in recent years enabling solid materials to be moved efficiently by pipelines. The obvious advantages of pipe-lines --low maintenance, low operating costs, minimal impact on the environment, greater land use, low labor intensity, safety and high operating factor --have stimulated researchers in England, West Germany, Japan, USSR and the USA during the past ten years to develop pneumatic capsule pipelines for the movement of bulk materials in large quantities. As a result of this work, pneumatic capsule pipelines are now available for the movement of dense bulk materials. Through these pneumatic capsule pipelines, material is moved in wheeled capsules which are pushed through the pipeline by flowing air. In this paper, a capsule pipeline system developed by the Georgia Institute of Technology and Tubexpress Systems, Inc. of Houston, Texas is discussed. The Tubexpress System Major Components The pipe used for a Tubexpress capsule system is standard thin wall welded steel pipe. Since pressures in the system generally do not exceed one atmosphere, the controlling design criteria for wall thickness of the pipeline is pressure from the overburden of the backfill if the line is buried or the structural requirements for supporting itself and the load if it is suspended or supported on piers. The air pumping system for Tubexpress is a combination of

Jan 1, 1977