Search Documents

In phosphate flotation, more than 90% of the finer fraction (-35, + 150 mesh) is recovered as opposed to 70% of the coarser material (-16, + 35 mesh). On the other hand, coarser fraction is higher in phosphate content than the finer feed. Consequently, improvement in the coarse recovery is highly desired. It was determined on bench scale that emulsification of the collector (fuel oil and fatty acid mixture) can lead to enhanced recovery of coarse particles. Flotation of phosphate with emulsified collector resulted in improved recovery and grade also on the plant scale.

Jan 1, 1992

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By Nasri Munfah, Steffen Matthei, Vojtech Gall

"Conventional tunneling as defined by ITA WG19 is also known as the New Austrian Tunneling Method (NATM) or Sequential Excavation Method (SEM) was transformed in the US to deal with challenging tunneling conditions as an alternative to the more traditional tunneling methods. It is being used more often in urban areas, under difficult ground and ground water conditions, and with limited cover. Often the tunnel is of a large and non-uniform cross section in soft soils or weak rocks. The intent of using this tunneling method is to minimize impact on traffic and utilities and reduce disruption of everyday life of people and businesses. To meet these challenges, the industry developed technical approaches and implementation techniques and established sophisticated contractual relationships and collaboration in the field among various parties for successful implementation. This paper examines the development of conventional tunneling (NATM/SEM) in the US to deal with these challenges using recent examples such as Russia Wharf in Boston, Northern Boulevard Crossing, in New York, and Chinatown Station in San Francisco. INTRODUCTION / HISTORY Conventional tunneling or NATM/SEM is a concept that is based on the understanding of the behavior of the ground as it reacts to the creation of an underground opening. In its classic form the SEM/NATM attempts to mobilize the self-supporting capability of the ground to an optimum thus achieving economy in ground support. Initially formulated for application in rock tunneling in the early 1960’s, NATM has found application in soft ground in urban tunneling in the late 60’s and has since then enjoyed a broad, international utilization in both rural and urban settings. In the US the NATM/SEM tunneling method has been used successfully to address challenging tunneling conditions in urban areas. A large number of tunnels have been built around the world using a construction approach which was loosely termed NATM. During the years of discussions and the application of NATM a variety of terms have been used for the same construction approach. These terms were primarily aimed at describing the construction approach rather than the region of its reported origin."

Jan 1, 2016

By J. Andrew McGlenn, Brian McInnes, Bruce Downing, Murray Gant

The Second Narrows Water Supply Tunnel crossing beneath Burrard Inlet is an important component of the Greater Vancouver Water District’s plans to increase seismic resilience and meet increasing water demands. The project included the 110-meterdeep (350 ft) South TBM Receival Shaft, one of the deepest shafts to date in the sedimentary rock unit underlying much of Metro Vancouver. The shaft encountered varied sedimentary rock types, including fractured rock, with accompanying high groundwater inflows. This paper discusses the design and construction challenges associated with this shaft and the necessary means to complete the shaft in time for TBM arrival.

Jun 13, 2023

By John V. Beall

The Mining Engineering Handbook is written primarily for persons interested in the economic extraction of minerals. Not everyone referring to this book will be knowledgeable about mining and, therefore, this section is intended to explain to interested persons the scope of mining as well as fulfilling the title of "Mining's Place and Contribution" among the industries of society. 1.1-MINERALS, ROCKS AND ORE In the year 1971, the number of known elements amounted to 104. Fifteen of these have been made only in the laboratory, others may have persisted from the primitive atmosphere, but, by and large, elements originated from magmas or igneous rocks of the outer rocky shell of the earth. Only eight elements constitute 98% by weight of the earth's crust. These are oxygen, 47%; silicon. 28%; aluminum, 8%; iron, 5%; and sodium, magnesium, potassium and calcium, less than 4% each. These common elements and the other less common ones are the building blocks of minerals, of which there are over 2,000 varieties. According to Webster: "A mineral is an inorganic substance occul.ring natura!ly in the earth and having a consistent and distinctive set of physical properties and a composition that can be expressed by a chemical formula. The term is sometimes applied to organic substances, such as coal." Thus, minerals are precise combinations of elements. Rocks, as distinct from minerals, are composed of assemblages of minerals. When minerals are found in sufficient concentration to warrant extraction by mining, the mineralized area is considered an ore deposit. The definition of ore is mineral that can be extracted from the ground at a profit. The economic connotation is implicit in the word ore. Since most of the useful elements compose such a small percentage of the earth's crust, the occurrence of ore deposits as we know them would not have transpired had not geologic processes concentrated the elements (see Sec. 4). 1.2-DEFINITIONS OF MINING TERMS Extensive coverage of the many descriptive terms used in mining may be found in a good mining glossary, such as is available from the Superintendent of Documents (see Sec. 35), but for convenience a number of the more common definitions are given here. Mining may be defined, as by A. B. Cummins, as the act, process or work of extracting minerals or coal from their natural environment and transporting them to the point of processing or use. Mining techniques are applied to extracting metallic minerals, such as ores of gold, copper, lead or zinc; to fuels, such as coal, anthracite, lignite and tar sands; and to nonmetallic minerals, such as lime-

Jan 1, 1973

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

By S. J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins: including the Emma, Anaconda-Original, Syndicate, Badger-State, and Alice-Rainbow veins, each with strike lengths of over 12,000 feet and vertical continuity in excess of 4,500 feet, along with mining widths from 5 to 50 feet, are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district and eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970’s. Open pit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines. Operations in the Berkeley pit were suspended in mid-1982 because of the rejection of high arsenic, copper concentrates at major smelting facilities throughout the world. Bulk mining of porphyry style mineralization in the Continental pit began in January 1980 to supplement copper production while stripping “C” pushback in the Berkeley pit. The Anaconda Smelter closed in September 1980. A molybdenum circuit was added to the Butte Concentrator in 1981 and mining continued in the Continental pit to produce copper and molybdenum concentrates. A blend of Berkeley and Continental ores were processed to dilute penalty metals in the final concentrates marketed to toll smelters. All mining operations ceased mid-1983 when Anaconda closed the Continental pit and offered the property for sale. Montana Resources reopened the Continental pit in June 1986 to produce copper and molybdenum concentrates. Operations were suspended mid-2000, because of exorbitantly high power prices, but resumed in November 2003 with rising metal prices. Bulk open pit mining of the early porphyry style mineralization has sustained production over the past twenty years and mining is expected to continue in the Continental pit with favorable prices. Future mining will eventually develop a 500 million-ton geologic resource incorporated in a supergene enrichment blanket situated between the Berkeley pit and the Continental pit. Grades in this enrichment blanket range in the neighborhood of 0.5% copper.

Jan 1, 2006

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By Wayne Charlie, Joseph P. Martin

INTRODUCTION Typically, uranium mills produce slurred tailings which are transported by pipeline to a tailings impoundment. The slurried tailings contain about 250 solids (75% liquids) by volume and, depending on the milling process, have a high or low ph. Despite decanting water from the tailings pond and losses by evaporation and seepage, Staub (1978) estimates that for lined impoundments over half of the input water is stored in the tailings. As long as the impounded tailings remain in a loose and saturated state, potential hazards exist and include potential for short and long-term seepage from the impoundments and the potential for large scale release and movement of liquified tailings should an embankment fail. The breach of an earthen dam on July 16, 1979 at Church Rock, New Mexico, and the subsequent release of 100 million gallons of water and liquified uranium tailings, underlines the potential hazard. Loose saturated tailings also have a high potential of liquefaction during earthquakes (Charlie and Wardwell, 1979; Martin, Finn and Seed, 1978; and Mittal and Morgenstern, 1976). If the tailings could be dewatered, the liner's integrity would become less critical, longterm seepage and settlements would be greatly reduced. In addition, the potential for tailings liquefaction from an embankment failure or earthquake would be greatly reduced. This paper reviews the concept, criteria, and design of various proposed interior drainage systems to dewater the tailings after deposition. ADVANTAGES OF INTERIOR DRAINAGE The primary purpose of interior drainage systems for uranium mill tailings impoundments is dewatering the tailings as rapidly and as thoroughly as possible. The expected benefits of this new technology are: • Reduction of potential seepage losses by decreasing the hydraulic head. • Reduce earthquake liquefaction potential of the tailings by inducing non-saturated conditions and/or lowering the water pressure. • Reduce the potential for large-scale release and movement of tailings should an embankment fail. • Stabilize the tailings to permit early reclamation. • Recovery and potential recycling of tailings liquid. • Inhibiting long-term seepage out of the impoundment by inducing nonsaturated conditions to provide capillary suction in the tailings.

Jan 1, 1980

By M. Ramokhothoane, S. Rupprecht

"NTRODUCTION Women employment in the mining industry dates back to the 19th century. Various parts of the world, for example, India, Japan, the United Kingdom and the United States of America had women employed in large numbers. The women’s jobs were primarily manual in nature. Women were used to carry coal in buckets from the coal face and out the mine, and those who worked on the surface plants were used to sort waste rock from the coal product. Other heavy industries, which were traditionally male dominated, for example the military, also had a considerable number of women supporting the war effort. The outbreak of war also caused a shortage of labour, which in turn, necessitated that women were used in various roles during the war. After World War II, women returned to their traditional roles, but had acquired new skills, and had a different outlook to life. The wearing of pants and short hair became fashionable, as a result of being in the army.Various laws were passed which prevented the employment of women underground. Different countries had rules that they believed were in the best interest of women and were of the opinion that the rules somehow were protecting women against the harsh working conditions. In South Africa, post 1994, there has been a shift in thinking in regard to the employment of women in the mines. WOMEN IN SOUTH AFRICA MINING In the words of the Minister of Women in the Presidency, Minister Susan Shabangu, “women must take centre [sic] stage as the country gears itself for the implementation of radical socio-economic transformation policies and programmes in the next five years” (SA Government News Agency, 2014). In as much as some progress has been made in advancing women, more needs to be done in order to realize sustainable benefits in the economy. The emancipation of women is a reality and remains top of the South African government agenda. From the Authors’ experience there are two types of men in the mines. The first group support change and see the value in it. To them, women in mining bring in the diversity and play the complementary role in achieving greatness. There is no fear of job security and humiliation but a great sense of “camaraderie”. The other group continues to enforce stereotypes, which works against the spirit of redressing the imbalances of the past."

Jan 1, 2018

By D. W. Park

Longwall mining is considered the most efficient underground coal mining technique in terms of coal extraction ratio, production rate, and safety standards. Due to the increasing demand for higher coal production, wider panel and faster face movement have become the recent trends. Thus, longwall mining can create unexpected threats such as roof falls, excessive face convergence, shield damage and numerous maintenance problems causing sudden interruption of coal production and serious safety hazards. A recent study at the University of Alabama is dedicated to develop LoSCoMS (Longwall Strata Control and Maintenance System) which integrates real-time shield monitoring, data presentation, analysis, forecasting, and warning modules. The main objectives of this system is to provide the stability and maintenance information, at every minute, such as high load, low setting pressure, leg leakage, etc., analysis of various mining and geological parameters to determine past and present roof characteristics and forecasting of loading patterns for the following mining cycles, next periodic weighting, etc. Using this unique system, mine operating personnel are well aware of past, present and future roof loading patterns at the longwall face, and thus, proper safety measures can be taken ahead of time.

Jan 1, 1997

By L. Stas

The authors have been interested in stress measurements in the rock mass for a long time. This paper describes the development of new apparatus for stress measurements in a rock mass. The principle of stress measurement by this device is based on the relief method as applied on the conical shaped surface of the bottom of a borehole. The design started based on the experience of K. Sugawara and Y. Obara who have been using the compact conical borehole over-coring system (CCBO). The conical shape of the strain gauge probe CCBO makes the fixation of the probe in borehole easy and, also, makes the measurement of stress in independent directions possible. The principle of the measuring method, the preparation of the borehole, the design of the probe for continuous measurement of stress during the course of overcoring are described. Also, a simplified version of the probe for long term monitoring of stress variations in the rock mass by means of the inserted body method and the initial laboratory results and in-situ testing of the development sample are described. Additionally, testing was done regarding the possible glues in relationship to the creep effect for this case.

Jan 1, 2006

By G. F. Revey

Most commercial explosives contain 70 to 94% ammonium nitrate, by weight. When portions of these explosives end up in shot rock and ore, through spillage or incomplete detonation, ammonia and nitrates leach out of them and into ground water. In recent years, State and Federal regulators have been applying more stringent water quality standards, particularly at new mines and development projects. Bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice at most mines, when mining conditions allow it. ANFO use is desired because it less costly than other explosives, but when spilled it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. They either control explosive losses, or they treat mine effluents at the end-of-pipe. This paper addresses the former solution --controlling explosive losses. For both packaged and bulk explosives, guidelines designed to limit losses during storage, handling and use, are described in detail.

Jan 1, 1995

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By Keenan. Albert M

The challenge of mining coal seams having a pitch of 30 degrees is one not frequently found in the United States, due primarily to the scarcity of such deposits. However, in the Thompson Creek District in Pitkin, Colorado, such a challenge exists to produce high quality medium volatile coking coal, and development of a longwall system is underway. The deposits under consideration are those of the Anschutz Corporation Inc. of Denver, Colorado, which are not in a virgin state. The properties were originally mined by the Colorado Fuel and Iron Corporation from 1894-1907, and by the Thompson Creek Coal and Coke Corp. from 1953-1966. Approximately five and one half million tons of coal have been mined by the above companies, attesting to its quality. The cessation of operations in both instances was occasioned by economics. Both companies employed a room and pillar system of mining, but being denied the use of high capacity mining and loading machinery because of the excessive pitch of the coal seam. This resulted in an unfavorable productivity expressed as output per man-shift, and thus the high cost of production occasioned by hand loading and semi-mechanization dictated cessation of operations. The specific location of these deposits are in Pitkin County,

Jan 1, 1971

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By Wayne A. Sadik

The mine ventilation system of the Henderson Mine provides a case study of designing and maintaining high-quality respirable air in a large underground mine with over 200 units of diesel-powered equipment. This system was designed with concern for minimizing exposure to personnel of siliceous dust, diesel exhaust, smoke, and potential fire hazards while optimizing general environmental air quality throughout the multilevel/multiheading operation. As a relatively new operation, the Henderson Mine incorporates a modern ventilating plant and mine de- sign as well as state-of-the-art technology where appropriate. Two main ventilation shafts approximately 2,300 ft (701 m) in depth (one intake, one exhaust) will handle 1.8 million cfm (850 m3/s) of air circulated throughout 60 miles (97 km) of drifting, providing the ventilation requirements for more than 25,000 diesel horsepower (18,642 kw) underground.

Jan 1, 1980

By J. Kretschmann, T. Rudolph, L. Michael, P. Goerke-Mallet

The mining value chain plays an important role in our societal development. Even in a circular economy, mining and raw materials are in great demand, and so are skilled engineers. In Germany, many students decide to pursue STEM studies in the tertiary degree. Nevertheless, the OECD reports low completion rates in obtaining the degree of studies [1]. Generally, the dropout rates in STEM education are high [2]. Many students have difficulties with basic subjects such as science and mathematics, in which they lack knowledge they should have acquired in school [2]. With the German STE(A)M project PepperMINT (https://peppermint.thga.de/), the Technische Hochschule Georg Agricola (THGA) offers a digital and open educational platform, as a dynamic, massive open, online course (MOOC) for students and prospective engineers. The project is funded by the RAG-Stiftung (RAG-Foundation; No. 20-0004). Using adaptable MOOC classes and applied examples from the wide-ranging cycle of mining activities, we motivate students to engage in STEM studies. Our adaptive and application-oriented content demonstrates the diversity of jobs and career paths in the mining industry. The integrations of applied examples and research activities of the Technische Hochschule Georg Agricola can increase the curiosity and motivation of learners. In mathematics, mine-surveiying technologies and geomonitoring methods (see figure 1) can be used to teach trigonometry. Additionally the concept of the free open online classes enables students in high school to get insights into the field of engineering before they decide the subject of their studies. For freshmen who already decided to pursue a STEM degree, the PepperMINT courses can help to identify and close knowledge gaps and to align different levels of knowledge within a heterogeneous student body. Empowering students in STEM education and integrating examples from mining research can help us train the mining engineers of the future.

Mar 2, 2022

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011