Search Documents

By B. K. Cantrell, D. H. Carlson, W. F. Watts, K. L. Rubow

The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH) regards "whole diesel exhaust" as "a potential occupational carcinogen." Threshold limit values (TLVs) are recommended for the gaseous pollutants CO, CO2, NO, N02, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality. Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulageway and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2 and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters. Concentrations of CO, C02, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3.

Jan 1, 1992

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950's resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world's largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

By J. A. Bleeck

A discourse on the relationship between industrial minerals and paper production, concentrating on high grade, ultra fine ground calcium carbonate (mean particle size less than 2 microns) and precipitated calcium carbonate. The scope of the paper encompasses four basic areas relevant to the topic: 1. A tutorial overview of the papermaking process with an examination of various industrial mineral components in that process; 2. A discussion of basic technological topics pertinent to the utilization of carbonate in paper with emphasis on the relative aspect. Of natural ground calcium carbonate (GCC) and synthetic precipitated calcium carbonate (PCC); 3. An overview of paper and carbonate market, in both the United State, and Europe with emphasis on (a) current status and future growth trend. Of such market., and (b) discussion of the major influences on growth and development of such market.; and 4. Identification and discussion regarding the principal producers in calcium carbonate markets serving the paper indu.try in Europe and North America.

Jan 1, 1993

The National Mining Hall of Fame and Museum (NMHF&M) will celebrate its 25th anniversary on Sept. 22, 2012 when the 2012 class is inducted during a special ceremony in Las Vegas, NV in conjunction with MINExpo 2012. The NMHF&M will induct four men representing the equipment manufacturing, minerals exploration, copper and coal sectors of the mining industry. The diverse cross-section of mining industry giants joining the hall of fame include Glen A. Barton, J. David Lowell, Samuel Newhouse and John Cleveland Osgood. They will join 214 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 25th Silver Anniversary Induction Banquet & Ceremony. These men were selected for being visionaries, leaders and ambassadors within their own sectors and across the industry at large.

Jan 1, 2013

By M. Bidart, V. Sawyer, M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas that are below the natural groundwater elevations. This necessitates dewatering, which requires a method for the disposal of the extracted water. Some of these open pits extend well below, the water table with dewatering volumes greater than 10,000 gpm (38,000 L/min). Some mines with large volumes of dewatering water have constructed reinfiltration basins to reintroduce the water into the groundwater system at a point some distance from the pits. This paper presents an overview of the state of the art of reinfiltration projects, including the permit process for such projects in Nevada. The paper includes the necessary engineering considerations.

Jan 1, 1997

By Peter N. Loncar

Most miners dream of finding a gold mine sometime during their mining careers, but not very often do such dreams come true. On the tenth day of September, 1962, our dream of finding gold came true when the results of the third drill hole were received. This was undoubtedly one of the most exciting days of our lives. Little did we realize then that this was the beginning of a major discovery destined to became one of the largest gold mines in the country. Discovering and mining gold is not entirely new, however, to Eureka. County a old Lynn Mining District in northeastern Nevada. Since 1900 there has been sporadic activity, mostly consisting of small lode mines and placers. These have produced totally about $300,000; and existence of our orebody would probably have remained unknown had it not been for the United States Geological Survey. The USGS extensively mapped the Roberts Mountain Thrust and published a paper indicating that mineral occurred along this fault and in some places was gold bearing. Utilizing this information, our Newmont Exploration geologists located an area in which: drills were brought in to test their theories. By keeping flexible in our thinning and working, we were able to bring a raw prospect to a producing mine with ore reserves of eleven million tons in a short three-year period.

Jan 1, 1965

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By W. C. Hellyer

The Granduc ore body is located beneath glacial terrain on the borders of British Columbia and Alaska, some 600 miles from Vancouver and 30 miles from Tidewater at Stewart, B. C. The concentrator and attendant facilities are located in wilderness country at an elevation of 2500 feet. The average annual snowfall is 65 feet. Surface facilities and ore body are linked by a 10 mile railroad haulage tunnel. This copper property has been developed by Granduc Operating Company on behalf of Newmont Mining Corporation and American Smelting and Refining Co. First production started in November, 1970. In August, 1966, Granduc Operating Company awarded an engineering and construction management contract to McKee-Swan Wooster, a joint venture of A. G. McKee of Canada and Swan Wooster Engineering Company Limited, to design a concentrator to treat approximately 7000 tons of ore per day. The isolated location of the Granduc ore body indicated comparatively high freight rates on consumable items of concentrator supplies such as reagents, grinding media, etc. A firm flowsheet for the flotation of the Granduc ores having been developed by the Danbury laboratory of Newmont Exploration Limited, attention was devoted to means of reducing operating costs. One obvious method was to reduce or eliminate the costs of steel grinding media by employing some form of autogenous grinding. two pilot plant operations were carried out at the facilities of Lakefield Research of Canada Limited, in which autogenous grinding of Granduc ores was investigated. The results of these investigations led to the selection

Jan 1, 1972

By D. A. Stanley

Researchers at BCD Technologies and the University of Alabama have applied three statistical techniques to the information contained in a large database of measurements from a phosphate ore processing plant. The rust, Principal Components Analysis (PCA), replaces many measured variables with a few fundamental and un-correlated variables. The second technique, Projection to Latent Structures (PLS), is an extension of PCA that explores the relation between variables identified as either independent or dependent. The third technique, Cluster Analysis (CA), is applied to the results of the PCA or the PLS calculations, and identifies individual data clusters that represent uniform operating conditions in the plant. All three statistical methods can be seen as geometrical operations on the data viewed as points in space. A Viewer gives a corresponding graphical presentation of the data points. This paper describes the use of the above three techniques and the Viewer to explore part of the phosphate flotation database.

Jan 1, 1998

By G. C. Presley

With plant construction scheduled for the Spring of 1997, U. S. Zeolites will become the new source for quality in natural zeolites. The company will selectively mine, dry process, package, and market a very high quality clinoptilolite possessing many unusual properties. These unusual chemical and physical properties provide a multitude of industrial, commercial, and consumer applications. Extensive testing has determined many potential applications.

Jan 1, 1997

By L. D. Ellison

The ventilation of a bituminous coal mine by means t of a Forced and, or, Exhaust system of ventilation is certainly not new to the mining industry, however, we know from experience that the ventilation of every coal mine presents a variety of problems which are in some instances approached by different methods or means, As in every such problem, there is some difference of opinion as to the advantages and disadvantages of s Exhaust versus Forced ventilation, particularly with regard to safe and effective ventilation of an active pillar area in a gaseous coal mine. We at Island Creek, certainly concede that it is possible to safely ventilate a coal mine by means of Forced ventilation, However, following many years experience in operating a coal mine in an extremely gaseous coal seam, we prefer using an Exhaust system, that is, to reduce the inside mine pressure to a minus atmospheric pressure by means of a mechanically operated fan. This method assures that the return air moving through established airways toward the fan will continue to move in that same direction for a limited time should the fan stop for any reason, also assuring that in the event of a large area fall, the air from the abandoned workings will move directly to the suction side or to the return airways.

Jan 1, 1960

By J. Fox, C. Allen, A. Greth, K. Kocsis

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water, and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contribute a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed. The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than of the diesel engines. Battery powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers, and (c) reduced mine operating costs due to lower ventilation requirements. This paper will highlight the health and cost benefits of using battery/electric fleets versus diesel fleets in deep and hot underground mines. The study analyzes simulations produced from thermodynamic ventilation models. Early simulations show significant cost reductions in terms of net present value (NPV) when comparing the air volume requirements for battery/electric equipment versus diesel powered equipment for the same production rate. INTRODUCTION The competitiveness of the world mineral market demands that mine operators continue to increase production and decrease costs as commodity prices fluctuate in often unplanned directions. This has forced underground mines to operate at deeper depths and to become more mechanized to remain competitive. Because of these changes, ventilation challenges have continued to increase as the mines combat an enlarged influx of contaminants such as heat and diesel particulate matter (DPM)."

Jan 1, 2018

By C. Anderson, B. Schug, C. Cristoffanini, S. Nazari

The Haile Gold Mine in South Carolina is increasing the automation level of their processing plant in order to improve operational stability. One step towards this goal is the application of a Digital Twin concept to provide Virtual Instruments. Haile has engaged ANDRITZ to implement Virtual Instruments at their grinding area hydrocyclones and at their tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The Digital Twin is a first principles IDEAS1 ™ simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions, and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters. INTRODUCTION OceanaGold’s Haile Gold Mine is located near Kershaw, South Carolina, about 50 miles southeast of Charlotte, North Carolina. This location was first mined in 1827, and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October, 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile Operation. The current operation began in 2017 as an open pit mine with additional underground resources. The nameplate throughput is 6,350 tpd ore, and 2017 production was 118k oz gold, with 140 to 155k oz gold expected in 2018. Proven and Probable reserves exceed 3 Moz. The process, as shown in Figure 1, includes a primary jaw crusher, comminution with a Semi-Autonomous Grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon in leach (CIL) leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile Operation’s inaugural gold pour took place January 20, 2017. Mine life is expected through at least the year 2030. Based partially on prior experience of some key OceanaGold personnel with automation services from ANDRITZ on other projects, OceanaGold decided to include ANDRITZ on the Haile project. The scope of these services for Haile included design and supply of the process control application software, an ANDRITZ dynamic process simulator for operator training, and ANDRITZ Advanced Control Expert (ACE) ®2 systems for the SAG mill, ball mill, and rougher flotation areas. Since startup, ANDRITZ has continued to provide services for the site, particularly related to PLC and HMI equipment, programming and support, ACE system expansion, and the implementation of Virtual Instrumentation. The implementation of this new Virtual Instrumentation technology at Haile is consistent with Haile goals: increased automation, a change in the role of the operator from interactor to monitor, and improved stability by removing human error.

Jan 1, 2019

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By Hajime Miki, Michael J. Nicol

Relatively simple techniques have been developed which enable the electrochemistry of sulfide minerals to be studied with particles varying in size from above 100 pm to less than 1 pm. Both oxidative and reductive processes have been studied wing the minerals pyrite, arsenopyrite and chalcopyrite. It has been shown that it is possible to completely oxidise or reduce the minerals during a single voltammetic sweep. The resulting voltammogram produces peaks which are characteristic of each mineral and can be used to qualitatively identify the minerals. In the case of chalcopyrite, it has been demonstrated that the charge involved in the anodic oxidation can be quantitatively related to the amount of copper dissolved. Quantitative information can be obtained using peak fitting techniques. Interesting differences in the behaviour of the minerals in sulfuric and hydrochloric acids have been observed, particularly in the case of pyrite for which a second major peak is obtained which has been attributed to the oxidation of elemental sulfur in the presence of chloride ions. The technique offers the possibility of providing mineralogical information of individual particles based on an electrochemical voltammetic finger print.

Jan 1, 2005