Search Documents

By K. C. Shaver

The Sloan Ranch kimberlite complex is located approximately 130 km north-northwest of Denver in the Precambrian core of the northern Colorado Front Range (Figure 1). A Devonian age for the complex is suggested by the fossil assemblages in limestone xenoliths (Chronic and others, 1969), and by paleomagnetism of the kimberlite (E. E. Larson, personal communication, 1986). The presence of diamond was first reported in rocks from the Sloan diatreme by McCallum and Mabarak (1976). Prior to this time, the distinctive- appearing host rock of the Sloan diamonds had been quarried for use as terrazzo stone; examples may be seen in the floors of the airports in Cheyenne and Laramie, Wyoming. The Minerals Division of The Superior Oil Company obtained a lease on the Sloan property in 1980. During the next four years Superior built and fine-tuned a highly efficient diamond recovery facility, explored and tested the Sloan deposit, and used Sloan as a site for testing numerous exploration techniques for future use in a continuing exploration program in the Colorado-Wyoming kimberlite province. The Sloan property was ultimately determined to be sub- economic, but the lessons learned there have been very helpful in subsequent exploration efforts.

Jan 1, 1987

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By F. Seymour

A modified 3D Lerchs-Grossmann (LG) graph tree algorithm is presented that generates the complete set of nested maximum valued pits in a single run. This modified LG algorithm looks at the relative strength (average value) of the branches (groups of blocks). Pointers are allocated and pruned until there are no members of weaker (lower average value) branches overlying members of stronger (higher aver-age value) branches. The final set of strong branches are listed in order of decreasing strength. The pits they represent form the maximum valued convex hull for a single variable pit limit parameterization. A description of the algorithm is given along with examples of how it has been applied at Newmont.

Jan 1, 1995

By H. Bogart

The Golden Sunlight Underground Mine located near Whitehall, Montana was portalled from the bottom of the existing Golden Sunlight Pit in July 2002. Gold was mined by sublevel stoping in the larger ore zones and longhole back stoping in the narrower ore zones. The stopes varied from 30 feet to 100 feet in width, extended up to 200 feet in height, and were completely unsupported. Underground production averaged 1,500 tons per day with a staff of35 people. The mine operated with a break-even cut-off grade of0.080 ounces per ton.

Jan 1, 2004

By F. G. Rinker

The world demand for metallized iron continues to increase, keeping pace with steelmaking requirements for lower cost hot metal. Virgin iron ore and in-plant oxide fines can be reduced to direct reduced iron (DRI) and hot briquetted iron (RBI). MR&E has developed an improved coal-based process for cost-effective production of either DRI or HBI. Starting with dry compaction, the process combines the latest technology for material preparation, rotary hearth furnace construction and environmental control. Coarse iron ore fines are blended with pulverized non-metallurgical coal to produce a highly metallized (>90%) product. This paper presents production and installation cost data based on operating and under-construction iron oxide reduction facilities.

Jan 1, 1999

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By Theodore J. Barrett

[One of the earliest records of pillar removal can be found in the 16th Chapter of Judges in the Old Testament. Here we read where the mighty Sampson removed the pillars from beneath the prison house causing the collapse of the structure resulting in his own death along with the deaths of the 3,000 Philistine occupants. Our problems at the Mi Vida Mine differ somewhat from those of Sampson of old, in that it is our aim first to remove the pillars and get out from under the back before the "house falls in" and, secondly, to remove the pillars without the lose of a single life or without even a single casualty. As of January 15, 1959, the Mi Vida accident record stood at 772 days without a lost-time accident]

Jan 1, 1959

By Glenn A. Shirey, Robert D. Stoessner, S. Gopalakrishnan

Under a contract awarded by the U.S. DOE-PETC, the Pennsylvania Electric Company and New York. State Electric and Gas Corporation are conducting a test program to evaluate and optimize the performance of a two-inch air-sparged. hydrocyclone (ASH) for cleaning fine coal. The test program is being conducted at the Homer City EPRI Coal Quality Development Center, utilizing Upper Freeport coal classified to minus 0.15 mm as the process feed material. A matrix of experiments has been conducted to establish the influence of significant design and operating variables (including overflow and underflow orifices, inlet slurry pressure, airflow rate, and reagent dosage) on the production of deep cleaned coal. Performance of the ASH is being compared to conventional froth flotation, utilizing advanced techniques and selected flotation reagents. This paper focuses on work completed to-date to optimize the performance of the air-sparged hydrocyclone for cleaning fine coal. INTRODUCTION The Pennsylvania Electric Company (Penelec) and New York State Electric and Gas Corporation (NYSEG) have been evaluating advanced fine coal cleaning processes for the production of compliance grade coal (1.2 pounds S02/million Btu). Laboratory bench-scale froth flotation results were compared with results of advanced flotation processes as performed by various organizations, utilizing the same coal feed. Among the processes evaluated, the air-sparged hydrocyclone (ASH) - developed by Dr. Jan Miller at the University of Utah - was considered to offer the best potential for retrofitting into an existing coal preparation facility because of the increased capacity per unit volume. The ASH has been shown to process over 100 times the throughput of conventional froth flotation cells. In May of 1988, Penelec/NYSEG was awarded a contract from the Department of Energy's Pittsburgh Energy and Technology Center (DOE-PETC) to optimize the performance of a five cm (two inch) ASH for producing compliance grade coal from raw classified minus 0.150 mm (1.00 mesh) Upper Freeport coal, and to compare its performance with conventional froth flotation utilizing advanced techniques and selected flotation reagents. The test work is being conducted at EPRI's Coal Quality Development Center (CQDC) in Homer City, Pennsylvania, utilizing a circuit processing 0.10 to 0.25 tons of coal per hour. Other members of the Penelec/NYSEG contract team include the University of Utah, Advanced Processing Technologies, Inc., Davy Dravo, Kaiser Engineers, Ebasco Services, and Management and Technical Systems. ASH DESCRIPTION AND OPERATION The ASH-2 System is a five cm ID (actually 4.76 cm) air-sparged hydrocyclone manufactured by Advanced Processing Technologies, Inc., under license from the University of Utah, for the purpose of research, evaluation and development. A schematic drawing of the air-sparged hydrocyclone is presented in Figure 1. Basically the air-sparged hydrocyclone consists of two concentric right-vertical tubes, a conventional cyclone header at the top, and a froth pedestal at the bottom. The inner tube is a porous tube through which air is sparged radially. The outer nonporous tube simply serves as an air jacket to provide for even distribution of air through the porous inner tube. The slurry is fed tangentially through the conventional cyclone header to develop a swirl flow in the radial direction. Air is sparged through the jacketed, inner porous tube wall and is sheared into small bubbles by the swirl flow. Hydrophobic particles in the slurry collide with these bubbles and, after attachment, are transported radially into a froth phase which forms on the cyclone axis. The froth phase is stabilized and constrained by the froth pedestal, thus moving towards the vortex finder of the cyclone header and discharged as an overflow product. Hydrophilic particles generally remain centrifuged in the slurry phase and are discharged as an underflow product through the annulus created by the froth pedestal.

Jan 1, 1989

By Karl S. Vorres

Coal my not seem like it, but it is a perishable commodity. The basic coal scientist cannot always replicate earlier experiments with a given sample because of changes that have taken place in the sample. This has led to a stated need for stable samples Coal looks like a uniform black solid to many people, but it does vary in its composition from state to state and mine to mine it also can be shown to vary significantly within a mine or seam. These variations have led to a stated need for consistent samples.

Jan 1, 1985

By M. Canty

This paper presents results from pilot-scale and field testing of an innovative technology that uses sulfate-reducing bacteria (SRB) to treat and control acid mine drainage (AMD). Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides. The bicarbonate produced serves to help neutralize the drainage. Pilot-scale metal-removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium and 96% for copper. However, the iron and arsenic removals were not as effective as the aforementioned metals. This was largely attributed to high levels of iron and arsenic that contaminating the organic substrate. There was evidence that both adsorption and sulfate reduction were occurring within the reactors. The SRB field demonstration involved using the flooded subsurface mine workings of the Lilly/Orphan Boy Mine near Elliston, MT, as an "in situ biological reactor." In the mine, high removal efficiencies were observed for aluminum, cadmium, copper and zinc (70% to near 100%) during the four years of monitoring. However, for reasons similar to the pilot scale testing, low removal efficiencies were observed for arsenic and iron. Sulfate reduction was evident by measured decreases in sulfate and the detection of soluble sulfide within the mine water.

Jan 1, 2000

By D. A. Barr

The Galore Creek copper deposits lie in the Stikine River district of northwest British Columbia, a largely undeveloped region which possesses rugged mountain terrain with deeply incised valleys which support dense undergrowth. Timberline is normally at about 1300 m (4265 ft) and the higher levels contain glacial systems and large ice fields with peaks rising to 3500 m (I 1,483 ft). A location map of the Galore Creek area is given in Fig. 1. In the late 1920s, field parties under the direction of F.A. Kerr (1948) of the Geological Survey of Canada completed geological surveys of the district. Primary access for this work was provided by riverboats on the Stikine and Iskut Rivers. Kerr's party had to contend with extremely difficult travel conditions that required considerable backpacking, augmented by pack dogs in certain cases. Absence of ground control led Kerr to establish his own topographic maps. Among the geological data established was the recognition [ ] that small bodies of orthoclase porphyry in the district are often well mineralized with base metal sulfides. Copper mineralization in the upper Galore Creek valley, a tributary of Scud River which flows into the Stikine River some 80 km (50 miles) south of the small settlement of Telegraph Creek, was originally discovered during aerial reconnaissance by M. Morrison and W. Buckholz while prospecting for Hudson Bay Exploration and Development Co. Ltd. in 1955. Malachite- and azurite-stained out- crops in several parts of the Galore Creek watershed are clearly visible from distances of 500 m ( 1640 ft) or more. Claims were staked in 1956 and the copper showings were partly mapped, trenched, and investigated by shallow diamond drilling. Because of the remoteness of the area and higher priorities for expenditures elsewhere, no further work was undertaken and most of the claims were allowed to expire.

Jan 1, 1991

By Henning Schwarz, Ade Ogunsola, Anas Almousa

"The Riyadh Metro, commissioned by Arriyadh Development Authority “ADA” - the executive arm of The High Commission for the Development of Arriyadh -, forms part of a new public transport-system of Saudi Arabia’s fast growing capital city. The Design & Build project consists of 176 km of Metro Line with 57 km of tunnels. Beyond the Design and Construction, an additional aim of the ADA is to introduce up-to-date methodologies and improve safety in construction projects. A systematic dilapidation survey of buildings and infrastructures was a prerequisite for designing the required instrumentation and monitoring tools. Site investigations required of existing methodologies and the use of geophysical methods for achieving reliable results. Large diameter TBM tunneling is challenging in hot weather conditions and karstic ground. The present paper shows how modern technologies for underground construction are introduced into the local industry and gives an outlook on future projects in the Kingdom of Saudi Arabia. INTRODUCTION Riyadh, the capital city of the Kingdom of Saudi Arabia, is a fast growing city with more than 5.7 million inhabitants. The growth of the city is linked to the recent history of the Kingdom, where some initial milestones from the 1950’s can be highlighted: Revenue generation from the exportation of oil from the Kingdom; downstream investment of oil revenue in the reconstruction and development of the Kingdom; a general plan for the settlement of the Bedouins; the provision of a public electricity network for the city; the opening of the Riyadh - Dammam railway corridor providing a link from the capital to the Eastern Region; the commissioning of Riyadh airport (converted to Riyadh airbase, after the opening of King Khalid International Airport in 1983); and the relocation of ministries and other central government agencies in 1955. In 1974, The High Commission for the Development of Arriyadh was established as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority “ADA”, established in 1983 is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions. The ADA’s president is a member of the High Commission (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city of Riyadh."

Jan 1, 2016

By Lester F. Sanford

Located in the Santa Cruz Mountains eight miles north of the City of Santa Cruz and inland from the coast, lies a typical beach sand consisting of quartz and feldspar grains of the Santa Harguerita formation of the middle tertiary age, Reserves of over twenty-five million tons of this sand form the deposit presently being harvested by Pacific Cement & Aggregates, a Division of Lone Star Cement Corporation. The deposit ranges from 350 to 700 feet above sea level and varies from two percent passing a 200 mesh screen to ten percent retained on a ¼ inch screen (see Figure '#l) In 1929 the first sand plant went into operation at this site. It was replaced by a new plant in 1937. This plant continued operation until the middle of 1965 when replaced by the modern plant described in this paper.

Jan 1, 1967

By John Duff Erickson

Determination of the final pit limits of an open pit copper mine is a problem that has far reaching effects on the life, profitability and operation of a mine. The solution to this problem requires that all of the significant variables affecting the final pit limits be considered together with corporate objectives as the guiding principle. This paper discusses the use of these variables and how they should be applied to plan the future of a mine. The objectives of a final pit plan; are determination of the extent and location of ore reserves, the allowable stripping to be accomplished to uncover the ore, the final pit surface intercept, final pit topography and the contained metal values in both ore and waste. The objectives of the plan must be consistent with corporate objectives as they pertain to profit, future investment in the mine, return on investment, alternative investments, conservation and perpetuation of the corporate entity. The subject will be treated in three parts: economic considerations, effect of leaching and pit design technique. At the outset, it is assumed; that the extent of and metal values in the mineralized area to be considered have been reasonably defined by development drilling and sampling.

Jan 1, 1968

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

By J. Kennedy

Rare Earths: Understanding The United States complete failure of status and relevance in Rare Earth Oxides, Elements and Alloys. Although rare earth oxides are strategic and critical in their own right, elements and alloys are even more important for the development of "Green Technologies" and advanced weapons systems. America does not have an active domestic source of rare earth oxides. America does not have any Heavy Rare Earth Elemental or Alloy capabilities. The magnitude of this failure continues to become more apparent as the manufacture of REO based electronics and magnetic components moves eastward towards China. China has succeeded in outmaneuvering The United States and the world in its quest to control the Rare Earth Oxides, Elements and Alloys, and the many industries dependent upon REO. What can be done?

Jan 1, 2010

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By L. U. Spellman

Atlantic Cement Company's new multimillion dollar, 10,000,000 barrel per year cement plant went into full operation in February, 1962, bringing into reality a new concept in the distribution of Portland cement. The Cerro and Newmont Mining Corporations, well established in the mineral extraction and dressing industry, backed the venture. To take advantage of the, economics inherent in single production units of large capacity, it was necessary to first find a market' capable of absorbing such large quantities. Cement can be economically shipped by rail and truck about 200 miles. Beyond' that radius from the producing facility the freight costs become prohibitive. No single marker area within that radius exists which could absorb such a large volume of cement. However, water transportation provides a relatively inexpensive method of transporting bulk products many times over such a distance. Thus, it was decided to locate the producing facility near a deep water port which had ready access both to the Atlantic Ocean and, just as important, a good source of raw material. An extensive feasibility study was made and the site at Ravena, New York on the Hudson River near Albany was chosen. Here, vast quantities of limestone in the foothills of the Catskill Mountains are found within a short distance of-the deep-water Hudson River.

Jan 1, 1964

By John S. Lagarias

While systems to remove sulfur oxides from flue gases have been used at coal fired power plants since 1931, critical need for flue gas desulfurization has only occurred since the late 1960s following the passage of the Clean Air Act Amendments. Commercial and advanced flue gas desulfurization processes (FGD) are reviewed. Advantages and disadvantages of the processes are discussed. Regulatory requirements leading to the development of FGD systems are identified. The location and operation of coal fired plants may be determined more and more by the regulatory requirements for sludge disposal, waste, water discharge and air emissions.

Jan 1, 1978

By D. W. Rierson

Svedala has a ported kiln process, designed specifically for the direct reduction of pelletized or natural lump iron ores. The process is called ACCAR. This ported kiln technology has been coupled with Svedala's GRATE-KILN System, for iron ore pelletizing, into the GRATE-CAR System for the reduction of fine grained ore concentrates through the steps of agglomeration, induration and reduction in a single production line. Additional applications of the GRATE-CAR System include: the recovery, agglomeration and reduction of steelmill waste oxide fines and the use of minus 6mm size natural lump ores to produce a highly metallized pellet agglomerate. Svedala conducts tests to confirm certain operating parameters through process simulations of the GRATE-CAR process. These tests are conducted at Svedala's Process Research and Test Center, Oak Creek, Wisconsin. Svedala also assesses issues of process variables, heat transfer, equipment sizing, retention time and endothermic demand associated with iron ore reduction using natural gas or coal as the reductant. The purpose of this paper is to present the GRATE-CAR processing concepts, the commercial production line and the testing procedures associated with investigating potential raw materials.

Jan 1, 1997