Search Documents

By James L. Hendrix, David Castillo

Cyanidation is one of the most common practices used in the extraction of gold and silver. One method of application is heap or dump leaching which entails the leaching of the gold or silver ore by spraying or dripping a cyanide lixiviant over the ore and collecting the effluent. The ore is placed on what is known as a leach pad system. A typical leach pad system consists of a foundation, a leakaqe detection system, a liner, and a cover layer (Strachan and van Zyl, 1988). There are many types of liners available for use. The type of liner depends upon what type leaching pad system us used. Generally, leaching pad systems can be categorized into two types: an expandable pad and a reusable pad. An expandable pad exposes the liner to the elements only in the initial stages of ore placement on the leach pad system. A reusable pad exposes the liner to the elements on a periodic basis. In addition to the exposure to the elements, the liner is also under the stress of the ore placed on it and the stress of the vehicular traffic across it. These stresses and exposure to the elements are the major causes of liner failures, which can appear as punctures, tears, cracks, and deterioration. Because of the possibility of the failure of the pads to contain cyanide-laden solutions the designs for liners of pads and ponds have become more and more stringent. Currently, though, there is some recognition that in some locales such stringent design criteria may not be required (Chatwin, 1989). Some soils have significant cyanide attenuation and degradation capacity. It has been found that soils containing carbon- aceous materia1 wi11 remove cyanide from solutions percolating through them (Chatwin, 1989). Of course metallurgists have long recognized the deleterious effect of carbonaceous material in the mill circuit. Sheridan, et a1 (1988) have shown that WAD cyanide is detected in the effluent of a 2 m column filled with ground carbonaceous ore only after it had been continuously washed with greater than 9 pore volumes of NaCN solution. It was decided to examine the potential of successfully attenuating cyanide by placing an organic material layer between a 1iner and the prepared soil base. One consideration for the selection of the organic material was cost. Sawmill wastes, ground agricultural wastes (such as corn cobs), and other organic wastes were considered. But the first waste to be tested was a product found at any metropolitan area, sewage sludge.

Jan 1, 1990

By A. Juganda, Jr. Bogin, J. Brune, J. Grubb, S. Lolon

"Face ignitions at the longwall face are a serious hazard in underground coal operation that can lead to a major mine explosion. Despite having methane monitoring system mounted on the shearer and at various locations on the longwall face, undetected accumulations of methane can still occur and result in face ignitions. With the use of Computational Fluid Dynamics (CFD), the interaction between the air flow at the longwall face and factors that contribute to the accumulation of methane around the longwall face can be modeled and visualized in great detail. The results confirm that the tailgate corner of longwall face is a critical area that is prone to face ignitions and needs to be properly monitored. The occurrence of roof falls on the tailgate entry inby the face and/or poor caving conditions behind the shields can pose a safety risk in the longwall operation. Poor gob caving can lead to insufficient face air quantity to dilute methane at the tailgate corner, while blocking of tailgate by a roof fall can carry methane contaminated air from behind the shields back into the face near the tailgate corner and pull the explosive gas zones (EGZs) inside the gob closer to the face. INTRODUCTION Ignitions of accumulated methane gas at longwall faces are well known to be among the major causes of methane explosion in underground coal longwall mining operations. Some of these ignitions can lead to major mine explosions, such as the Upper Big Branch mine disaster in 2010, in which methane migrated from the gob to the shearer cutting drum where it was ignited, resulting in a major mine disaster (Phillips, 2012). History has shown that, despite having methane monitoring systems mounted on the shearer and various locations at the longwall face and alarms set to 1% CH4 (Mine Safety & Health Administration, 2012), undetected accumulations of explosive methane-air-mixtures can still occur and result in face ignitions. Recent study by Verma and Brune (2016) state that frictional ignitions on longwall faces contributed to 379 incidents or 23% of the total 1,637 cases of face ignitions recorded from 1983 to 2014. The common cause of mine explosions usually involves poorly designed ventilation systems, insufficient ventilation, and inadequate monitoring in critical areas that are prone to methane accumulations. In longwall operation, the tailgate corner of the longwall face can be considered as one such critical area. On-site studies by Krog et al (2006) and Thakur (2008) show that increasing the longwall panel width may also increase cumulative methane emissions at the tailgate. There are also indications that increasing longwall face lengths can result in an increase of the void space behind the face under certain roof conditions (Schatzel et al, 2006). This may cause higher leakage rates from the face to the gob, thus reducing the amount of fresh air available at the tailgate."

Jan 1, 2017

By Cal D. Iles

Decreasing ore grades and increasing labor and material costs have seriously eroded the economic vitality of many mining operations. Coupled with global economic stagnation and recession in the early 1980's, these conditions have forced reevaluation of operating strategies and methodologies with the objective of remaining competitive in a world marketplace. A concept offering large potential benefits is hardrock portable crushing and conveying. Implementation of this system at Duval Corporation's Sierrita open pit copper-molybdenum mine (Figure 1) has significantly reduced mining costs, becoming a major part of Sierrita's cost reduction strategy. Located 48 km south of Tucson, Arizona, the 209 000 t/d property has one portable 60x89 gyratory ore-crusher in operation with tentative plans for two additional units.

Jan 1, 1985

By Donald G. Dahle

Project Payette is a conceptual nuclear experiment under the Vela Uniform program intended to further evaluate the mechanism of seismic decoupling. Vela Uniform is a Department of Defense program to improve this country's capability to detect, locate and identify underground nuclear detonations. This program evolved from recommendations of the Panel on Seismic Improve¬ment, (Berkner Panel), an officially appointed group of noted U. S. scientists. This Panel, taking note of difficulties in detecting the differences between some underground nuclear detonations and some earthquakes recommended a program of increased basic research in seismology. The theory of decoupling, Which involves possible reducing of seismic motion resulting from underground explosions by reducing the coupling or physical linkage between the explosion and the geologic environment, was investigated by Dr. Albert latter and his associates at RAND during the late 1950's. The concept has been further investigated theoretically by scientists of the Lawrence Radiation Laboratory and the Sandia Laboratory. The theory has been tested experimentally under Vela Uniform Projects Cowboy, Dribble and Sterling. The Salmon Event of Project Dribble was a tamped (with the explosive in firm contact with the geologic formation) nuclear detonation 2700 feet below ground in the Tatum Salt Dome. Project Payette, if found to be feasible and if authorized for actual execution, would become a decoupled experiment in the same environment.

Jan 1, 1968

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By Randall E. Brown

Irrigation simulates a climate change so that crops can be grown that otherwise would not thrive. The abundant sunshine and warm weather of many arid regions induces a rate of growth in excess of that in cooler, moister regions. Hence, the arid part of eastern Washington, traversed by the Columbia River, is admirably suited to irrigation. The Pasco Basin lies in south-central Washington at the south end of the Columbia Basin Irrigation Project of the U.S. Bureau of Reclamation. The Basin, because it lies in the rain shadow of the Cascade Mountains, receives only 6 to 10 inches of precipitation a year with somewhat greater amounts, commonly as snow, on the higher hills. Recent extremes included 3 inches of precipitation from August 1967 to August 1968, and 12 inches in the succeeding "12 months. Most of the precipitation falls during winter. If it were to fall in summer or were evenly distributed throughout the year, evaporation rates probably would produce a true desert.

Jan 1, 1971

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By Bobby J. Timmons

Luck; blind, beginner's, fisherman's, or whatever type, plays an important role in romance, racing, football, gambling, and mineral exploration. However, for each of these; education, training, technique, and experience are necessary for a long, continuous, successful relationship. Success, no matter how obtained, is easier to defend than almost success, regardless of the education or the degree of refinement of the seeker. Similarly, investment dollars are more readily available to a successful, uneducated and unscientific practitioner than to his beginning or unlucky professional counterpart.

Jan 1, 1983

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O'Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By · J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit optimization stages of a mining project. This paper presents an approach for optimizing final pit limits for a highly variable and geologically complex gold deposit. A heuristic pit optimizer is used to manage the effect of geological uncertainty in the resources within a pit shell with multiple uncertainty rated solutions. The uncertainty rated pit shells follow the meanvariance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk management framework to further eliminate sub-optimal solutions along the efficient frontier. This results in a smaller set of final pit shells that could be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits and two regions are targeted as potential regions for further exploration.

By J. Driscoll, T. Morson, Ross M. Workman

The study investigates the effectiveness of the canopy air curtain (CAC) in reducing respirable dust exposure for shuttle car and ramcar operators in underground coal mining. Field testing showed that the CAC reduced dust exposure by 11-34% overall and by 57-65% during ramcar loading by the continuous miner. These results demonstrate the CAC’s potential as a significant dust control device.

Feb 19, 2022

By T. Ritzel

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels at Cyprus Sierrita. The predictive program was initiated by Cyprus Sierrita and P&H Mining Equipment at the Cyprus Sierrita Mine in Tucson, Arizona during August of 1996 on the P&H model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By Yeonuk Choi, Patrick R. Taylor, Lyle Cunningham

Laboratory experiments have been performed to evaluate the potential for metal removal and recovery from river bed tailings by ferric chloride leaching. The lead, zinc, silver and other metals in the river bed occur due to the old method of dumping mill tailings into rivers. This was practiced prior to the introduction of tailings impoundments. The effects of the leaching method, leaching time, pulp density, ferric chloride concentration, and leaching temperature on the rates and recoveries of lead, zinc and silver were studied. The effects of pulp density and leaching temperature were significant on the extraction rates of lead, zinc and silver. The lead content in the leached tailing was reduced to 0.023 percent, when using an 353O K leaching temperature and 0.384 g of FeC13/1 g of sample.

Jan 1, 1992

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010