Search Documents

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By Matthew Price, Laura Brown, Atulya Verma, Samantha Espley

Burst-prone conditions are a significant hazard in deep hardrock mines, elevating the risk to excavation stability and, more importantly, to worker safety. As mining progresses deeper, induced stress changes may trigger the initiation of rock failure processes which can be detected and recorded as mine seismicity. The implementation of seismic monitoring and routine seismic data analyses enables mine seismicity to be quantified spatially, temporally and on scale. The ability to quantify and characterize mine seismicity offers the opportunity to gauge seismic hazard, identifying high risk zones for mitigation against burst-prone excavation failure. Over the last decade, the Mines Technical Services (MTS) group at Vale Canada Limited’s Garson Mine assessed seismic hazard with the objective of assigning practical mitigating controls to zones identified as having a high rockburst potential. Initially, seismic hazard was computed using the Seismic Excavation Hazard Mapping (SEHM) software developed by the Mining Innovation Rehabilitation and Applied Research Corporation (MIRARCO) at Laurentian University, Canada. More recently, Vale Sudbury Operations partnered with the Australian Centre for Geomechanics and the University of Western Australia’s mXrap consortium. Through the consortium partnership, MTS at Garson Mine implemented the mXrap seismic data analyses platform, including the grid-based seismic hazard assessment tool. Building on 10 years of seismic hazard assessment experience at Vale Garson Mine, this paper summarizes a comprehensive case study, comparing the two tools (SHEM and mXrap) used at Garson Mine to assess, quantify, and represent seismic hazard. Subsequently, results of the Garson Mine comparative seismic hazard study will be discussed, emphasizing the need for an all-inclusive hazard assessment tool, focused on delivering practical mitigating controls that further enhance the overall safety of seismically active underground mines.

Apr 26, 2022

By G. B. Misra

Attempts have been made during the last three decades to establish a correlation between respirable dust dosage and the degree of progression of pneumoconiosis or silicosis amongst mine workers. Fair correlation has been possible only after the Johannesburg Pneumoconiosis Conference established mass concentration of dust in the respirable size range as the true measure of the incidence of pneumoconiosis. The author had established a good correlation between cumulative total respirable dust dosage as well as cumulative silica dosage and the category of pneumoconiosis according to ILO classification at Mufulira Copper Mine. Studies at Hutti also show a linear relationship between the average cumulative dust and silica dosage md the category of pneumoconiosis. However the maximum tolerable cumulative dust dosage for - prolonged exposure is 182 mg month/m3 - at Hutti as compared to 275 mg month/m3 at Mufulira. Similarly the maximum tolerable silica dosage for - prolonged exposure is Only 35 mg month/m3 at Hutti as compared to 55 mg month/m3 at Mufulira. The TLV for dust concentration at Hutti works out at 0.6 mg/m3 compared to 1.1 mg/m3 at Mufulira and the TLV of silica concentration at Hutti is 0.117 mg/m3 compared to 0.25 mg/m3 at Mufulira. The Hutti figure is however, closer to the TLV of 0.1 mg/m 3 recommended by ACGIH.

Jan 1, 1987

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

By Gary L. Simmons

Noranda's Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area. Applications in the minerals industries include calcium carbonate, talc, barytes, mica, diatamaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc. The basic principles can be extended to provide continuous drying and delivery of discrete particles from a wet process slurry. The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques. Mean particle sizes in the order of 1 micron are achieveable from pre-milled feeds, or maintained from similar slurries in the drying mode. Aspects of feed preparation and multi-stage processing are discussed.

Jan 1, 1983

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

By Romeo S. Jurani

Bulkspray cooling has been economically applied in cooling the hot environment of South African gold mines for the past two decades. Its success in that country led to its introduction at Gulf Mineral Resources Co.'s Mt. Taylor Mine in 1981 when increased drifting imposed additional cooling requirements. The bulkspray cooler developed and used at Mt. Taylor has a heat transfer capability of about 500 to 1500 kW. It is compact and portable, designed to be moved as required to maintain working temperatures in the advancing drift faces.

Jan 1, 1983

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By K Timtner

As shown in former publications there are problems in load sharing of backstops in multiple drives of conveyors. Therefore, detailed calculation methods and design recommendations are required. In this paper various designs of load sharing methods are described and a dynamic torque calculation method will be presented. With this method the loadsharing properties for low and high speed backstops are calculated and compared. These properties depend on the spring characteristic of the drive train between backstop and load. Furthermore, the properties depend on the method of torquearm support and shock absorber configuration. Remarkable differences for external and internal backstops are shown

Jan 1, 1998

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987