Search Documents

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By D. Wenstrup, K. Perry, J. Hatfield, P. Sainato, B. Lusk

Concrete-infused cloth is used in several civil and mining surface applications whose circumstances are similar to some of those in underground mining. A feature of this material is that it cannot be overhydrated. In underground conditions, however, the excess supply of water to the cloth for hydration could lead to muddy and potentially unsafe working conditions, as well as resource wastage by supplying more water to the construction site than is needed. The objective of this study is to verify the water-to-cloth ratio and study the effect of hydration level on the strength of the Concrete Cloth product. We found that the strength increases with increased hydration up to a 1:2 water-to-cloth ratio by weight, after which the strength holds steady regardless of additional hydration. This confirms the 1:2 water-tocloth ratio by weight for hydration and confirms that strength is retained even if the cloth is excessively hydrated.

Jan 1, 2014

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By H. Sahay

The current Canadian coal production is approximately 57x106 tonnes per annum of which some 25 million tonnes is exported. Two thirds of the Canadian output is classified as thermal and one third as coking or metallurgical coal. The Canadian coal industry, like the industries in some other industrialized nations, has gone through a cycle of ups and downs. The current world vide recession and stable oil prices have somewhat dampened the plans for a further growth of this industry - albeit temporarily. No new mines are expected to be developed within the next few years. However the production is projected to increase to 60x106 tonnes in 1985 increasing to an estimated 75 to 80x106 tonnes by 1995. The Canadian mines are highly mechanized and are willing to employ the modern technology to maintain its competitive position in the world's coal market. This paper reviews the recent technical developments which continue to improve resource recovery and productivity.

Jan 1, 1986

By Dave Watson

Henderson Mine personnel have more than 20 years experience and have placed more than 400,000 m3 (520,000 cu yd) of shotcrete and concrete. Over the last 20 years, the mine has used a variety of equipment to place concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Recently, the mine received a state-of-the-art wet shotcrete placer. The batch plant was automated, and a mobile concrete-form jumbo was fabricated. The mine will also receive a new concrete transport truck. Henderson’s background The Henderson Mine is owned by Climax Molybdenum Co., a unit of Amax, Inc. It is an underground, primary molybdenum producer near Empire, CO. The mill is located between Silverthome and Kremmling, CO and is connected to the mine by 16 km (10 miles) of underground and 8 km (5 miles) of surface track. Except for the ore haulage system which is powered by overhead trolley, all mobile equipment is rubber-tired and diesel-powered.

Jan 1, 1992

By L. Vinnett, J. Yianatos, S. Flores

"A numerical conditioning analysis for mineral recovery estimation was performed for industrial flotation plants, considering the copper (Cu), molybdenum (Mo) and iron (Fe) separability. A modified relative condition number, ?, was presented that allowed sensitivity analysis to be evaluated for the component recovery by means of an analytical formula. This closed form made it possible for the error propagation to be determined from feed, concentrate and tail grades with different orders of magnitude. The ? parameter can be evaluated using available grade data from the design criteria or historical mass balances, in which the variability is typically unknown. Reconciled data from different Cu/Mo concentrators were employed to evaluate the effect of small numerical disturbances in the grade data on the mineral recovery estimation. Higher error propagation was typically observed for Fe. The Mo minerals presented numerical problems, mainly in second cleaners and in the first cell of rougher banks. Lower condition numbers were observed for Cu due to the higher flotation rates.Mass-balance data reconciliation without redundancy was evaluated for a typical Cu/Mo flotation circuit using relative error minimization. Significant relative errors in the mineral recovery estimation were obtained with nonreconciled data in ill-conditioned problems. Negligible improvements in the mineral recovery estimation because of the data reconciliation with regard to the nonreconciled approach were obtained in well-conditioned problems. In addition, the improvements in mineral recovery estimation by using Cu, Mo and Fe in the data reconciliation were nonsignificant with respect to using only the best-conditioned component in well- and ill-conditioned problems.Despite the effort in data reconciliation and data repetition, poor performance may be obtained in ill-conditioned problems, which can deteriorate the flotation rate characterization. The error propagation has a negative impact on the mineral recovery of the first cell, which may significantly bias the flotation rate characterization of both valuable and nonvaluable elements.IntroductionMass balances have been extensively used in flotation processes to determine the mass flowrates (production) and mineral recovery (efficiency) of valuable minerals. Simple relationships for steadystate processes based on the feed, concentrate and tail grades can be obtained by taking a black-box approach. However, the calculation of concentrate flowrates from different components of the system, such as size fractions, chemical elements or minerals, does not satisfy the mass-conservation principle because of measurement errors (Smith and Ichiyen, 1973; Romagnoli and Sánchez, 2000). Mass-balance data reconciliation allows for obtaining a unique solution that satisfies the total and component mass balances, making small adjustments to the process data and taking advantage of the information redundancy (Narasimhan and Jordache, 2000). This methodology, which is based on a constrained weighted least-squares minimization, has proved to be robust when measurement errors are normally distributed, in the absence of gross errors.Commercial software has been developed to conduct massbalance data reconciliation in flotation processes, including MATBAL (Algosys, 2002), BILMAT (Algosys, 2013), JKMultibal (JKTech, 2013), BILCO (Caspeo, 2013) and HSC Chemistry (Outotec, 2013), which accomplish the reconciliation using known data accuracy in the optimization problem. The data accuracy can be obtained by sampling a stream n times in a run, known as repeats, each with independent chemical assays. Some unmeasured variables can be estimated using the measuring redundancy and sensor location. At present, grade and flow rate sensors may be incorporated in flotation to conduct real-time mass balances. However, a lack of sensor calibration and maintenance for suitable online measurements hinders the quality of the information. In"

Jan 1, 2016

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By William Petruk

Lithium bearing lepidolites from three deposits in the province of Goias in Brazil were investigated to determine whether there is a correlation between the lithium content of the mineral and the colour of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high grade ore zones. It was found that mauve-pink lepidolite associated with pink tourmaline, and brownish lepidolite associated with black tourmaline have high lithium contents, but the colour of lepidolite is not due to lithium. The pink colour of lepidolite and tourmaline is likely to Mn3+, and the brownish tint of lepidolite and black colour of tourmaline to Fe3+. Lepido lites appear to be lithium-rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or-Fe3+.

Jan 1, 1985

By Roshan B. Bhappu

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientific research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump leaching process and discusses salient features and parameters that may be helpful in improving such operations.

Jan 1, 1968

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By J. D. Miller

On the basis of nonequilibrium zeta potential measurements by laser-Doppler electrophoresis, the sign of the surface charge of alkali halides in their saturated brines has been established. The results are generally as expected from simplified lattice ion hydration theory. This recent electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble-salt flotation systems suggests that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation results confirm this surface-charge/collector-colloid adsorption model and are presented herein.

Jan 1, 1992

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By Shosei Serata

In the past, salt cavities for storage of liquid and gaseous fuels have been developed and operated using practical experience as a guide rather than rock mechanics principles and practices. Although many salt cavities are still operating satisfactorily. some of them are beginning to show various problems associated with long-term deterioration of the cavities. This paper describes a major breakthrough in the rock mechanics design of solution cavities which is the development and application of the REM computer simulation system. From the computer simulation analysis, the long-term deterioration process of cavities can be related to the basic parameters of rock mechanics design and the storage operations. The computer simulation system is also used for optimizing cavity design and operational specifications. This optimization technique is explained by its application to the three basic storage systems: 1) open dry storage system for liquids and solids 2) open wet storage system for liquids 3) pressurized storage system for gases, liquids and solids The effectiveness of the optimization technique is illustrated with some field examples by showing the direct interaction between the computer simulation system and field data of a test well including tectonic stress conditions, material property coefficients and geological anomalies.

Jan 1, 1974

By V. S. Znamensky, R. V. Stewart

This chrysotile asbestos ore body is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 miles) north of Montreal, 480 km (300 miles) north of the tree line, and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1% mile) in length, some 61 m (2OO ft) in width and plunges at 25o to 30 o below surface to a vertical depth of at least 610 m (2000 ft). The ore body was originally evaluated by programs of surface mapping, diamond drilling, and bulk sampling. The fiber is semicrude, possesses excellent strength, and good fiber length distribution. GEOLOGICAL SETTING, LOCATION, AND DISCOVERY The chrysotile asbestos mineralization at the Asbestos Hill mine occurs in serpentinized ultrabasic rocks of Precambrian age. These intrusive rocks are found in older volcanic sedimentary rocks known as the Cape Smith-Wakeham Bay belt and are shown in Fig. 1. The rocks comprising this belt overlie older basement rocks composed of granite and granite gneiss. This belt has a width of 32 to 64 km (20 to 40 miles), and trends in a general east- west direction, a distance of about 370 km (230 miles) from Wakeham Bay on the east coast of the Ungava Peninsula to Cape Smith, located on the east side of Hudson Bay. Two sequences of rock have been recognized in this belt. The lower (oldest) rocks are known as the Povungnituk group, and consist principally of massive lavas and sediments. The upper (younger) rocks are known as the Chukotat group, and are composed of pillowed lavas with interbedded sedimentary rocks. Sills of ultrabasic rocks exist in both younger and older rocks, but are more often found in the Povungnituk group. Concentrations of chrysotile asbestos, as well as nickel and copper minerals are found at or near the base of ultrabasic sills, and are most common where a change in dip occurs. The mine is situated about 1818 km (1130 miles) north of Montreal, approximately 1126 km (700 miles) north of the start of continuous permafrost, and about 482 km (300 miles) north of the tree line. The depth of permafrost at the mine site has been calculated to be approximately 549 m (1800 ft). This rich deposit of asbestos was discovered in 1957 during extensive exploration for nickel in the Ungava nickel belt. During that year, traverses conducted by Murray Watts spotted interesting looking ultrabasic rocks, and followup ground examination disclosed rich surface showings of asbestos mineralization near the present open pit. In 1958, a two-man prospecting party returned to the discovery site and a mineral exploration license was granted to Fig. 1. Location map Keewa Quebec Mines Ltd., a wholly owned

Jan 1, 1986

By Melvin W. Dadd

[One of the major problems in the purchase and sale of coal shipped in lake or ocean going vessels has always been the difficulty in obtaining a true analysis of the shipped coal?s quality because of faulty sampling by manual methods. As long as coal was sampled according to standards set up by ASTM methods designated D 492-48 there generally were no quarrels with the results obtained. However, due to varied weather conditions and because of the large number of cars sampled, there is no assurance that prescribed manual methods of sampling will always be followed. Because of this problem, the organization previously called American Coal Sales Association, now part of the National Coal Association, set up a committee compose of representatives from coal producers, coal shippers and coal consumers to study this sampling problem and to devise, if possible, a means of sampling on the high lift dumpers which could be automated so that a; true sample of the coal as loaded in the railroad car could be obtained.]

Jan 1, 1962

By L. George Imperato

The Blocked Iron Corporation has been active for many years in the development of mineral agglomeration processes by cold chemical induration. Millions of tons of iron ore fines agglomerated by their methods have been consumed in open hearth steel making furnaces. Some of you may remember these open hearth agglomerates as the carbonate-bonded cylindrical block shown in figure 1. With the realization that iron making would create the greatest demand for agglomerates our research efforts were directed to the production of carbonate- bonded (C-B) pellets containing iron ore, flux and carbon, shown in figure 2.

Jan 1, 1968