Search Documents

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

A worker’s personal exposure to respirable dust in occupational environments has traditionally been monitored using established methodologies which entail the collection of an 8-hour representative sample that is sent away for laboratory analysis. While these methods are very accurate, they only provide information on the average exposure during a specific time period, generally a worker’s shift. The availability of relatively inexpensive aerosol sensors can allow researchers and practitioners to generate real-time data with unprecedented spatial and temporal granularity. Low-cost dust monitors (LCDM) were developed and marketed for air pollution monitoring and are mostly being used to help communities understand their local and even hyper-local air quality. Most of these integrated sensing packages cost less than $300 per unit, in contrast to wearable or area dust monitors specifically built for mining applications which have been around for decades but still average around $5,000 each. At the National Institute for Occupational Safety and Health (NIOSH), we are leveraging the power of high-volume data collection from networks of LCDM to establish baseline respirable hazard levels and to monitor for changes on a seasonal basis as well as following any application of control technologies. We have seen the effective use and advantages of monitoring live data before, during, and after events like shift changes, operational changes, ventilation upgrades, adverse weather events, and machine maintenance. However, many factors have prevented a systematic adoption of LCDMs for exposure monitoring: concern for their analytical performance, the complexity of use, and lack of understanding of their value are some factors. This contribution outlines a one-year case study at a mine in Wisconsin USA, covering the installation, maintenance, data visualizations, and collaboration between NIOSH researchers and the industrial hygiene professionals at the mine.

Feb 1, 2024

Miners really are an optimistic bunch. Even with the dark clouds hanging over the global industry, mining professionals still turn out in droves at industry conferences. In February, more than 7,200 professionals attended SME?s Annual Meeting in Denver, CO, a record. And the following week, more than 30,000 people converged on Toronto, ON, Canada for the Prospectors and Developers Association of Canada (PDAC) meeting. For many small and junior mining and exploration companies the PDAC conference is a place to find potential investors in their projects. The Investors Exchange attracts several hundred companies, each showing off their properties to the many money types who wander the hall during the four-day conference.

Jan 1, 2013

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By H. Sevim

This paper identifies and formulates the probabilistic nature of underground coal face operations using the Semi-Markovian theory. Through this theory the probability of coal flow from a face is obtained for any given time t of a shift. These probabilities are used for determining the capacity and operating policy of a surge tank located at the shaft bottom.

Jan 1, 1984

By J. A. Botín

Investment decision for large mining projects imply an enormous financial risk and therefore, require a more complex risk evaluation methodology taking into account all sources of uncertainty from each process in the project value chain. Generally, the main sources of risk are those related to uncertainty on grade and other techical variables of the orebody. In this study, conditional simulation is applied to develop a risk management model to quantify and to manage financial risk associated to uncertainty on the grade of the orebody. The model was validated in case study on a real porphyry copper orebody in Chile.

Feb 23, 2014

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By Robert A. Westman

The INRED process has been developed step by step by Boliden since 1972 at MEFOS, the Foundation for Metallurgical Research, at Lulea in Sweden. The demonstration - plant is number five in this series. The purpose of this plant, which has a nominal capacity of 60,000 tonnes per year of hot metal is to: 1) prove the process on a sufficiently large scale to provide the basis for construction of production plants, 2) test various kinds of raw materials on behalf of licensees, 3) train operators of the first production plant, 4) develop the process further for special applications.

Jan 1, 1983

By M. H. Bolu

Since undergoing a major mill expansion in 1979, Canada Tungsten Mining Corporation Limited has successfully operated a somewhat unconventional rod mill/rod mill grinding circuit at its mill in Tungsten, N.W.T., Canada. The concentrator employs two rod mills in series, of unmatched size and horsepower, for production of feed to a gravity (tabling) circuit. Cyclones and screens are closed circuited with the secondary rod mill. Outlined in this paper are the rationale behind, and consequences of operation of this unusual grinding and classification configuration.

Jan 1, 1984

By Jr. Koch

Since 1882, world zinc production has increased. In contrast, United States zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the United States, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in United States production are due to economic, not geological, factors. Recent exploration has located large mineable ore bodies; additional deposits will undoubtedly be found in the strata-bound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the United States is in an early stage of the production cycle for zinc. Of major mining districts in the United States, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district.

Jan 1, 1980

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By Mitchell Gordon

Two mineral processing facilities in North America required near terminal density slurries to perform de-bottle necking in their circuits. The installation at Barrick Goldstrike to ensure efficient oxidation conditions and throughputs in the refractory ore treating autoclaves. The Kidd Metallurgical Division unit to provide a steeper tailings slope to extend the life of the existing tailings dam. To achieve these goals, both operations selected a Supaflo "High Compression" Thickener following on site pilot plant evaluation. Commissioning and the first year of operation is reviewed. Operating data is compared with the pilot plant data. In particular, unusual doughnut formation at Goldstrike and the effect of temperature on the terminal density at Kidd Metallurgical Division are discussed.

Jan 1, 1997

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By G. Jim Cardwell

The question "what constituents should be determined?" is one that defies a simple answer, because earth scientist being what you are, the rock and mineral analyst will eventually be called upon to determine about three quarters of the elements in the periodic table. The concentrations of these analyses will range from as low as 1 ppb to 100% of the material being analyzed. The most important thing to remember about a quantitative analytical result is that it can only be an estimate of the concentration of the analyte present. A measure of the reliability of that estimate is given by statistically derived statements of the precision and accuracy of the measurement. When evaluating your data an understanding of precision and accuracy are of paramount importance. Precision is the measure of agreement between replicate values while the accuracy of a determination is the concordance between it and the true value. There is no quarantee, however, that a precise answer is an accurate one. The numerical difference between the two values is the error. When evaluating your data, the repeats analyzed with your samples will identify the precision and control standards of U.S.G.S. or Canadian Certified Materials quality will identify the accuracy. The main problem is this data is routinely withheld from the report, or was it ever included in the analysis of your samples?

Jan 1, 1983

By Alan S. Peck

Chemisorbed oleate films on the surfaces of fluorite, barite, and calcite were studied by means of infrared spectrophotometry. Evidence is presented which indicates the mineral anions, i.e., fluoride, sulfate, and carbonate, are displaced from the mineral surfaces as a result of the adsorption from aqueous solutions. Also, chemisorption reactions between oleic acid and fluorite or calcite occurred spontaneously in the absence of water. Carbon dioxide was identified as a reaction product when dry calcite was contacted with oleic acid. There was no evidence of reaction between oleic acid and barite in the absence of water.

Jan 1, 1964

By Pengfei Wang, Guorui Feng, Shufeng Zhang, Yuxia Guo, Tingye Qi, Dian Li

"Based on the geological conditions of the No. 10203 mining face of the Xinyang coal mine, a numerical model of the longwall backfilling face is built using the FLAC3D software to calculate the limit broken length of the key strata. Based on the deformation laws of the immediate roof, the backfilling parameters are determined. Furthermore, the movement laws of the overburden strata with different volume filling rates (0, 40, 60, 100, and 100%) and with different layout forms of the filling strip (under a volume filling rate of 60%) are analyzed. The results of the numerical modeling show that the stress of the two sides of the working face and the deformation of the overlying rock are gradually reduced with the increment of the volume filling ratio. In view of the deformation of the roof strata within the allowable range, a volume filling rate of 60% is selected to simulate and analyze the filling effect under different layout forms of the filling strip. The filling width, stress concentration area, and layout form of the filling strip are the key factors to control the movement of the overlying strata. In addition, the probability integral formula is used to calculate and predict the ground subsidence on the filling area, which confirmed that the backfilling mining method is fully applicable in the Xinyang coal mine. The results of this study provide a certain theoretical basis for the determination of the filling process in the field.INTRODUCTIONIn China and other coal producing countries, gob is managed using the caving, filling, supporting, and slowly sinking methods (Zhang, Zhou, and Zhang, 2009). With the continuing development of the concept of green coal mining (Guo, Deng, and Zou, 2004), the filling method, which is safe and environmentally friendly, has been widely used in the field. On one hand, this method could reduce waste rock and other waste discharge. On the other hand, it could effectively slow the surface subsidence. Recently, strip-filling mining mostly adapted the arrangement of the strip backfill with equal intervals and widths (Xie et al., 2004), but the reasonability of this arrangement should be discussed. To arrange the intervals and width of the strip-filling body reasonably, Feng et al. (2019) put forward the “constructional backfill mining (CBM)” concept. The CBM is a type of backfill mining with low backfill rate, strong structural stability, and good backfill effect. The targets of the CBM include the efficient usage of solid waste resources in mining areas to reduce the backfill cost, the improvement of backfill materials and backfill technologies to increase the backfill efficiency, and rational planning of backfill and mining scheme to reuse the underground mining space. The determination of proper width and intervals for the strip-filling body is the main content of the CBM. Strip-filling mining using cemented coal gangue backfilling is the main method to undertake overburden of the overlying strata and to slow down the surface deformation. It also plays an effective role in cost reduction (Xu et al., 2007). This study focuses on proper determination of the strip-filling body parameters according to actual geological conditions by a simulation. It provides an appropriate reference for backfill mining in the Xinyang coal mine."

Jan 1, 2019

By Y. J. Son, S. S. Nageshwaraniyer, K. M. Kim

"This paper reports on the development of a simulation-based framework for obtaining optimal blast design parameters for a hard-rock mine. To do this, a conventional medium-sized hard-rock mine was taken as a case study. The mine has two pits containing hard and soft rock types. The proposed framework contains a combination of regression analysis using Excel software by Microsoft and discrete-event simulation using Arena software by Rockwell Automation, applied to construct a model of the material-handling network of the mine. Specifically, blasting parameters are estimated by Excel-based regression analysis, processes including blasting and haulage from pits to crushers are modeled by a Forward Blasting simulation submodel, and material-handling operations including crushing, storage in stockpile, and haulage via conveyors and into SAG and ball mills are modeled by a Crusher to Ball Mill simulation submodel. A Reverse Blasting submodel is then used to obtain the optimum blast design corresponding to a target P80 particle size. Using the proposed framework, an economic analysis was performed to demonstrate the cost savings that could be realized for each rock type as a function of specific explosive energy. IntroductionIn a modern hard-rock mine, various processes such as drilling, blasting, crushing, grinding and mineral liberation are optimized to increase productivity, a practice known as mine-to-mill (MTM) optimization. Blasting is important in MTM optimization as it is the first comminution process and has an impact on all downstream processes (Julius Kruttschnitt Mineral Research Centre, 1996; Nielsen and Lownds, 1997; Nielsen and Malvik, 1999; Chung and Katsabanis, 2000; Kim and Kemeny, 2011a; Kim and Kemeny, 2011b).Two main research topics have emerged in the area of blasting design: (1) identifying the optimal target blast fragmentation at each shot and (2) controlling the blast fragmentation for that target. As part of an MTM optimization study, Kim and Kemeny (2011a; 2011b) developed a site-specific blast fragmentation prediction model that can be used to identify the target blast fragmentation and can be incorporated into MTM optimization. They also reported methodology for assigning model parameters easily and with minimal human bias."

Jan 1, 2015

By Rodolfo V. de la Cruz

This paper describes the development of a new method and device for determining the in-situ mechanical properties of rock masses. The method involves a self-recording mechanical deformation gauge for sensing-recording she deformation of the borehole wall when loaded hydraulically. The self-recording feature of the gauge eliminates the difficult technical problem of transmitting signals over very long cables for measurements at great depths. Adopting a mechanical gauge instead of electronic, electrical, optical or grid techniques eliminates delicate instrumentation and installation problems. Moreover, mechanical gauges are inherently rugged and suitable for use in severe borehole conditions including very high temperatures. The technique was tested in limestone, basalt and granite specimen. The calculated mechanical property values for 1 the tests agree with those obtained by conventional testing methods. The self-recording mechanical deformation gauge has a minimum reading of 50 micro inches (1.27 x 10-3mm), comparable with electrical resistance strain gauges, capable of reading deformations over a range of 0.25 inches (6.35mm). The sensitivity, ease and accuracy of the method recommends it highly for in-situ rock modulus measurements.

Jan 1, 1980

By Volkmar Niemitz

Approximately 30 miles east of Chicago on the southern shores of Lake Michigan stands Bethlehem Steel's newest fully integrated steelmaking facility - the billion dollar Burns Harbor plant. The initial phase of "green field" construction that began in 1963 was directed to the creation of high quality finishing facilities. In late 1964 the 160" plate mill came "on stream" followed closely by Sheet and Tin and Hot Strip facilities. Unit train shipments of slabs primarily from the Lackawanna plant located near Buffalo constituted the input materials for the new mills. In 1967 a hot metal facilities program was announced for Burns Harbor that at its completion would make the plant fully integrated. Incorporated within the program were: 1. A new high performance 50" x 96" slabbing mill complete with a battery of soaking pits. 2. A two vessel Basic Oxygen Furnace Shop. 3. (1) battery of 6 meter high Coke Ovens with attendant coal handling facilities. 4. A 3800 feet long vessel loading & unloading dock. 5. The first conveyor belt fed Blast Furnace in the United States. 6. An extensive materials handling system for receiving, stocking and reclaiming from storage the raw materials for the Blast Furnace and Coke Ovens operation. The intent of this paper is to provide a detailed description of the functions and components of the materials handling system noted above.

Jan 1, 1970