Search Documents

By P. C. Miller

The paper reports laboratory results from the bioleaching of chalcopyrite ores and concentrates using a mixed moderate thermophile culture. Copper dissolution in excess of 95% was achieved in all cases with the majority of tests indicating copper dissolution in excess of 98%. Aspects of downstream processing are discussed in relation to iron rejection by precipitation. The laboratory results indicate the need for careful control of the pH value to prevent co-precipitation of the copper with iron. A comparison of capital and operating costs is given indicating potential differences between the use of toll smelting and bacterial leaching on site. A discussion is given highlighting the sensitive cost areas of these two process routes.

Jan 1, 1997

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By Baolin Qu, Jingxin Wang, Cuncang Xu, Bing Wu, Mingyu Zhong

With the development of the coal mine regulation regime, the situation of coal mine safety production in China has continued to improve. However, coal mine accidents have not been fundamentally eliminated; constantly learning from historical accidents can make mining work safer. Therefore, to better understand the coal mine accident characteristics, this study analyzes the tendency of coal mine safety accidents from multiple perspectives, among which all accidents after the establishment of the State Administration of Coal Mine Safety in 1999 are the top priority. The results show that strict national policy, technological progress, and reasonable coal prices are conducive to the safe development of mines. On the contrary, high-intensity centralized production will lead to frequent accidents in the peak season of coal production. In addition, the type of coal mine ownership will have an indirect impact on the occurrence of coal mine accidents. The research results not only play a positive role in the prevention and control of coal mine accidents in China but also have reference meanings for the safety production of coal mines in other countries in the world.

Dec 28, 2022

By S. P. Fleming

An acid mine drainage sludge containing 0.26% nickel, 0.21 % cobalt and 4.5% manganese was leached in a one-liter reactor with sulfuric acid in the absence and presence of sodium sulfite. The effects of temperature (25°C and 52°C) and sodium sulfite concentration (up to 0.03 molar) on the leaching rate were particularly investigated. The leaching rates of nickel and cobalt with sulfuric acid have been determined to be controlled by diffusion through product layer. It has been found that effective leaching conditions to give more than 90% extraction of nickel, cobalt and manganese while keeping the iron extraction below 10% come with an elevated temperature and a low sodium sulfite concentration at pH 3; for example, 52°C and 0.01 molar sodium sulfite.

Jan 1, 1992

By M Aboagye, K Appau, W. Assibey-Bonsu, C. Muller

A case study based on two recoverable resource modelling techniques (indirect and direct or localised methods) have been derived using typical feasibility study or new mine drilling data configurations from the extensions of an existing mine’s massive production database. The database is from the Gold Fields Tarkwa Gold mine (~6Moz Mineral Reserves and 13-year Life-of mine). The corresponding recoverable resources from the various techniques are then analysed using the open pit Whittle optimisation process. The results were then compared based on the Whittle optimisation results to determine the efficiencies of the approaches and the validity of the recoverable mineral resource estimates for mine planning and financial forecasts (including Cash Flows etc). Based on historical production metal recovery, the paper also assesses the corresponding orebody and mine planning as well as financial risks with regards to the modelling techniques. The study shows that the localized direct and somewhat more straight forward approach if applied efficiently can provide an equally useful tool for computing recoverable resources for mine planning and financial forecasts, as compared to the indirect approach as presently in use.

Jun 25, 2023

By James W. Clark

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1984

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By Q. Xu

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactant was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1991

By L. R. Todd

Gold Fields' Mesquite mine, located in southeastern California, heap leaches low grade gold ore at an annual rate of 2.7 Mt (3 million st). Ore is crushed in a two stage open circuit and belt agglomerated prior to loading on the leach pads. Since initial heap construction in October of 1985, a number of operating practices have been modified and several agglomeration techniques have been tested in an effort to improve percolation and reduce leaching time. Findings to date are discussed.

Jan 1, 1987

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By L. Cui

A new flotation collector, benzyl arsonic acid, was used for the flotation of ilmenite. ESCA, Auger spectroscopy, and chemical analysis were used to investigate the correlation between the variation in surface constituents and the flotation recovery of ilmenite. Experiments indicated that, as the ratio of surface Ti ions/surface Fe ions increases, flotation recovery increases. pH regulation with an inorganic acid was found to be effective in changing the ratio of surface ions, and, hence, the flotation recovery.

Jan 1, 1986

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Howard E. Mitchell

Modern mechanical raise drilling was first introduced into the United states in 1962. This method of safely, economically raising a shaft has steadily increased in popularity since that time. This steady growth has been largely enhanced by the many advantages to be gained by mechanical raise drilling, as well as by the increasing reliability of the equipment required. It is the purpose of this paper to briefly review the state of the art of raise drilling to include: the various applications and advantages; the equipment requirements, including a comparison of the various types and sizes of machines and rock cutting equipment; equipment performance; and future trends.

Jan 1, 1978

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

The 31st annual American Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Tucson Starr Pass Resort on Saturday, Dec. 7, 2013. Each year, one living inductee, two Medal of Merit recipients, honorees from mining?s past, an industry partnership award, as well as a special citation, are recognized by the MFSW for their respective contributions to the mining industry. James D. Toole, past president and chief executive officer of Southwest Energy LLC, will be the Hall of Fame inductee, guest of honor, and featured speaker at the awards banquet. Toole founded Southwest Energy LLC in 1973 and is credited with introducing innovative explosive technology, providing even greater value to its mining customers. Medals of Merit will be awarded to Joseph M. Keane, principal metallurgical engineer for SGS Metcon Research/KD Engineering, and Sean D. Dessureault, associate professor at the University of Arizona. Keane is recognized for his metallurgical expertise, especially in design development and pollution abatement. Dessureault is recognized for his advanced mining research, with more than 25 journal publications, and his entrepreneurship as the founder and chief executive officer of two mineral-related companies. To honor mining?s past, the hall of fame will induct Bartolomé de Medina for his invention of the patio process for recovering silver; Ben Williams for his management of the Copper Queen Mine in Bisbee, AZ; Charles E. Mills for his contributions at Morenci and Inspiration Copper and founding Apache Powder Co. and The Valley National Bank; John S. Finlay and Edwin B. Royle for their invention of the mucking machine; and Louis Caryl Graton for his ore deposits research and teaching economic geology at Harvard University.

Nov 1, 2013

By Charles E. Stack

There are several ways in which to classify refractories. The most suitable one is based on their general composition or raw material content. The categories are: 1. Aluminosilicate brick which include the fire clays and alumina and high alumina raw materials. 2. Basic brick which includes magnesia and chrome ore alone and in various combinations. 3. Silica brick which uses gannister or high purity gravels and sands. 4. Insulating brick are generally of the aluminosilicate type but may be most all refractory raw materials. 5. Special refractories are made from raw materials of zircon, zirconia, ultra high alumina, silicon carbide, fusion cast products, chromic oxide, carbon and graphite. The raw materials that make up these different categories are what we are briefly going to consider. Emphasis is placed more on the most important raw materials.

Jan 1, 1976