Search Documents

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

By Raymond K. Will

Computers are becoming increasingly valuable tools in the mining industry as a greater variety of appropriate hardware and software becomes available, combined with greater acceptance by management, Within a given time period an engineering staff can evaluate or design a project to much greater detail and higher accuracy by utilizing computers once suitable programs have been developed. We are all aware that throughout the world the decreasing grade of minerals coupled with increasing waste to ore ratios necessitate larger capacity, longer term mining operations and attendant higher capital costs. Computers can be of assistance in all stages of mineral exploitation, from geologic exploration through mine feasibility studies and design, to marketing and transportation. Because of the high speed with which data can be digested and manipulated by computers, preliminary information from any stage of investigation can be analyzed to assist in further guidance of that stage. By use of preliminary mine feasibility studies, financial forecasts and sensitivity analysis, even information from a far-removed phase such as marine transportation of the product, can help guide the exploration phase to a realistic target.

Jan 1, 1973

By S. G. Ozkan

Boron minerals of economic importance are primarily colemanite, tincal, and ulexite. Turkey and the United States are the leading producers of boron minerals and compounds. Other production includes datolite in Russia and synthetic colemanite in Chile. This paper will discuss various types of chemical and physical treatments of boron ores to produce the marketable minerals and compounds that are consumed in commercial products.

Jan 1, 1995

"Controlling dust generation and keeping it below permissible limits at the working face of a room and pillar mine is a challenge for mine operators. With the recent changes in the respirable-dust regulation, it has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) stated that a flooded-bed scrubber, under its optimum condition, can achieve cleaning efficiencies between 58 and 90 percent. The performance of such a system can be maintenance intensive. Other industries face similar dust control issues. The University of Kentucky partnered with Toyota Motor Manufacturing for the development of a novel wet scrubber for capturing paint overspray, with capture efficiencies in excess of 98 percent and minimal maintenance. The aim of this study is to assess the ability of this novel wet scrubber to capture respirable dust in an underground coal mine. This paper presents the conceptual design and the computational fluid dynamics (CFD) modeling of this novel wet scrubber. It discusses the results of the CFD simulation performed on the novel wet dust scrubber. INTRODUCTION Dust generation from underground coal mining is an inescapable phenomenon. No matter the practices employed, it inevitably occurs. Elevated concentrations of coal dust are potential health and safety hazards. Although dust in an underground coal mine cannot be completely avoided, its influence can be mitigated through good engineering practices. The effect of dust on the health of mining personnel has had a significant impact. The prolonged exposure of airborne respirable dust (< 5 µm) can cause coal workers’ pneumoconiosis (CWP), silicosis, emphysema, and chronic bronchitis, collectively known as black lung (U.S. Department of Labor, 2014). According to the National Institute for Occupational Safety and Health, black lung has killed more than 10,000 miners between 1995 and 2004 (NIOSH, 2008). In addition to being a health issue, coal dust is also a safety issue to the underground coal miners. The generated dust, if not captured, is dispersed into the mine air through the ventilating air and deposited downwind on the return entries’ surfaces. In the event of a methane explosion, the coal dust, if insufficiently diluted with rock dust, triggers a coal dust explosion which is much more severe than a methane explosion and causes more damage (Kenneth et al, 2006). The Jim Walters No. 5 Mine and the Upper Big Branch Mine disasters which together killed 42 people and resulted in damage worth millions of dollars in property are the examples of coal dust explosions (U.S. Department of Labor, 2001 & 2010)."

Jan 1, 2016

By D. L. McCain

In considering slurry transportation for Consolidation Coal Company&apos;s Loveridge Mine in Northern West Virginia, many things were taken into account. The advantages of slurry transportation in comparison to shuttle car, belt and rail transport have been given in previous publications." These include increased safety and the potential for increased productivity. In addition to these considerations, the slurry transport system installed in an existing mine provides an alternate or additional transportation mode to the one already existing. In the Loveridge Mine, this is rail haulage. Since the rail system is a single track system and the distances involved are several kilometers, it is not always possible to provide for haulage of loaded cars, return of empties, supplies and maintenance in an efficient manner. Slurry transport of the coal from the production faces to the preparation plant allows the rail system to fulfill the remaining transportation needs in an efficient manner. Consol initiated development work in slurry transportation in the early fifties leading to the construction and operation of the 174-km (108-mile) Cadiz-to-Cleveland pipeline which carried 1,200,000 metric t/y (1,300,000 t/y) from 1957 to 1963. Development work on coarse coal slurry transportation for underground mines started in 1970 with feasibility tests on coarse coal at Conoco&apos;s Ponca City, Oklahoma, slurry test facility. A series of tests were conducted in several locations as development work proceeded on the various subsystems, mechanical equipment and controls required to produce a working system to follow a continuous miner in a room-and-pillar type mine, then to combine the coal production from several mine faces for mainline transportation to the preparation plant. The face system, including the crusher-pump vehicle, hose hauler vehicle, slurry booster pump units, return water unit and 900 to 1,200 m (3,000 to 4,000 feet) of pipeline was brought together for the first time and tested as a system at Consol&apos;s Robinson Run Mine in northern West Virginia in 1975. A pipeline wear test at the Loveridge Mine where 300,000 tonnes (330,000 tons) of minus 127-mm (5-inch) run-of-mine coal were pumped from the raw coal bin into the preparation plant and a large scale test in Ponca City on a multiple feed sump where several slurry flows could be combined to provide surge capacity and a constant reclaim rate for mainline transportation completed the preliminary testing for a complete system. A decision was made to commit the system to a mine, and the south half of the Loveridge Mine was chosen. This site required the transporting of coal from one longwall and two continuous miner development faces. To prevent startup and unexpected problems in the slurry system from shutting down production of coal from the longwall face, the rail car loading point from the main section belt was chosen as the feed point for the slurry system and the design would allow for rapidly switching from one transport mode to the other. Scheduling of required development entry work and the developmental nature of the system led to a decision to install only one continuous miner face slurry transport system rather than two for this first system. The type of continuous miner in use at the mine for the foreseeable future was the Joy 2BT6 twin boring machine. This machine cuts a stable, arch-shaped entry and was therefore allowed to mine about 26 m (85 feet) of entry before roof bolting was re¬quired. Since peak production from this type of machine was not high, a smaller transport system could be used with it.

Jan 1, 1981

By F. Milton Lewis

In 1977 a paper was presented which reviewed the cost trends in producing copper by conventional processes for five years, 1972 through 1976. In this paper these costs have been updated to include the years 1977 and 1978.

Jan 1, 1979

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation&apos;s energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By J. P. Gliddon, G. C. Wade, J. W. Lill

Since 1980 a number of significant changes have been introduced at Palabora in an effort to offset the effects of reduced product price and increased unit costs of production. These changes and improvements include major equipment rationalization programs, the introduction of trolley-assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives, and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation, and their contribution to cost reduction and improved productivity at Paihbora are considered.

Jan 1, 1987

By M. M. Rajkovich, J. J. Zaluski, S. J. Gardner

The telephone rings at 3:20 a.m. and an exasperated voice on the other end says, “There’s been a mine explosion at Mine No. 5 and we have not heard from three units of men!” Twenty-three minutes later, the phone rings again and another panicked voice says, “There’s something wrong at the slurry impoundment, the pool level has just dropped five feet and we’re trying to figure out what’s wrong!” Thirty minutes later, the mobile phone rings and an excited security guard says, “We have reports of thick black water running down both the right fork and left fork of Straight Creek and both seem to be rising in the banks!” As if this isn’t enough excitement, the mobile phone rings again and a stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Company No. 2 Mine, which is adjacent to our No. 5 Mine!” Is this all some kind of dream or nightmare? More importantly, however, if this could happen, what on earth do you do? Although we all like to think that “It can’t happen to me,” we all must admit that mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. Your response must be quick, cool-headed, calculated and effective. This paper will examine the issues, concerns and ramifications of this hypothetical “disaster” and then present a systematic crisis management response. While each situation is different, there are general guidelines for forming an effective plan of action.

Jan 1, 2003

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Company to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the Company&apos;s main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received substantial attention in recent years. A Company guideline that no coal shipment shall exceed any contract or company-imposed coal quality specification has been successfully implemented. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed. Background Surface coal mining of subbituminous C rank coal in the Cillette. (Campbell County) Wyoming area has become increasingly competitive during recent years. Prior to 1974, one small surface mine produced coal for local consumption. During the last ten years, 13 new surface coal mines have been constructed. Coal production from Campbell County, Wyoming totalled 88 million short tons (79.8 million metric tons) in 1983, the majority being shipped to electric utilities in the central and southern United States via unit trains having a capacity of 10,000 short tons (9,072 metric tons).

Jan 1, 1984

By A. G. Oppegaard

Most iron ores treated by the R-N direct reduction process yield metallic iron products considerably lower in titanium, manganese, and chromium oxides and alkaline metal sulfates/sulfides than were contained in the original ores. These metallic iron products are suitable as feed stock for the open hearth and electric steel-making furnaces. The elements which are rejected in part are acceptable in the product since the product is designed to by-pass the blast furnace. R-N reduction conditions (PCO+H2-1 atmosphere, 1830° to 2150° F.) are adjusted for each ore. The iron ore which is reduced to 90 to 95 percent metallic iron is then subjected to the conventional beneficiation techniques. Under these conditions, 55 to 80 percent of titanium oxides, 75 to 95 percent of manganese oxides, 60 to 90 percent of chromium oxides and up to 97 percent of alkaline metal sulfates contained in the ore are rejected with the gangue to the non- magnetic tailings. The metallic iron products illustrated in this work contained 89 to 96 percent total iron, one to five percent TiO2, 0.2 to one percent MnO, 0.3 to 1.6 percent Cr2O3 and/or up to one percent alkaline metal sulfide. Usually only one of these components was present. Recoveries ranged from 80 to 96 percent of the iron in ore.

Jan 1, 1958

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond&apos;s work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984