Search Documents

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation's energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By J. P. Gliddon, G. C. Wade, J. W. Lill

Since 1980 a number of significant changes have been introduced at Palabora in an effort to offset the effects of reduced product price and increased unit costs of production. These changes and improvements include major equipment rationalization programs, the introduction of trolley-assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives, and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation, and their contribution to cost reduction and improved productivity at Paihbora are considered.

Jan 1, 1987

By J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Company to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the Company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received substantial attention in recent years. A Company guideline that no coal shipment shall exceed any contract or company-imposed coal quality specification has been successfully implemented. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed. Background Surface coal mining of subbituminous C rank coal in the Cillette. (Campbell County) Wyoming area has become increasingly competitive during recent years. Prior to 1974, one small surface mine produced coal for local consumption. During the last ten years, 13 new surface coal mines have been constructed. Coal production from Campbell County, Wyoming totalled 88 million short tons (79.8 million metric tons) in 1983, the majority being shipped to electric utilities in the central and southern United States via unit trains having a capacity of 10,000 short tons (9,072 metric tons).

Jan 1, 1984

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond's work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Esko O. Nermes

Outokumpu flash smelting of copper concentrates was introduced in 1949 and flash smelting of nickel concentrates in 1959, both at Harjavalta in southwest Finland. The first flash smelter outside Finland was started up in 1956 in Ashio, Japan. Between 1956 and the present about 25 flash smelters for copper, and nickel concentrates have been put into operation in different parts of the world. Outokumpu"s research organization has been highly involved in the development of flash smelting. For example, a direct blister flash smelting process was developed in 1975 and introduced in Glogów, Poland, in 1978, and another has been designed for Zaire. This straight metal process is based on low iron content of the concentrate, which reduces the amount of recycling slag copper. Additionally, the concentrates are rather low in impurities.

Jan 1, 1982

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By R. J. Visintainer, J. M. Furlan

"Due to the time-consuming nature of froth testing in a laboratory environment, practical limitations require the development of a method of applying a single set of performance test data (Visintainer and Whitlock, 2012) obtained for a single froth pump at a given speed to a range of froth pump speeds and sizes, % air content and liquid viscosities. Head, efficiency and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique that can be used to interpolate from existing test data in order to predict froth performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal, as well as the insights gained from analysis of the resulting regressions, are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute standard for the effects of liquid viscosity on centrifugal pump performance (ANSI, 2010).IntroductionPump performance data (Visintainer and Whitlock, 2012) has been collected for a froth pump using an experimental loop outfitted with an array of pressure transducers, mass flow meters, an inverted U-loop, magnetic flow meter and an assortment of other instrumentation. Experiments were performed on pure water, water and air, pure corn syrup, and corn syrup and air. Data was obtained for % air contents of 0-30% and viscosities of 1- 15,000 cSt at eight specific valve positions (eight different flows as a percentage of best efficiency flow points) and the viscosity was changed by allowing the system temperature to increase during testing. The test pump is a 710-mm diameter impeller, GIW HVF, open shrouded, vented design that has its discharge axis oriented at 45° upward from the horizontal. A schematic diagram of the froth pump test loop can be seen in Fig. 1."

Jan 1, 2015

By Nord L. Gale

The discovery of important new ore deposits of lead, zinc, copper and silver in 1955 in Southeastern Missouri has resulted in the development of a thriving mineral industry known as the "New Lead Belt" or "Viburnum Trend", to distinguish it from the older lead producing areas to the East. This region has recently become the world's largest lead producing district with production in 1970 reaching 432,576 tons or 74.4% of the entire United States lead mine production. The area is heavily forested with rolling hills dotted with numerous clear running streams in the Clark National Forest of the Missouri Ozarks. The location is within 70 miles of St. Louis, Missouri and has a natural abundance of water resources which provide an important recreational area for fishing, hunting, camping and other outdoor activities. Until this recent development, the area was sparsely populated and industrialization was almost unknown. The infusion of $150 million in mining capital has brought about a dramatic change in the economic structure of the area and will almost surely be accompanied by changes in its environmental picture. In an effort to maintain this bountiful national resource and to evaluate the changes occurring in surface water quality and aquatic life forms present, an inter- disciplinary research program at the University of Missouri has been undertaken with the support of the National Science Foundation. Research has been carried out to determine background values, establish natural baselines, and to evaluate the extent and causes of changes in streams effected by mine water discharges and wastewater from ore milling operations. The unique topography of the "New Lead Belt" area allows the channelization of milling and smelter wastes to separate stream systems (Figure No. 1) thus allowing measurements of the pollutional effects on an individual basis.

Jan 1, 1973

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By R. A. Lowe

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determines whether the clay can be utilized for paper and ceramic applications. In this work, causes of poor low-shear viscosity and methods of improving rheology have been investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 1998

By Emanuele Catelli, Paolo Vicentini, Manuel Petitat, Paolo Lanfranchi

"More than 800 million tons of material will be excavated during large underground projects such as tunnels, undergrounds and power plants by 2030 in Europe only. The raw material excavated is often classified as waste, which involves environmental impact and transport issues: landfill areas, CO2 emissions and noise. But how can such massive amounts of material be transported, processed and deposited? Using the example of the AlpTransit Ceneri Base Tunnel (15.4 km), we show that suitable excavated materials can be used sustainably as a primary resource for tunnel concrete. This requires careful planning of the installations and storage areas by the client, timely building of the processing plants and other handling facilities outside the tunnel and a continuous evaluation of the raw material quality. 1. INTRODUCTION Spoil management is a central element of large construction projects. The systematic reuse of suitable excavated material not only saves natural resources, reduces transport distances and landfill volume, but can also decrease overall construction costs. Ideally, all of the concrete needed for tunnel lining can be produced with this on-site material. Such a natural resource management concept was applied for the construction of the new Gotthard Base Tunnel (L = 57 km). Spoil management concepts are, how-ever, difficult to implement and call for innovative techniques, sophisticated logistics and organization. In the context of large projects, environmentally friendly transport, processing and storage of millions of tons of excavated loose material represent another logistics challenge (Simmen & Lieb, 2010). This paper shows key factors that led to the successful completion of spoil management at the Ceneri Base Tunnel, which constitutes a part of the AlpTransit Gotthard Project (Figure 1)."

Jan 1, 2016