Search Documents

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By E. Sirolli

In recent times, with rare exceptions, most economically viable ore discoveries have been large, low-grade and located in remote parts of the world. Mining companies have often shown to be incapable of mitigating their social and economic impact on local communities. Sustainable development and relations can be achieved by implementing bottom-up methodologies to the top-down tools already in use by mining companies. In order to magnify the importance of enterprise facilitation as a primary method for community development, data from 25 years of community based work around the world was used. Results highlight the need for a grassroots approach to local economic and community development, which focuses on the creation of a parallel economy in communities. Using solely top-down methodologies for developing community relations is shown to be a limited resource for mining companies. There are fundamentally two dangers for mining companies: alienating the local population, resulting in militancy and lengthy legal battles to obtain a license to operate; and, being accountable for building social and economic infrastructure that are not the company?s responsibility.

Jan 1, 2012

By W. M. Cross

Optical fibers have revolutionized the telecommunication industry, because of their ability to transmit large amounts of data over long distances. Without optical fibers many of the communication technologies on which business, industry and research rely would be impossible. In addition to their use as communication devices, optical fibers are often used as sensors. Despite the great promise that optical fibers have for the development of many types of remote sensing devices, few remote sensing devices have been built for use in the mineral industries. This paper will describe the use of optical fibers as sensors for surfactant adsorption at mineral surfaces.

Jan 1, 1995

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By T. Lee

Ongoing economic success for mining companies is dramatically enhanced when they really know what they are harvesting, such that they can accurately forecast their head grades for any time period in excess of a month. This is an uncommon experience. It is a very common scenario for resource/reserve estimates to overstate the concentration (grade). Grade is a critical input of revenue, and hence, it is to cashflow projections. With the current direction being taken by the legal climate, it is no longer adequate for directors to accept the resource/reserve estimates of experts at face value. This is because resource/reserve estimates are the foundation of primary mineral economic decisions. Directors of mining assets need to undertake their own due diligence analysis of these estimates, in the best interest of themselves, and the company's shareholders. In the light of the industry's past achievements, this is quite a challenge. This paper suggests a set of new objective tools for directors to undertake an overview of the unique commodity concentration pattern and assess associated economic dynamics of each mineralization. These tools allow the examination of global graphical trends that can be helpful to directors and others in undertaking due diligence of resource/reserve statements. Ensure that it smells right.

Jan 1, 1995

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By S. A. Pirzada

A thermal plasma assisted laminar flow reactor has been used to evaluate the kinetics of converting alumina to sodium aluminate in flight. Free energy minimization calculations were used to determine experimental conditions. The experimental variables include: alumina particle size, alumina/sodium nitrate molar ratio, temperature and residence time. A mathematical model for the conversion was developed and validated. Experimental and mathematical results are presented.

Jan 1, 1996

By T. Negeri

Flotation is the most efficient and preferred solid-solid separation method in mineral processing. However, enhanced production of high-grade concentrates at sufficiently high recovery still poses technological challenges to-day. A novel flotation method to produce final-grade concentrates from finely-ground ores in a single step is being developed and tested by CANMET. For the complex sulphide ores tested, grades are superior while recovery is considerably improved. Furthermore, concentrate production rates, at similar recoveries, are faster than for the conventional rougher-scavenger-cleaner configuration. This paper discusses the physical operating parameters affecting Cu-Zn flotation metallurgy.

Jan 1, 1995

By C. E. Chapin

The Hansen orebody is a large (1 2 million kg U3O8, 0.08% U3O8 average grade) sandstone-type uranium deposit in the Eocene Echo Park Formation of central Colorado. The deposit occurs in carbonaceous braided-stream sandstones that are part of a wet-alluvial-fan complex that prograded eastward across a narrow strike-slip basin. The Echo Park basin is one of a series of basins that formed along the east side of the Colorado Plateau as it was translated northward during the Eocene culmination of the Laramide orogeny. The valleys of east- and southeast- flowing perennial streams, whose courses were transected by the subsiding Echo Park basin, were filled with permeable volcanic and sedimentary rocks during construction of the Oligocene Thirtynine Mile volcanic field. These paleovalleys funneled large volumes of uranium-bearing ground waters through the braided-stream facies of the wet alluvial fan. Uplift of a basement horst downfan from the Hansen orebody reduced transmissivity and helped maintain a reducing environment in the Hansen area; this later became an important factor in preservation of the Hansen orebody. The horst also deflected uranium- bearing ground waters upward into the Oligocene Tallahassee Creek Conglomerate where they formed the Picnic Tree orebody (1.1 million kg U3O8, 0.09% U3O8 average grade) in an altered ash-fall tuff that is essentially barren above the Hansen orebody. Several potential source rocks for uranium are present and range in age from Proterozoic quartz monzonites of Silver Plume age to lower and upper Oligocene ash-flow and ash-fall tuffs. Uranium may have been contributed to the Hansen orebody several times from different sources. Uranium and thorium analyses of ash-flow tuffs indicate that ample uranium was released during cooling and ground-water leaching to form several Hansen orebodies. The host sandstones are conspicuously altered, and their initial high permeability has been greatly reduced by precipitation of intergranular cements, especially clays and opal C-T. The alteration and cementation mineral assemblages and the chemical composition of stagnant ground waters recovered from pump tests indicate that uranium deposition occurred under alkaline, reducing conditions preceded and/or accompanied by bacterial production of framboidal pyrite.

Jan 1, 2013

By R. J. Sheets

In 2009, the Gold Quarry openpit mine experienced multiple large-scale slope failures of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope failures occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower, high plasticity subunits of the Carlin Formation. This deformation created preferential flow paths that allowed ground water from the upper sandy subunits to infiltrate low-permeability, clay-rich subunits, thereby enhancing deformation of the slope toe, which, in turn, destabilized the upper portion of the highwall. The outcome was a 160 m high slope failure that had a lateral run-out of 850 m. The effort to return the pit to ore production required geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with localized, blast-induced slope failures. Back-analyses with numerical modeling software indicated that the failure surface could be shallower, which contradicted the initial failure interpretations. Eventually, drilling results confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the subunits with residual strength properties. The results are a stable highwall within the Carlin Formation following nearly 10 years of repeated slope failures, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new openpit development.

By Donald D. Carr

Four counties in Indiana--LaPorte, Vigo, Vanderburgh, and Switzerland--have potential for deep underground limestone mining because they are in or are near high population areas and have no surface-minable limestone de- posits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Minable seams suitable for aggregate are 120 to 150 meters (400 to 500 feet) below the surface in LaPorte and Vigo Counties, about 90 meters (300 feet) below the surface in Switzerland County, and about 600 meters (2,000 feet) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1980

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By E. E. Caba

Copper smelter flue dusts containing arsenic are hazardous materials requiring environmentally accept-able disposal, preferably with re-source recovery under the RCRA and CRCLA regulations. However, the known resource recovery processes entail capital and operating costs greater than can be justified by the revenue of the recovered metal. Consequently, the smelting industry is tending to forego resource recovery in favor of encapsulation and storage in a certified class I hazardous waste site, or in a dedicated facility located at the source Superfund site. Order of magnitude costs for this option with portland cement encapsulation are estimated at $100 per ton, not including transportation. Industrial adoption of a new resource recovery process re-quires that its cost, including capital amortization, exceed the cost of encapsulation and storage only by the amount of the offsetting revenue from sale of metal. The lime-roast/ammoniacal leaching process is expected to meet this goal.

Jan 1, 1992

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By Duane L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry and presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a United States Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) utilizes the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package utilizes a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgement scheme that provides an effective method of identifying problem areas which may exist in the mine network. The package was written in Fortran for a 64 kilobyte, Z80-based microprocessor-computer.

Jan 1, 1984

By Yakup Cebeci, Leyla Kalender, Ceylan Yarluğkal Altınışık, Hikmet Sis

The abstract highlights the challenges in concentrating complex and non-sulfide lead-zinc ores and emphasizes the importance of froth flotation for their beneficiation. The study focuses on using process mineralogy to understand the flotation behavior of these ores from the Görgü region. The ore samples were characterized using various techniques, revealing oxidation and carbonation of primary minerals. The flotation results were interpreted in light of the mineralogical data, explaining the poor outcomes due to the complex nature of the ore, poor liberation, and lack of hydrophobicity.

Mar 22, 2022

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992