Search Documents

By Paul E. Rosten

This paper describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Company to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Company operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and Western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes .each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously. (1) (2)(3) Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and furnished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate-kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1977

By Gary H. Higgins

The paper by Lewis and Braun l presents experimental and calculational evidence that primary chalcopyrite ores are rapidly oxidized by warm oxygen-bearing water. Resulting solutions contained copper sulfate products of the matrix rock decomposition such as magnesium sulfate and sulphuric acid. Iron was oxidized to insoluble hematite and hydrous iron sulfates. Oxygen injection near the base of a broken and permeable flooded ore deposit was calculated to cause circulation of oxidizing solutions to the entire permeable region. The rate of dissolution of copper and degree of oxygen saturation for given oxygen injection rates were presented. Their work suggests that in-situ recovery of deep, disseminate primary copper deposits is technically feasible. The actual feasibility depends on economics and environmental safety as well, and it is the purpose of this paper to address these two aspects.

Jan 1, 1972

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By S. Acar

"In recent years the gold mining industry has been challenged by declining metal prices as well as having to treat ores that have low grades and are refractory in nature. Many factors must be considered when metallurgical studies are designed to develop process design criteria for these type of ores. These factors are mostly related to the mineralogical and chemical compositions of the ores, the geological setting of the deposit and how the ore/waste will be mined, such as whether openpit or underground, the mine schedule, and the mine fleet type and capacity. The purpose of this paper is to provide an experience-based practical approach to how to select and characterize test samples as well as devise process development metallurgical studies for both oxide and refractory gold ores, and to provide insight into some of the matters that might go wrong during the course of the studies. This paper is intended as both a guide for someone new to the field and also as a reminder for those familiar with the field. IntroductionThe recent decline in ore grades and metal prices have challenged mining companies to reduce capital and operating costs associated with developing new mineral resources. In some cases, metallurgical studies have been sacrificed to prevent cost overruns resulting in inadequate mineralogical, chemical and metallurgical characterization. Consequences have included longer construction schedules, higher initial and working capital, higher operating costs and less than desirable plant performance (Whincup, 2010; Torres, Chaves and Meech, 1999).Mineralogy, geology, mining type and sequence, and the metallurgy of an orebody will determine the process development metallurgical study requirements and eventual process plant design. Therefore, once the geologist has an early indication of a prospective orebody, geologists, metallurgists, mining engineers, and social and environmental responsibility scientists should convene and devise a plan on how to exploit the orebody economically (Lunt, Ritchie and Fleay, 1997).Geologists may find a prospective orebody solely based on grade. However, if the orebody cannot be mined and processed economically, then it is deemed not to be a deposit. An example of this could be a refractory gold deposit, either sulfidic, carbonaceous or siliceous refractory or any combination of those, that may not be mined and processed economically due to reasons such as the physical location of the deposit, depth of the ore lode, or social and environmental concerns. Therefore, an early collaboration between all disciplines must be established.Each orebody may have its own unique mineralogical, geological and chemical characteristics (Guresin et al., 2012). These unique characteristics should be effectively sampled to reduce risks associated with process design and engineering efforts for the process development metallurgical studies. If the sample or samples are not representative of these unique characteristics, then the studies performed will be pointless. The project metallurgist in charge of conducting metallurgical studies should also possess general geology, mineralogy and mine engineering knowledge. Recommended readings are a book on understanding mineral deposits by Misra (2000) and articles on heap leach development by Scheffel (2014a and 2014b)."

Jan 1, 2016

By L. L. Chasko, D. W. Alexander

Los investigadores del National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research han evaluado los efectos que la malla de control de suelos podría tener en la distribución de polvo flotante de roca y carbón en minas de carbón. El creciente uso de mallas para controlar el desconchado o caída de material del techo y las vigas introduce superficies elevadas adicionales para recolectar el polvo de roca o de carbón. Es posible que el potencial para la propagación de explosión del polvo se incremente si el polvo flotante de carbón no es convertido en inerte de manera adecuada. Adicionalmente, la malla podría interferir con la recolección de muestras representativas de polvo cuando se usa el método de recipiente y brocha desarrollado por la U.S. Bureau of Mines y usada por la Mine Safety and Health Administration para muestreo de banda. Este estudia hace una estimación del polvo de roca o carbón adicional que pudiera acumularse en la malla y desarrolla un método para recolectar muestras de polvo representativas atrapado en las mallas.

Jan 1, 2014

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By Brig M. Moudgil

It was reported earlier that francolite and dolomite from the South Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved at a reconditioning pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1984

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By E. h. Erwin Gaertner

Before dealing with the technical equipment of this paper a short survey of the Rhenish Brown Coal Area is given in order to illustrate the special geologic and environmental conditions in this region, which led to the development of the mining technics, used today.

Jan 1, 1975

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By J. M. Van Langen

In 1965 Hoogovens was looking for additional capacity for burden preparation in the order of 2,5 to 3 million metric tons per annum of some kind of optimal blast furnace ore feed. In principle four solutions offered them-selves for further investigation: 1. purchase of screened ore and/or run of mine ores with the provision of a corresponding ore screening capacity on the blast furnace site; 2. manufacture of sinter; 3. purchase of pellets; 4. manufacture of pellets. After studying the technological, technical, economical and commercial factors Hoogovens decided for the last mentioned possibility. Before taking this decision not only a great number of different mixtures of iron ore were tested, but during a long period in one of the big blast furnaces a number of tests were also executed with purchased pellets from South and North America. It was found, that using 50% acid pellets with 40% basic sinter a coke rate saving of 25 kg per ton hot metal (50 lbs/net THM) and a production gain of 15% could be obtained as compared with a full sinter practice. With some pellets it became clear, that due to properties, commonly referred to as swelling, we got very poor furnace performances; so in studying the production of pellets, pellet quality should be regarded as the most important aspect of the problem.

Jan 1, 1972

By D. W. Park

A vast majority of longwall operations in the United States use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite element model of the shield structure was made to study responses of each long wall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested to develop a technique incorporating the finite-element method to evaluate the real-time shield performance for the purpose of effective ground control.

Jan 1, 1992

By Edward Burris, Terry Gorsuch, Joseph M. Hans

INTRODUCTION In any large earth-moving operation, good planning and management are necessary to complete the operational tasks promptly and successfully. When an earth moving operation is complicated by radioactive contaminants, normal earth moving techniques and procedures must be modified. Any planning and management, therefore, must include the radiological aspects of the operation. It was found that the radiological aspects dominated most of the planning and management activities and were extended to all facets of the decontamination work at the former Shiprock uranium millsite. These planning aspects are discussed and their use to develop a work plan is described. The management aspects are discussed and their use to establish a management structure are also presented. PLANNING Some method of procedure, formulated beforehand, was necessary to govern the decontamination work at the former Shiprock uranium millsite. This procedure was expressed in the form of a work plan which served several listed purposes. 1. It defined the work to be done and the sequence it would follow. 2. It was used as a yardstick to measure progress. 3. It was used to assign organizational responsibilities. Several factors were considered to aid in the development of the plan. These factors are discussed below: Goals It was established that radiation exposure was occurring to persons working at the millsite, and in an around the community of Shiprock, from airborne radioactive mill wastes and radon-222 exhaling from the tailings piles. The goal set for the decontamination work was to reduce on-site exposures to levels acceptable for the millsite occupants. The attainment of this goal would also have a substantial impact in reducing off-site exposures. The objectives necessary to achieve the goal were consolidation and containment of the wastes. The former objective implies decontamination of the millsite and environs, and the later implies stabilization of the wastes. In practice, a total and complete decontamination of the millsite and contaminated environs would be very difficult and costly. The costs for decontaminating them could be high enough that an alternative method might be more cost-effective for reducing human exposures (i.e, move the affected people away from the source). The interim guide "Radiological Criteria for the Decontamination of Inactive Uranium Millsites" was used for the decontamination criteria (EPA 74). Briefly, the criteria state that off-pile decontamination should be effective enough to reduce the net above ground exposure rate to less than 10 [u]R/hr for unrestricted use of the affected area. When decontamination cannot readily be achieved, the exposure rate levels could be relaxed to 40 [u]R/hr; however, the affected area has to be restricted. The second objective, waste containment, means isolating the wastes from the biosphere. Since no method of containment was available at the beginning of the millsite decontamination effort, temporary containment (interim stabilzation) became the objective. The tailings pile and decontamination wastes would be covered with clean fill. The interim stabilization should last from 5 to 10 years until the final disposition of the wastes will occur. The goal, therefore, would be achieved by decontaminating the off-pile areas to less than 10 uR/hr where practical. The decontamination wastes would be used to plate the surface of the tailings pile and would be covered with clean fill. Radiological Survey The radiologial survey is the key factor for planning a decontamination activity. The survey should delineate the spread and depth of the contaminants relative to the decontamination criteria. Surface wastes, in general, can be evaluated for spread and depth with reasonable radiation survey equipment. Subsurface wastes on the other hand can be missed entirely, as happened during the radiation survey at the Shiprock site, although numerous exploration holes were bored and dug. The survey results can be used to define areas that may not be amenable to decontamination because of complications or safety reasons. For example, no decontamination of the bluff base was to be attempted because of the possibility the bluff might collapse on the personnel and equipment. Contaminated bottoms of decant ponds on the flood plain were not removed because they would be slurried by ground water. Slurry removal was deemed inefficient because the contaminants would be scattered and no equipment was available for its transport. In summary, the radiological survey defines the boundaries of the decontamination work and provides

Jan 1, 1981

By C. M. Bristow

The mineral kaolinite is one of the commonest minerals in the uppermost 10 m of the continental crust; ranking in abundance alongside minerals like quartz, mica, feldspar and calcite. Only very exceptionally does it possess all the necessary properties needed to make it worth commercially exploiting. The terms 'Kaolin' and 'Kaolinite' are derived from a locality known as 'Kau-ling', in Jiangxi Province, Peoples Republic of China; where samples of a white clay used by the Chinese to make porcelain were first obtained by European missionaries and explorers in the eighteenth century.

Jan 1, 1986

By D. J. Barratt

What is meant by "Minimizing Risk"? This paper explores some of the factors encountered in plant design which can affect the success of a mineral processing plant in terms of its planned output, quality of product and recovery. Any deficiency in either one of these objectives means lost revenue at the start of a project and reduced present value for the mine life. Time is money. Related factors such as project conception, feasibility studies, capital cost and operating cost estimation and mining studies have been covered in a recent paper (1) from which material for this paper has been drawn. What follows is a discussion of the principal factors which can influence the success of a project with particular emphasis placed on processing concepts.

Jan 1, 1983

By Erik Klohn

The El Soldado copper deposit occurs in volcanic rocks of alkaline affinity of Lower Cretaceous age. The orebodies are discordant and show strong structural and lithological control. The mineralizing event was accompanied by hydro- thermal alteration expressed as carbonatization, silicification, and chloritization. Individual orebodies contain bornite-chalcopyrite cores which are surrounded by haloes dominated by chalcopyrite and pyrite respectively. The sulfur isotope composition of copper sulfides strongly suggests the sulfur is of magmatic origin. Fluid inclusion studies show the mineralizing fluid to be a highly saline NaC1-CaC12, brine. No evidence of boiling was found. The deposit is most likely of epigenetic origin. Hydrothermal fluids were produced during crystallization of a sodium rich trachytic magma during the waning stages of an episode of alkaline magmatic activity. Similar copper deposits along the Chilean Coastal Range may also be associated with alkaline host rocks.

Jan 1, 1986

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By C. L. Lin

Linear grade distribution measurements determined from polished sections of randomly oriented particles can be used to estimate the extent of liberation for multiphase particles of specified size. Two techniques, optical image analysis and microprobe analysis, have been used to establish linear grade distributions. Both techniques were evaluated and compared using variable grade samples of products from a copper porphyry flotation circuit. The statistical significance of the linear grade distribution data obtained by optical image analysis was assessed. The average chalcopyrite content of these samples, as determined by chemical assay was used to estimate the variance of the experimental procedure. For a given accuracy, the number of particles required to obtain an unbiased representation of the sample was determined.

Jan 1, 1985