Search Documents

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By Lawrence Neal Post

Introduction Synthetic soda ash production began to decline in the late 1930s. This was due to high operating costs and waste disposal problems. Since soda ash was used as a major component in manufacturing glass, an alternate method of producing that chemical was necessary. A process to produce soda ash from trona was developed by FMC Wyoming Corp.'s predecessor, as well as an economical way to obtain trona. Existing trona operations are located about 40 km (25 miles) west of Green River, WY. Five operators presently mine trona in this area. FMC's property has 153 km2 (59 sq miles) leased. Its eight shafts reach 488 m (1600 ft) deep to the uniform trona deposit. The seam ranges in thickness from 2.4 to 3.6 m (8 to 12 ft). History Egyptian tombs, dating from 4000 to 3000 BC, contained mummies preserved by an embalming process using soda ash. For many years, soda ash was produced by burning marine plants, then dissolving the soluble material (sodium carbonate) from the ashes. The name soda ash is derived from this method of production. In 1791, Nicola LeBlanc developed black ash, or salt cake, from salt, sulfuric acid, coal, and limestone. This process remained in use until 1863, when Ernest Solvay developed a method for producing soda ash from salt, coke, and limestone with ammonia as a catalyst. This Solvay process was widely used. And, in the 1930s, there were 17 plants in the US alone. High plant operating costs and waste disposal problems, however, necessitated finding an alternative to the Solvay process.

Jan 10, 1985

By A. J. Getz

Major precious metals projects are underway in Australia, Papua New Guinea, Indonesia, the Philippines and New Zealand. This article reviews the status of those projects. Included in this review are project location, reserves, method of resource exploitation, anticipated production, and other unique conditions. The article is limited to major precious metals projects in the Western Pacific region. This is not meant to negate the attractiveness or importance of the many other projects in that area. The geographical setting of these five countries are shown in [Fig. 1]. The gold output of the countries has increased dramatically during the 1980s. [Table 1] compares 1980 and 1988 production figures. The compound growth rate is 120%. That reflects the attractiveness of the region’s resource base as well as the impact of price increases, new exploration models and processing technologies, and changes in government policies. If the 10 projects discussed here are all brought onstream, their combined output - at about 130 t (4.17 million oz) - would amount to an increase of greater than 50% over 1988 production from this region. Table 2 shows indicative production levels for each of the 10 projects. Dollar amounts are in US currency unless otherwise specified. Australian dollars have been converted to US dollars at the rate of 1.28: 1.00.

Jan 1, 1990

By R. L. Grayson, Y. J. Wang

An application of material requirements planning (MRP) to coal mine inventory control is presented. MRP is an efficient material control system that integrates the production planning and inventory management functions. Net material requirements are determined from the production forecast utilizing bill of material files, the inventory status file, and the purchase order status file. Net requirements are computed for each period in a specified planning horizon, and purchase orders, offset by lead time, are initiated routinely to ensure timely receipt of materials. The MRP system is especially useful in production-inventory systems in which con¬sumption of materials is directly production dependent.

Jan 1, 1987

By Chaitanya "Teny" Mittal

INTRODUCTION A team effort by the Owner, Engineer, and Contractor can help avoid serious problems on a construction project. It can save cost and time for both Owner and Contractor, as illustrated in the following case history of the West Zone and Siouf Keblia Collector System in Alexandria, Egypt (Contract 02-AID-83/84). Under the bilateral agreement made in 1980 between the United States of America and the Arab Republic of Egypt, the United States, through the Agency of International Development (USAID), gives approximately $1 billion per year as a grant to Egypt for various development projects. The Alexandria Wastewater Management System was selected in 1981 as one such project. The Egyptian Government Agency responsible for this work is the Alexandria General Organization for Sanitary Drainage (AGOSD). A joint venture of two U.S. consulting engineering firms, CH2M HILL, Inc., and Metcalf & Eddy, Inc., called Wastewater Consultants Group, along with two local subconsultants, Engineering Consulting Group and Warith Engineering Co., were selected by AGOSD to study the sewer system and develop a plan to serve the immediate and long-range sewage disposal needs of Alexandria. Wastewater Consultants Group is currently involved in Phase I of the Master Plan. This initial step in providing Alexandria with an operating sewerage system for the current and near-term population (year 2000) consists of the design and construction management of 140 kilometers of collector and force main pipelines (including 9 miles of pipe jacking and tunneling in very soft clay), five new pumping stations, extensive rehabilitation of two treatment plants (built in the 1960s but never operated successfully), and installation of a sludge handling system. Phase I is scheduled to be completed by the end of 1991 at a total cost of around $250 million (US) plus 250 million

Jan 1, 1989

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn't center itself anyway. If it's possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I'd now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By G. Brien, O&apos

Selective in-plant breakage was investigated at a Central Queensland, Australia mine. Component seams and size fractions from in-plant samples were characterized petrographically and probability analysis of vitrinite reflectance data used to track the distribution of seam proportions through the plant. Results show that the 2 seams reported differentially to coarse and fine circuits, mainly as a function of coal type rather than rank. Seams were also preferentially concentrated in different size fractions of the coarse circuit. Breakage in the coarse coal centrifuge generated approximately 4% of -0.5 mm fines, but was not seam specific.

Jan 1, 1996

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By J. Roth

PROLOGUE Nowadays, where production costs and energy costs are increasing and at the same time requirements in fineness and purity of industrial mineral products are getting higher and higher, industry has to look for more efficient grinding systems and developments to produce these products more economically. Therefore lots of new developments in high energy jet mill pulverizing have been made. In the main, however, these developments involved more or less just the new principle of fluidized bed jet pulverizers but not the older spiral jet mill principle. In some cases, especially in the filler industry where laminar minerals are used and higher aspect ratios are required, the spiral jet mill principle has advantages in a better delamination of these minerals. To comminute minerals down to products with a d97 < 3 µm, the specific energy consumption increases up to 2,000 kWh/t – 3,000 kWh/t or even more, depending on the grindability of the mineral. So the production of these fine materials is quite an expensive task. But jet mill grinding is and will be the most favorable method to produce micro-products and in the near future nano-products, despite the high energy consumption.

Jan 1, 2000

By Fred V. Carrillo

California was the leading state in industrial mineral production value with an estimated value of nearly $2 billion. In total value of U.S. non-fuel mineral production estimated for 1992 by the U.S; Bureau of Mines, California ranked second; 81 % of California&apos;s total production value was derived from industrial minerals. California led all other states in the production of boron minerals, portland cement, diatomite, calcined gypsum and construction sand and gravel, and ranked second in potash and soda ash production. California&apos;s five leading industrial minerals in terms of value were portland cement, construction sand and gravel, boron, crushed stone, and soda ash. California had 13 additional industrial minerals production with reported sales of over $1 million including; industrial sand and gravel, magnesium compounds, lime, salt, potash, natural sodium sulfate, clay, feldspar, crude gypsum, pumice, dimension stone, calcium chloride and perlite.

Jan 1, 1995

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world&apos;s longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I&apos;m Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

During the modeling of grinding systems, population balance modeling (PBM) which considers a constant breakage rate has been widely used over the past years. However, in some cases, PBM exhibited some limitations, and time-dependent approaches have been developed. Recently, a non-linear framework which considers the traditional linear theory of the PBM as a partial case was introduced, thus allowing the estimation of product particle size distribution in relation to grinding time or the specific energy input to the mill. In the proposed model the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (RR) distribution. Besides, the adaptability and reliability of the prediction model are among others dependent upon the operating conditions of the mill and the adjustment of the RR distribution to the experimental data. In this study, a series of grinding tests were performed using marble as test material, and the adaptability of the non-linear model was investigated using three loads of single size media, i.e., 40, 25.4, and 12.7 mm. The results indicate that the proposed model enables a more accurate analysis of grinding, compared to PBM, for different operating conditions.

Jun 24, 2023