Search Documents

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By Antti J. Niemi

Radioisotope tracers have so far been used for extraction of residence time distributions of flotation devices. They have also been proven applicable to evaluation of rate coefficients k of industrial flotation. It is now shown how values of k are scaled up on the basis of laboratory data on flotation and chemical conditioning, and of laboratory testing of samples from output of industrial conditioning vessel. Subsequently a model of conditioning and flotation is obtained which may be used for simulation and control of the steady state of the combined process. Discussion extends to modelling, simulation, CAD and opti- mization of flotation plants with re- circulation, and of ore dressing systems which consist of grinding and flotation plants.

Jan 1, 1990

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

"INTRODUCTION Foam, unless intentionally created, in any industrial process presents operational problems, or at a minimum, is a nuisance. Some foam problems are unique to a given industry and others are common across many industries. A few problems foam presents to any particular industry are: (a) Poor Housekeeping, (b) Environmental impact, (c) Safety Hazards, (d) Slower Production Rates and, (e) Reduced quality of the end product. Defoamers address these issues. Sadly, the assumption in most industries is all defoamers are alike. In reality, a lot of chemistry is involved in the manufacture of even the simplest defoamer sold today and rarely are any two defoamers “just alike”. Today’s defoamers can include polymer chemistry, fatty esters, alkoxylated alcohols, silicone chemistry, silicone surfactants, ethoxylated and propoxylated block polymers, and a tremendous amount of emulsion chemistry just to name a few. This paper will discuss the various types of defoamers, defoaming mechanisms, the advantages and disadvantages of defoamer selections, and how to choose the proper defoamer for your application. Before a discussion of defoamer can be brought about, foam generation and composition must be discussed. WHAT IS FOAM? Foam is a colloidal suspension of a gas dispersed in a liquid. Most often foam consists of air dispersed in water. If a stream of air is introduced into a liquid, the bubbles produced assume a spherical shape. As the density of the bubble is less than the liquid the bubble rises. When the individual bubbles reach and pass through a surfactant free liquid they collapse. Air from the bubble dissipates and the liquid previously surrounding the bubble flows back.It should be noted a pure liquid will not foam. In the case of air dispersed in water a surfactant is necessary to make the water support a stable foam. A surfactant is a term used to describe a surface active agent; a compound with a hydrophilic end and a hydrophobic end on the same molecule."

Jan 1, 2016

By Ray Soper

Important progress has been made in developing the K-Process as an alternative to cyanide as a method of recovering gold from ores and other materials.

Jan 1, 1998

By Michael Gauna, William J. Gray, Joseph C. Zelanko

Mechanized mining in the underground coal industry has continued to evolve since the introduction of the remote control mining machine. Remote control continuous mining machines without an onboard operator’s compartment are now the norm in the industry. Extended cuts in excess of 30 ft (9.1 m) are commonplace. Unfortunately, machine operator positioning has become an often unrecognized safety concern, particularly when remote control continuous mining machines excavate a turn (turn a crosscut). From January 2001 through July 2004, remote control continuous mining machine operators or helpers have been involved in ten roof fall fatalities and eight machinery crushing fatalities. The machinery crushing incidents occurred when machines were being repositioned or moved to another place. Of the ten roof fall fatalities, three occurred while a crosscut was being turned and a fourth fatality occurred while mining was being conducted adjacent to the crosscut. The operating time associated with turning crosscuts is a relatively small part of the mining cycle. In recent years, however, a disproportionate number of fatal incidents appear to have been associated with this activity. Procedures for reducing the incidence of operator fatalities while turning crosscuts are discussed. These techniques include: minimizing the number of turn cuts, limiting turn cut depth, establishing no work zones and using visual warning devices to designate them, installing more roof/rib support in the vicinity of the turn cut, using notch cuts prior to initiating a full turn cut, and positioning the remote control miner operator in nontraditional locations.

Jan 1, 2005

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

By George R. Mitchell

It is a common observation that objects having, different; temperatures exchange energy by radiative transfer. The quantity of radiant energy emitted by an object is a definite function of its temperature. Therefore, a measurement of emitted radiation, by means of a calibrated radiometric instrument, provides a temperature measurement without contacting the emitting object. The physical laws describing radiant energy transfer and their application to remote temperature measurement form the substance of this paper. The energy radiated by bodies having temperatures up to 4000°C is largely in the infrared spectral region. The infrared spectral region is that part of the electro-magnetic spectrum having wavelengths longer than visible light and extending to the microwave region. The wave-lengths range from 0.7 micron (1 micron = 10-4 cm) to 1000 microns. In general, infrared radiometry deals, with the methods of measuring energy flux in the 1 to 15 micron region of the infrared spectrum.

Jan 1, 1960

By James H. Nulty, Joseph S. Roti

INTRODUCTION During a recent panel discussion on the topic of millwater antiscalants, the question was posed: "What would you like to see in the future?" Answer: 'We need an antiscalant that: can be fed without a pump (no maintenance), functions on residual basis (no fault), can be tested for colorimetrically in sub-part-per- mi 11 ion concentrations (no guessing) and will recycle back to the mill from tailings (no cost).” Impossible? Based upon today's level of technology, such a product does not exist. However, a few of the qualifications listed above are certainly food for future thought. Meanwhile, progress is being made in upgrading three essential elements in this critical area of ore processing. They are: 1. Antiscalant reagent research and development. 2. On-line monitoring programs. 3. Reagent storage and feed systems. The objective of this paper is to out- line the current direction being taken in each of these areas and to present case histories as examples of how theory has been applied in field situations to better improve operations. LABORATORY SCREENING TESTS Recent technical papers have explained the various generic chemical raw materials which are available in the marketplace. While the merits of each chemical component are open to debate, the processes used by most major reagent suppliers to evaluate products in the laboratory are fairly standard. Common techniques incorporate both static and dynamic conditions in the search for the most cost effective product. Static Test Perhaps the most common test procedure used is based upon NACE Standard Test Method 03-74, which is "a laboratory screening test to determine the ability of scale inhibitors to prevent precipitation of calcium sulfate and calcium carbonate from solution." The objective of this test is to measure the change in calcium ion concentration in a container of saturated stock solution prepared from calcium chloride and sodium carbonate which is heated in a water bath. After 12 hours at constant temperature (160°), the mother liquor is pipetted into a beaker and a titrated for gm/l of unprecipitated calcium ion. A simultaneous test is performed on stock solution with antiscalant added. The results are then charted to determine the most effective antiscalant (with respect to preventing precipitation of calcite). It should be noted that this procedure examines only the ability of a chemical additive to retain calcite in a saturated solution where thermal stress is applied. This is commonly referred to as sequestration or stabilization. It has been documented that products which act in this manner (i.e., inorganic and organic phosphates) are good scale inhibitors. However, low molecular weight anionic polymers function in a much different manner by distorting calcite crystal size, shape and charge density, thus preventing scale formation. Because of this different mode of operation, static tests may not prove conclusive where polymers and sequestrants are being compared. The simplicity of this test makes it easily adaptable for field use, although modifications are often made.

Jan 1, 1986

By H. G. Linge

Pyrrhotite (FeS1+x ,0<x<0.15) is an iron sulfide which is considered to be a pest in carbon-in-pulp/ leach (CIP/L) gold processing [l].The perceived influence of pyrrhotite on gold processing by CIP/L is a competing consumption of 02 and CN­as the pyrrhotite dissolves by oxidation [1,2]. The few studies of the oxidation chemistry, kinetics and mechanism of the oxidation ofpyrrhotite are reviewed in detail elsewhere [3].There is broad agreement that the surface of pyrrhotite is very rapidly oxidized to form a thin (e.g. 10 nm) ferric hydroxy-oxide layer which overlays an iron-deficient sulfide lattice covering the original pyrrhotite. The reaction can be summarized thus:

Jan 1, 1995

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico&apos;s Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l&apos;-9" diameter to 2&apos;-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

By Qiu Rongqing, Huang Kongxuan

This paper summarizes the results of treating arsenic­bearing refractory gold concentrates from six gold Mines of Chi­na by using bioleaching method and discusses the conditions of bioleaching processes. Results indicate that Thiobacillus fer­rooxidans T-3 Strain can intensely oxidize arsenopyrite, how­ever oxidation rate and degree differe considerably for different. During initial inoculation of 5 X 106 cell/ml. FeH contration generaly 4 -8 g/1. Sample size > 80 % - 3 20 mesh and pulp density 10 % ( w /v) and leaching time ,1 -- G clays, arsenic re­moval rate reached more than 80 % , Fe extraction ,10 - GO% desulfurization rate 30-45% after bacterial oxidation of 4-G days.

Jan 1, 1992

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By Antonio Nieto, Jesus Castillo

Research and Development (R&D) departments in the mining sector are essential for creating new solutions on productivity, safety, and sustainability. Nevertheless, the selection of R&D projects is complex, often influenced by subjective judgments and uncertainties. This paper explores the application of the Multicriteria Decision Analysis (MCDA) as a structured approach to evaluate and prioritize innovation projects based on various criteria such as safety, cost, environmental impact, and social acceptability. By assigning weights and quantifying criteria, MCDA enhances decision-making transparency and objectivity. This study aims to show a method that facilitates strategic thinking, resource optimization, and stakeholder engagement, ensuring that selected innovations align with the company’s long-term objectives and commitment to responsible mining practices.

Feb 1, 2025