Search Documents

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By Clete Stephan, John Urosek, Ian Anderson

The Endeavour Colliery is operated by Powercoal Pty Ltd. It is located in the Central Coast of New South Wales, Australia. The mine has been in operation for about 30 years, producing around 600,000 tons of export coal annually from two production sections. On June 28. 1995, an explosion occurred underground in the 300 Panel at approximately 9:50 a.m.. There were thirty miners underground at the time of the explosion, all of whom were safely evacuated. From June 29 through July 10, personnel did not enter the mine. However, gas samples of the mine atmosphere were obtained from underground monitoring stations and analyzed. Samples were also obtained from boreholes that were drilled from an adjacent mine. On July 10, the atmosphere at the underground monitoring locations and at the boreholes appeared stable with minimal risk of combustion occurring underground. Plans were developed to begin the recovery of the underground workings. The recovery of the underground workings was completed on July 13. The underground investigation of the explosion began on July 14. The investigation was conducted by the New South Wales Department of Mineral Resources. Technical assistance was pro- vided by the United States Department of Labor's Mine Safety and Health Administration (MSHA).

Jan 1, 1997

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By E. Arioglu

Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence (?Smax) induced by chain pillar convergence has been related to a parameter (h/I -p) by linear regression. (Notations are expressed in this discussion's Fig. I (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goaf may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between ?Smax/m vs. h/1-p. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data.

Jan 1, 1992

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By James P. Bowersox

Modem mineral processing plants handle large amounts of ore and produce large tailing streams. Plant performance can be optimized when the water is quickly recovered with a thickener. The caisson thickener was developed to overcome process and mechanical problems with the conventional traction and center column units. The caisson is a hollow center column that serves as a pump house. The rake arm structure is supported by a hydrostatic bearing which sits on top of the caisson. The caisson thickener with a hydrostatic bearing has operated for many years in several mineral processing applications.

Jan 1, 1981

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By H. Wilcox, M. Prichard, Y. P. Chugh

Environmental considerations related to the disposal of coal combustion byproducts (CCBs) and the impacts of deforestation associated with the harvesting of timber for utilization as roof supports in mines should become more severe in the future, as landfill space and suitable timber reserves become more scarce. To help address these concerns, lightweight artificial supports, such as post and crib elements, that use large percentages of coal combustion byproducts as aggregate have been developed for use in underground mines. These structural products show equal or better engineering characteristics than timber, and they have the potential to replace timber support in underground mines. CCB-based ultralight structural material (ULSM) has also been developed and commercialized for use in the construction of ventilation stoppings in underground mines. The bulk densities of these blocks range from 0.40 to 0.64 g/cm3 (25 to 40 lb per cu ft) with more than 75% CCBs. Efforts are also given to develop and demonstrate large volume CCB-based subgrade improvement technique for road construction. Soil treated with SIUC fluidized-bed combustion (FBC) fly ash developed an immediate bearing value exceeding 25% with a swelling strain of less than I %, which is greater than untreated soils, and met Illinois Department of Transportation (IDOT) standard specifications. In this paper, development procedures, engineering characteristics and beneficial uses of CCB-based structural products are given.

Jan 1, 2002

By S. G. Tough, H. J. Hignett

The Transport and Road Research Laboratory is carrying out tunneling trials at Chinnor, Oxfordshire, with a 5-m-diam, full-face tunneling machine. The work, which is for research purposes only, involves driving the tunneling machine through chalk with most of the physical characteristics of the machine and its power consumption closely monitered. At the Conference a film was shown about this work, illustrating both the tunnel construction and the research program.

Jan 1, 1974

By Alan G. Fricker

Cyprus Gold NZ Ltd will be recovering residual free cyanide in barren gold pulp by air stripping. Laboratory investigations by DSIR have indicated additional advantages by recovering the cyanide from pregnant pulp. These are a lower leach pH, a greater cyanide recovery and less carbon consumption. They have a net economic advantage of $1.20/tonne over recovery from barren pulp. The realisation of these advantages is dependent on three crucial technical aspects -optimum pH for dissolution, the absolute loss of cyanide and the stability of the aurocyanide ion. The laboratory investigations described herein address these aspects. Earlier work had indicated that the rate of dissolution of freely revolving gold discs at constant cyanide ion concentration increased with decreasing pH from 11 to 8. Attempts to repeat the work in a more controlled manner by measuring the corrosion potential and current density have, to date, not been reproducible, but do not contradict the earlier observations. Cyanide recoveries and balances were obtained on leaches at pH 10.5 and 9 at the same cyanide ion concentration -the lower pH requiring three times as much total cyanide. Unaccounted-for losses, unfortunately, exceed the accounted-for losses, making interpretation of the balances difficult. Nevertheless, it appears that the additional amount of cyanide at the lower pH of 9 may not be fully recoverable. It may not, however, prove necessary in practice to use more cyanide at a lower pH. Both the gold and silver cyanide complexes remain available for carbon adsorption, as do mercury, copper and iron. Zinc, and probably cadmium, nickel and lead, may precipitate during stripping, which is an environmental advantage.

Jan 1, 1991

By Yves Picot

Construction of new installations was recently completed in the Port of Tubarao, Brazil, With this expansion the port, operated by Companhia Vale do Rio Doce (CVRD), has become the largest iron ore port in the world, with an annual throughput capacity of 60 million long tons. GROWTH OR IRON ORE EXPORTS Since its formation CVRD has steadily increased the shipment of iron ore to overseas markets. Starting with less than 100,000 tons in 1942, the yearly export volume grew to 1,500,000 tons in 1951, 5,000,000 tons in 1961 and 25,000,000 tons in 1971. The number of different grades of ore also increased during this period. Production of high grade pellets, starting in 1970, further increased the number of ore products to be shipped. In the same period the size of ore carriers increased twenty-fold to over 250,000 DWT.

Jan 1, 1974

By D. E. Ranta, Neil D. O’Donnell, Thad B. Ostrowski

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an orebody block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1992

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

By I. Iwasaki, T. Fujuita

The removal of phosphorus from steelmaking slags is essential for recycling such slags to blast furnaces for recovery of their manganese, iron, and lime contents. Phosphorus is mainly concentrated in the dicalcium silicate phase of the slags (Fujita and Iwasaki, 1988, 1989; Suito, et al., 1977). Slow-cooling of steelmaking slags in an air atmosphere increased the grain sizes of constituent minerals; however satisfactory magnetic separation results could not be attained because of the close association of a strongly magnetic ferrite phase with dicalcium silicate (Fujita and Iwasaki, 1988). Curie point of the strongly magnetic ferrite phase in the slow- cooled steelmaking slags was investigated and an attempt was made to separate the phosphorus-bearing dicalcium silicate phase in ground slag pulps heated to a temperature exceeding the Curie point. Materials and methods Slag samples, heated to its fusion temperature of 1370°C and slow-cooled in an air atmosphere, were ground dry to -90 µm (about 170mesh) in a ring grinder. The ground sample was pulped to 1% solids in distilled water using 1 kg/t sodium hexametaphosphate as a dispersant and separated in a Sala high gradient magnetic separator, Laboratory Model 10-15- 20B, using a 100-mesh expanded metal matrix and 300 m/h flow rate.

Jan 1, 1990

By Y. Ye, J. D. Miller, E. Pacquet, S. Gopalakrishnan

From laboratory research activities during the past five years, it is now evident that effective flotation separations can be achieved with the high-capacity air-sparged hydrocyclone. The effectiveness of the equipment has been demonstrated on a pilot-scale basis (1 tph) for a number of mineral commodities including coal, copper, gold, and industrial minerals using a nominal 5-cm x 50-cm system with separation efficiencies equivalent to those achieved by conventional flotation machines. The high specific capacity of the air-sparged hydrocyclone (100 to 600 tpd per cubic foot of cell volume for a nominal 5 cm x 50 cm system compared to 1 to 2 tpd per cubic foot of cell volume for conventional columns and mechanical machines) makes it especially well-suited for the pro- cessing of low-grade ore. As a result of these pilot-scale successes, a number of plant-scale test programs are planned for larger-diameter units to establish wear characteristics and scale-up relationships for design purposes. The status of the air-sparged hydrocyclone technology is reviewed in the present paper, including a description of the system, fundamental considerations of flotation mechanisms, general discussion regarding the effect of control variables, and the significance of feed characteristics.

Jan 1, 1988

By K. A. Grace, D. E. Ranta

The application of geology does not cease with the discovery and delineation of a mineral resource, but continues in the calculation of the economic parameters that determine reserves. Reserve determination, reduced to essentials, is the determination of the cost of production of a mineral commodity from a resource. This cost comprises mining, processing, waste disposal, reclamation and marketing costs. Geological input is vital in the calculation of the individual cost parameters from mining to reclamation, and even has same impact on marketing. Geology thus has a critical role in the determination of reserves.

Jan 1, 1992