Search Documents

By Randall E. Hughes, John F. Burst

This chapter describes the nature and occurrence of the principal clay minerals that are used as ceramic raw materials, explains how these raw materials are used to produce finished goods, and summarizes positive and negative trends that will affect future demand for raw materials and products in the ceramic industry. The term ceramics was derived from the ancient Greek keramikos (a clay jar). A ceramic product is a material that has been fired to at least 468.3°C (Mitchell, 1983). In addition to being one of our earliest manufacturing and construction materials, ceramic products are among the earliest records of civilization. The enduring significance of ceramics is shown by the fact that, even today, the manufacture of whitewares, brick and related red-fired wares, refractories, and engineered ceramics continues to be a major sector of the US economy. A wide range of materials can be made into ceramic products, although relatively few earth materials make up most of the ceramics in today's markets (Table 1). Most ceramic products are made from clay or a related material. The long history of clay use in the ceramics industry stems from its variable and sometimes unique physical and chemical properties, as well as its ubiquitous occurrence and relatively low cost. Clay is important to ceramics because of its plasticity, moldability and filterability, chemical content, color. refractoriness, solubility. corrosion resistance, electrical properties, and other properties that result from the essentially two dimensional morphology of the individual clay mineral platelets. Because of their basic relationships to the chemical and physical properties of clays, the chemical and mineralogical content have been the subject of continuous studies over the past few decades. Advances in knowledge about the chemical, mineralogical, and physical properties of clays are responsible for most of the advances in processing. The need to remove off-colored contaminants, minerals with low melting points, and soluble salts has resulted in beneficiation by wet processing methods such as water washing. Water washing is restricted to kaolins, although low cost methods of water washing have been extended more recently to ball clays in Europe. High intensity magnetic filtration and flotation technologies have noticeably improved the quality of kaolins and broadly expanded their use in the ceramics industry. In addition to products for construction (e.g., brick, tile, sewer pipe, field drain pipe, cement, fiberglass, roof granules, and paint) and manufacturing (e.g., refractories, kiln furniture, sanitary ware, pottery, and dinnerware), clays are used in calcined form as ceramic fillers, carriers, extenders, and grogs. Ceramics suppliers are under economic pressure in several of these product areas. Manufacture of refractories in America has declined as steel production has decreased. Similarly, dinnerware and tile production have declined because of foreign competition. Fortunately, new uses for clays,

Jan 1, 1994

By A. G. Sciulli, G. P. Ballock, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water.

Jan 11, 1986

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By Jean-François Boucher, Ernest K. Yanful, Mei Lin Shelp, Lionel J. J. Catalan

Shallow water covers for preventing acid production in tailings are based on the principle of minimizing oxygen availability. Resuspension of material from the tailings bed may result in increased oxidation and metal releases since dissolved oxygen is at near saturation levels in the water cover. Resuspension can be caused by waves and currents strong enough to mobilize the surface of the tailings bed. Tailings resuspension was measured with sediment traps in the Upper Cell of the Heath Steele site near Mirarnichi, New Brunswick Canada. Although significant amounts of resuspended tailings were collected in all traps, analysis of resuspended solids and bed tailings suggests that for the observed wind conditions resuspension did not occur at locations where the water cover depth was greater or equal to 1.0 m. Currents were likely responsible for the transport of resuspended tailings from shallower areas to locations where the water cover was deeper than 1.0 m.

Jan 1, 2000

By Barbery G., A. Maachar, M. Bourassa

Laboratory testing for flotation circuit design is carried out on a routine basis in a large number of lab- oratories throughout the world. Usually a sample of ore, assumed to be characteristic of the material to be processed in a future plant, having a mass of the order of a few kilograms, is ground in a batch ball or rod mill, in the presence of water and some re- agents (for pH control, etc. .. ); after dilution to the adequate solid concentration, the resulting slurry is transferred into a laboratory batch flotation machine, having a volume which can vary from 0.5 to 8 10 -3m3. Various types of machines are in common use, manufactured by the same companies that market industrial size flotation machines. The operation of flotation in the laboratory is carried out by an experienced technician, who uses parameters such as impeller rotation speed, air flowrate addition, froth height, froth removal rate, in conjonction with reagent addition sequence, to "test" the ore. After flotation, the froth products ("concentrates"), and the solids remaining in the cell are filtered, dried, and analyzed for the various elements of interest. For flotation circuit design, a kinetic test is usually carried out, in which the froth products obtained at various times are collected to assess the time response of the ore in the laboratory machine with the combination of reagents used. Although this description is rather sketchy, it enables to outline some of the major difficulties in using laboratory data for flotation circuit design: 1. ore sample representatively 2. feed preparation procedure (laboratory compared to industrial scale) 3. laboratory procedures (type of ma- chine, type of operation, experimental errors. . . ) 4. flotation machine scale-up 5. flotation kinetic scale-up 6. flotation circuit design using laboratory data These various points will be discussed in the present paper, in order to stress the problem areas as well as possible solutions. ORE SAMPLE REPRESENTATIVITY It has been stated many times that one of the major problem in designing a flotation circuit is the representatively of the sample to be taken. Sampling of an ore body during prospection and evaluation is a specialized field, which has been progress in with the introduction of geostatistics. The application

Jan 1, 1986

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

Since gold was first discovered in Colorado in the late 1850s' mining has been a major part of the state's economic history, according to Stanley Dempsey, chairman and chief executive officer of Denver- based Royal Gold Inc. While the mining industry has seen some lean times throughout the past century, it has always bounced back. Today, dozens of major gold companies are headquartered in the Denver area. The state's coal mines produced record amounts during 1996. And even some of Colorado's uranium mines are resuming production. Dempsey joined other speakers in addressing the state of Colorado's mining industry during the Colorado Mining Association's (CMA) National Western Mining Conference. Some 800 people attended the CMA meeting, held Feb. 2-5 in Denver. The meeting was the association's 100th since it was incorporated in 1897.

Jan 1, 1997

By Howard Brown

High purity, high brightness limestone deposits in the San Bernardino Mountains and Mojave Desert region occur in upper Paleozoic carbonate rocks which are part of an upper Precambrian and Paleozoic sequence that unconformably overlies crystalline basement. The Paleozoic strata are divided into formations and members, and correlated with strata of the inner Cordilleran miogeocline. The region has been affected by multiple Mesozoic intrusive, contact, and regional metamorphic events. Structure is complex, and includes polyphase Mesozoic folding and thrusting, and complex Cenozoic structures. The area continues to be seismically active. High brightness (white), high purity crystalline limestone deposits are uncommon because their formation is dependent on several geologic processes which include; 1) depositional environment, 2) contact and or regional metamorphism, 3) folding and faulting, 4) uplift and erosion, and 5) preservation through geologic time. The complex geologic history of the San Bernardino Mountains and Mojave Desert region has allowed the formation of several large high brightness, high purity limestone deposits which are currently being mined or will be mined in the future. Specialty Minerals, Inc. (formerly Ptizer), Pluess-Staufer (California), Inc. and Partins Limestone, Inc. produce high brightness, high purity limestone from several quarries in the San Bernardino Mountains. These active mines combined with undeveloped deposits controlled by Pluess-Staufer in the San Bernardino Mountains, New York Mountains, and Bristol Mountains in the Mojave area, contain proven and or indicated reserves sufficient to sustain production through the 21st century Detailed geologic mapping, intimate knowledge of stratigraphy, recognition of complex structures, sampling, drilling and assay data, are proven tools in the discovery and delineation of high brightness, high purity limestone deposits in the San Bernardino Mountains and Mojave Desert region of southern California.

Jan 1, 1995

By Kanaya Koichiro

Doyashiki Concentrator in Hanaoka mine of Dowa Mining Co., Ltd. started the operation in 1943, treating the ore mainly from Doyashiki ore deposits. After the cessation of mining of Doyashiki ore body in 1973, Doyashiki concentrator began to treat the ore from Fukazawa mine instead in the same year, and furthermore the ore from Ezuri mine In 1979. Currently Doyashiki concentrator treats 30,000 tons of ore per month from both mines. The ore treated is complex sulfide ore, called "Kuroko" (black ore), and the principal minerals contained in the ore are chalcopyrite, galena, sphalerite, pyrite, and barite, accompanied by bornite, tetrahedrite, tennantite, covellite, stromeyerite, argentite, polybasite, pearcite, and electrum. The Principal gangue minerals are quartz, gypsum and clay. The grade of the feed to the concentrator averages 0.9 p/t Au, 110 g/t Ag, 1.1 %Cu, 2.8 %Pb, 9.2 %Zn, 5.0 % Pyrite-S and 13% BaS04. The feed is, after washing and two-stage crushing, ground to 88% minus 200 mesh in a rod mill and ball mills with cyclone classifiers, and five concentrates are recovered by flotation. Primarily copper-lead bulk concentrate is recovered by sulfurous acid-lime flotation method, and then from the bulk concentrate copper concentrate is floated by hot pulp flotation method, sinks being lead concentrate. Zinc concentrate is recovered from the tailing of copper-lead bulk flotation, pyrite concentrate from zinc flotation tailing and barite concentrate from pyrite flotation tailing. The final tailing is sent to the dam.

Jan 1, 1982

By L. Xu, N. I. Jayaraman, R. Bhaskar

The objective of this study is to develop a better understanding of the collection characteristics of dust measurement instruments used in mine dust control research with respect to properties of quartz and coal dust. Coal and quartz dust of narrow sues, with aerodynamic median diameters being approximately 2 µm, 4 µm and 10 µm, with quartz contents of l0%, 20%, 30%, 40% and 50%, were released in an aerosol characterization chamber using a fluidized bed aerosol generator. Dust was collected in MSA personal gravimetric samplers with l0-mm nylon cyclones, total dust samplers and Sierra 298 inertial cascade impactors. The samples were analyzed for mass and quartz content. A total of 21 experiments were performed for this study. The mass and quartz collection efficiencies of the total and respirable dust samplers and the impactor were determined. The data show that the amount of dust collected by the respirable dust sampler (respirable + oversize dust trapped in the cyclone pre-classifier) was, in general, less than the amount collected by the total dust sampler. The amount of dust collected by the impactor was higher than that collected by the total dust sampler. Quartz analyses of the airborne dust samples showed that the total dust and respirable dust samplers (including oversize dust) collect less quartz dust than at inertial impactor. The larger the median particle sire of the quartz and coal mixture, the lower the quart content of the dust collected in the samplers. For all three sires, the impactor was a better collector of quartz than the other instruments.

Jan 1, 1994

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By Tetsuo Yamazaki

Natural cold seepages are characterized as rapid upward transports of methane from deeper parts of geological structures to the seafloor. Thermogenic and/or biogenic methane generated in deep sediments moves up to seafloor, and major part of methane is consumed in anaerobic oxidation of methane (AOM) and hydrogen sulfide is created in anaerobic sulfate reduction by consortium of microorganisms. Then the hydrogen sulfide is utilized by chemosynthetic communities near the seafloor, such as Acharax, Calyptogena, Bathymodiolus, and the mat-forming bacteria Beggiatoa (Fig. 1). When the supply of methane is large or rapid, remaining methane escapes from seafloor, and it is aerobically oxidized in seawater. A mass balance ecosystem model of chemosynthetic community around natural cold seepages in sediment layer and on seafloor has been created and improved by the authors (Yamazaki et al., 2005; Takeuchi et al., 2007). The model is constructed from 3 main processes as schematically shown in Fig. 2: (1) Methane supply process; (2) Ecosystem process; (3) Water column process. The part of chemosynthetic communities is in the ecosystem process. A numerical model CANDI (Carbon And Nutrient Diagenesis) was developed by Boudreau (1996) to simulate the biogeochemical processes such as organic matter, oxidant, nutrient, bi-product, and pH diagenesis in aquatic surface sediments. Then, the improved version named C. CANDI was developed (Luff and Wallmann, 2003; Luff et al., 2004). The authors created the same type carbon and nutrient diagenesis process model with calcium carbonate formation like C. CANDI (Yamazaki et al., 2005), and have added the sulfur oxidizing and immobilization processes (Takeuchi et al., 2007). The sulfur oxidizing and immobilization processes are connected with the carbon and nutrient diagenesis process model.

Jan 1, 2008

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.

Jan 1, 1987

By S. Lefond

A glance at the accompanying table and a review of contributors' comments suggest that the industrial minerals industry is recovering from the recession of the past few years. Actually, the total value of nonmetal production in 1983 was $15.5 billion, up 10% over 1982. Nonmetallics still have not recovered to 1981's high of $25.3 billion, but at least it is on the way up. It is significant that cement (+20%), clays (+13%), gypsum (+16%), sand and gravel (+12%), sodium carbonate (+7%), and crushed stone (+11%) are up. These commodities are largely used in the housing and construction industries. Raw steel and steel mill products, iron ore production and castings, and purchased scrap are showing improvement and increased in value last year. They are, however, still not up to the high of 1981. These industries consume considerable amounts of many industrial minerals, such as limestone, dolomite, fluorspar as fluxes, and many types of refractories.

Jan 5, 1984

By Richard R. Klimpel

Part 2 of this article continues the discussion of a 10-year, multimillion dollar research and plant testing program on slurry rheology and grinding circuits. The first part of the article (ME, Dec. 1982) presented the basic concepts identified by the research and some laboratory test results. This section Illustrates typical Industrial scale test results and Identifies some industrial operating implications of controlling rheology by different methods. At least four controllable factors decide the rheological character of a slurry-slurry density or percent solids, particle size distribution, chemical environment, and slurry temperature. The second factor has two interrelated facets: the shape of the particle size distribution which controls packing behavior of the solids, and the fineness of the distribution. Finer particles increase interparticle forces and viscosity. As indicated in Part 1, during a given grinding test it is possible for all four factors to change. However, regardless of the particular settings of the four factors in a given test, if the resulting rheological character is either dilatant, pseudoplastic, or pseudoplastic with yield, the associated breakage rate is correlated with the current rheological character. It is obvious, for example, in batch grinding tests run at constant percent solids, that the second and third factors, where appropriate, are changing during grinding because size distributions are changing and the production of fresh surface area takes up unadsorbed chemical. Thus the corresponding rheological character change in batch tests with increasing grind time would be dilatant to pseudoplastic to pseudoplastic with yield. The degree to which this transformation occurs depends on the changing setting of the four factors over grinding time. In continuous grinding tests, one might logically expect that dramatic changes in any one of the four factors will be less likely to occur. It will be shown that continuous mill operations offer some unique opportunities to take advantage of possible rheological transformation by more direct operational control of the settings for the four factors. One extra observation noted in the rheological studies was the variability in the location and extent of region B (pseudoplastic behavior) for the various coals and ores tested. The location of region B was usually in the region of 45-55% solids by volume and was of the extent of 0-8%, or 2-11% with chemical addition. The corresponding increase in net production ranged from 0-10% in region B and 0-21% in region B&apos;. When region B is small or zero (no pseudoplastic character is exhibited) no increase in production will be observed and the use of chemicals is often marginal. There are several reasons for some materials exhibiting this quick transformation from dilatancy to high yield values often at surprisingly low percent solids by volume such as 30%. One condition identified was for materials containing high levels of viscosity-producing elements such as- carbonates or clays. A second condition documented was for materials that exhibited unusually fine primary fragment distributions (fine B1,; curves). This corresponds to materials having small y values of < 0.5. Such a slurry developed a yield value quickly during grinding because of the rapid buildup of fines. A related problem can be presented by materials exhibiting excessively coarse primary fragment distributions, y values > 0.9. Breakage of this type of material produces size distributions that give poor packing efficiencies even at long grind times, thus hindering the normal rheological transformation presented earlier. A final condition that can cause the occurrance of region B to be small or zero is when the media void volume filling of slurry is < 100%. Figures 5a and 5b use previously published data of this study to demonstrate the influence of solids loading and weight percent solids on the net production of taconite ore in a laboratory batch ball mill. In particular, Fig. 5a illustrates several trends not generally recognized until this study. They include these two: • Increased slurry density allows for increased solids loading before passing through the maximum in the net production curve where the fall-off is due to non first order breakage. • The use of rheology control chemicals such as GA-4272 allows this trend to be extended to higher slurry loadings with an increase in net production over any previous condition by keeping grinding first order. Figure 5b shows the same data as Fig. 5a plotted for constant weight loadings. These various figures of net production versus percent solids show the location and extent of the regions A, B, and C presented in Part 1 as a function of solids loading. It is obvious that the rheological transformation pattern described earlier does not hold true for slurry loadings corresponding to less than the void volume of the media, which is also a region of

Jan 1, 1983

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By R. W. M. Lai

The study of flotation kinetics was first reported by Garcia-Zuniga1 in 1935. Since then, literature on the subject has grown with the time. 2-19 Although there is an abundance of flotation kinet¬ics models available in the literature to describe flo¬tation systems, they are mostly of academic interest and are seldom applicable for use in the industrial environment. Several reasons contribute to the wide gap in the industrial -application of the academic models. These include: 1) the lack of generality in the model, e.g., the model is limited to certain size ranges; 14 2) the academic models involve complicated mathematics; 5,6,10,11 3) confusion about the order of the flo¬tation rate, e.g., several authors proposed a first order rate model, 1,15,16 whereas the others propagated a second order rate model: 2,17,18,194) the use of an unrealistic rigid value, such as the use of a maximum recovery of 100%, 5,8,19 which is unrealistic in industrial operations; and 5) the use of graphs that confuse the reader rather than interpret information. 2,3,10 This paper intends to introduce a simple and easy to understand empirical flotation kinetics model along with a way of presenting the model in an informative graphical form, which should stimulate the interest of other practical engineers to become concerned with practical application within the mineral industry.

Jan 1, 1982

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998