Search Documents

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

By M. J. Howes, C. A. Nixon

INTRODUCTION A safe heat stress control strategy for an underground mine has three elements: Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. Acceptance of a functional relationship between the environ- mental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The environmental measure that reflects physiological strain is the link between the three elements and, since the turn of the century, the discussion of the merits of various indices has been prolific. One problem in selecting a suitable measure or index is the ease with which it can be physically obtained relative to accurately reflecting the physiological strain. For example, wet bulb temperature is simple to measure and, for a particular mining sys- tem, it may adequately represent physiological strain, however, it would not necessarily provide the same relatively safe measure in a different mining system. The acceptance of a measure which can be universally applied has been confounded by both development and predisposition. That is not to say that there is only one "correct" measure and all others are unsuitable. It is self evident that if the application of a particular index has resulted in adequate control, then that mea- sure is correct for that situation. However, an understanding of the limitations is necessary to ensure that adequate control is maintained as mining conditions change. Almost 100 years after the question of heat stress in mines started to be dealt with in a collective manner, an analysis of the available information is leading towards a general strategy to control this problem. In the paper, the developments in heat stress assessment are briefly examined and followed since the earliest published observations on the effect of heat in mines (Haldane, 1905), efforts to determine a relationship between an environmental measure and human performance are reviewed and summarised and the benefits of control strategies such as acclimatisation and shortened shifts are discussed as they relate to Mount Isa Mines. The results of testing the prototype air cooling power instrument are discussed and a heat stress control strategy outlined. HEAT STRESS AND AIR COOLING POWER The operation of the human engine is analogous to other engines where the conversion of chemical energy from the oxidation of fuel to useful mechanical energy is not 100% efficient. In a diesel engine it is about 33% and in a human engine less than 20% resulting in at least five times as much heat produced by the meta- bolic process as useful work done. Metabolic energy production is related to the rate at which oxygen is consumed and is about 340 W for each litre of oxygen per minute. Using measured oxygen consumption and an average body surface area of 2.0 m2, the approximate metabolic energy production associated with different mining tasks is (Morrison et al. 1968):- • Rest, 50 W/m2 • Light work, 75 to 125 W/m2 (machine, LHD or drill jumbo operators) • Medium work, 125 to 175 W/m2 (airleg drilling, light construction work) • Hard work, 175 to 275 W/m2 (barring down, building bulkheads and timbering) • Very hard work, over 275 W/m2 (shovelling rock) Heat balance is achieved when the rate of producing heat (the metabolic heat production rate) is equal to the rate at which the body can reject heat mainly through radiation, convection and evaporation. Heat exchange between the lungs and the air in- haled and exhaled is normally less than 5% of the total and there- fore usually ignored. Any heat not rejected to the surroundings will cause an increase in body core temperature. Since heat stress is related to the balance between the body and the surrounding thermal environment, the main parameters required to be known when determining acceptable conditions are those associated with the heat production and transfer mechanisms. These can be summarised as follows: Metabolic heat production rates (M - W) Skin surface area (A3) (and effects of clothing) Dry bulb temperature (t[ ]) Radiant temperature (t[ ]) Air velocity (V) Air pressure (P) Air vapour pressure (e [ ]) The rate of heat transfer to or from the environment depends on the equilibrium skin temperature t, and the sweat rate S,. These in turn depend on the response of the body to the imposed heat stress and the effect of thermoregulation (Stewart, 1981). Thermoregulation The body contains temperature sensitive structures which send impulses to the brain at a rate depending on the temperature. Both hot and cold signals can be differentiated and the thermoregulatory response ahivated according to which signal pre- dominates. If "cold" signals are dominant, body heat loss is re-

Jan 1, 1997

By E. M. - Technical Papers Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the dis- abling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety

Jan 1, 1987

By K. Park, J. Sohn

Recovery of industrially useful metals from various secondary sources is an important issue in Korea whose natural resources are limited and needs in the strategic metals are on the rise. In order to meet such needs, researchers at the Korea Institute of Geoscience and Mineral Resources have launched a number of projects to help the nation to recover various metals from secondary sources. In this study, silver is successfully recovered from spent silver-oxide batteries first by distillation to remove mercury. The distilled residue was next subjected to leaching of silver using nitric acid. The study involves finding optimum conditions to leach silver from the distilled residue and subsequently to recover silver from the leach liquor by chemical precipitation. The chemically precipitated products are then subjected to reduction roasting to recover silver metal.

Jan 1, 2002

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By John S. Burton

Mineral policy in Canada has been in a state of transition and change over the past several years. 1976 has witnessed some settling of troubled waters and the pattern of the currents of change is becoming more clear. The provinces play a key role in this process and have provided much of the thrust for new initiatives. On the other hand, the federal government in Canada in recent years has taken a much more active interest in mineral affairs than previously and has asserted its powers on a number of key policy questions. Some of the initiatives from the two levels of government in Canada have come into conflict with each other and, thus, contributed materially to a state of affairs that includes change, uncertainty and conflict.

Jan 1, 1976

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007

By Bruce Bryant

Silver ore was discovered at Aspen in 1879, but the district did not reach full production until 1888 after lawsuits were settled and railroads furnished less expensive transportation to the outside world. The boom years were 1888-92; production declined thereafter. From the middle 1920's until 1950, the Midnight mine in the Richmond Hill district furnished most of the output in the Aspen quadrangle. Since 1950, little mining has been done at Aspen. The metals produced were silver, lead and zinc. Native silver dissolved from the sulfide ores was redeposited by waters circulating as deep as 300 m below the land surface, resulting in great secondary enrichment of many of the deposits. Over 100 million ounces of silver were produced in the Aspen quadrangle. Low-grade lead-zinc deposits remain between the old workings locally, and data available suggest that primary ore below levels mined is also of low grade. The ore occurs in the Mississippian Leadville Limestone and the lower part of the Pennsylvanian Belden Formation in sites that were made favorable for deposition by a number of stratigraphic and structural factors.

Jan 1, 1982

By Thomas V. Mullen

Some 146 kt (4.69 billion oz) of gold have been mined throughout history. Of this, 70% has been mined in this century alone, with 17% produced from 1985 through 1996 (Fig. 1 and Table 1). Until the mid-19th century, placers were the chief source of gold. Advancements in mining, metallurgy and geological thinking have resulted in underground mining (first of veins plus stockworks and later of Rand-type deposits) becoming the principal source of gold. With the demise of the South African deposits and the move towards lower grade ores, the primary source of gold will be from disseminated deposits exploited through large, open-pit mines. For the past 200 years, there has been a fairly constant ratio of about 31 g (1 oz) of gold to each person alive. If this ratio is to be maintained, annual gold production will have to rise from about 2.3 kt/a (73.9 million oz/year) to more than 3.1 kt/a (99.7 million oz/year) by the year 2000. To effect this increase, an unforeseen breakthrough in exploration or metallurgy is needed. Barring this, there will be pressure for an increase in the price of gold. This article traces the historical production of gold from 4000 B.C. - the earliest record of gold mining - to today and relates this 6,000-year record to advances in geological thinking, mining engineering and extractive metallurgy. It also proposes that man's thirst for gold, reflected in the price he will pay for gold, and his ability to find, mine and refine gold have combined to effect an equilibrium based loosely on the historical ratio of 31 g (1 oz) of cumulative gold production per each man or woman alive.

Jan 1, 1998

By M. Javier

This concept paper is presented in the hope of raising the awareness of mankind on the necessity for its peaceful coexistence with nature. It is a food for thought. It takes compromise and sacrifice of people, who will have to learn to curb their greed and move toward a more organic form of prosperity. A nature-friendly sustainability is first step toward the protection of nature that is critical to the mutual survival of mankind and nature. People need the resources from the finite earth to survive and nature needs the prevention of human destruction in order to continue to regenerate and provide. The contemporary notion of sustainability is self-serving. It serves the interest of industry by camouflaging itself to look like nature?s protector. The ?sustainability? concept presented in this paper aims to extend the longevity of the utilization of the limited natural resources for many generations to come. It is an important, responsible first step in creating a healthy sustainability concept that, when implemented, extends the longevity of mankind by the most efficient use of the finite resources on this limited Planet Earth, all the while taking into consideration the increase in anthropogenic activities due to exponential human population growth. This new definition of ?sustainability? has completely different characteristics than its contemporary versions. Nature has its own destiny, rules and principles. Being a part of nature, human society depends on it for survival and must play by its rules and never the other way round as in its initial pretensions. Society should not try to humanize nature, but rather to respect the rule of the nature in a peaceful way of co-existence. When implemented, this new concept of sustainability aims to affect the designs of engineered structures and revolutionize the recovery methods and processing of natural resources, such as mineral resources in the most efficient manner. Finally, this paper intends to stimulate critical thinking and initiate serious discussions aiming at producing a general consensus for the best definition for human society to not only enrich, but to extend its existence. Thus, the spirit of this new definition is pro future generations and environment. KEYWORDS: Sustainability Definition, Nature, Geomímic, Deproduction.

Feb 27, 2013

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

By J. B. Hiskey, X. H. Jiang

The extraction of gold from chloride solutions by ion exchange is examined. It is shown that at initial gold concentrations between 1 - 5 ppm, 20 g/l C1- and pH 5, the kinetics of loading on weak base resins are slightly slower than those observed with activated charcoal. Equilibrium loading of auric chloride varies considerably as a function of pH from one resin to another. For all of the resins studied, nearly complete gold extraction was achieved between pH 2 and pH 6.5. Sodium hypochlorite was found to exhibit a slight effect on the equilibrium loading of gold chloride.

Jan 1, 1990

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982