Search Documents

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By Kaye P. Strong, Desmond M. Levins, Anthony G. Fane

1. INTRODUCTION The safe disposal of tailings is the most important environmental question facing the uranium mining industry today. This is because tailings present a major long term radiological hazard as they contain about 71% of the radioactivity originally in the ore. The magnitude of the problem can be appreciated by considering the quantity of tailings involved. For example, projections of milling programs in Australia indicate that there will be 100 million tonnes of tailings produced by the year 2000 (Levins 1980). The United States currently has in excess of 100 million tonnes and by the year 2000 will have between 900 and 1700 million tonnes (Landa 1980). Present options for tailings rehabilitation include leaving them above ground, returning them to the mine or placing them in specially excavated pits. In any event, the tailings will be covered with earth and revegetation attempted. This will remove the problems of airborne radioactive dust and water erosion of the tailings, at least in the short term, but diffusion of radon-222* from the tailings may still occur. The Atomic Energy Control Board of Canada (1981) has proposed a maximum allowable radon flux from rehabilitated tailings of 0.074-0.37 Bq m -2s-1(2-10 pCi M-2 s-1); the exact level is to be determined "after discussion with other regulatory agencies and the industry". The United States Nuclear Regulatory Commission (USNRC 1980) has been more restrictive in recommending a maximum flux of 0.074 Bq m -2s-1 (2 pCi m-2s-1). As a guideline they also suggested a minimum depth of covering material of 3 m to achieve this surface flux for tailings typically found in the western milling regions of the United States. The design of rehabilitation schemes is aided by a knowledge of radon transport through tailings piles. In this paper we present the results of a theoretical analysis and experimental study of radon diffusion through selected Australian tailings and cover material. The minimum cover criteria of 3 m is reexamined in the light of these findings. [ ]

Jan 1, 1981

By Gunnar Thaning

The iron ores mined by LKAB in the north of Sweden have excellent beneficiation properties. This gives LKAB a favourable position as regards the production of low silica pellets for direct reduction. LKAB have concentrated on developing and marketing grades of pellets for the Midrex-Purofer-HyL process group, i.e. such D.R. processes which are carried out in a shaft furnace or a static bed using reformed natural gas as a reducing agent. The paper deals with properties and quality demands of iron ore pellets for such processes. Matters such as the effect of the residual magnetite in the fired pellets on the degree of metallization, the amount and composition of the slag phase in the pellets, the mechanism of the disintegration during reduction, the state of swelling of the pellets during the conditions prevailing in these processes, the importance of the porosity, the improvement of the reducibility and lowering of the sticking tendency of the pellets by small additions of suitable additives and the influence of the pellet size are discussed. A special test procedure for D.R. pellets has been elaborated by LKAB. Thus, three metallurgical properties are routinely determined separately, namely reducibility, reduction strength and sticking. The test methods are described. Finally the present and future LKAB pellets for direct reduction are presented with respect to chemical analyses and metallurgical properties.

Jan 1, 1978

By Kathleen Kreiss, A. James Ruttenber

INTRODUCTION Early in the morning of July 16, 1979, there was a breach in the earthen retaining dam of a tailings pond at the United Nuclear Corporation's (UNC's) Church Rock uranium mill. The acidified liquid and tailings slurry spilled through the damaged portion of the retaining wall into an arroyo that is a tributary to the Rio Puerco river system. The Rio Puerco runs through Gallup, New Mexico, and eventually crosses the New Mexico-Arizona border (Fig. 1). On its way to Gallup, the Rio Puerco and its tributaries pass through land with a checkerboard pattern of ownership, with portions owned or leased by the Navajos, individuals, the Bureau of Land Management, and the State. In terms of tailings liquid volume (3.6 x 108L; 94 million gal), the UNC spill ranks as one of the largest. The mass of solids released in the slurry (10.0 x 105 kg; 1 100 tons) appears to be close to the median for accidents of this kind, however [U.S. Nuclear Regulatory Commission (NRC), 1979]. The UNC first opened its Church Rock uranium mill in 1977 on land adjacent to acreage belonging to the Navajo tribe. The mill, which is next to the UNC Church Rock mine, is located approximately 16 km (10 miles) northeast of Gallup, New Mexico (Fig. 1). Gallup, a town of 18 000 people, is the closest population center. The region surrounding the plant site is sparsely populated by Navajos, at a density of approximately 5.8 persons/km2 (15 persons/sq mile). The UNC mill and mines employ approximately 650 persons, and the adjacent Kerr-McGee uranium mine employs about 300. The UNC mill normally processes 3.2 x 106kg/day (3 500 tons/day) of uranium ore, depositing the acidified tailings slurry in a series of three earthen holding ponds. The tailings ponds are located east of the pipeline arroyo that feeds into the Rio Puerco approximately 2.4 km (1.5 miles) from the southernmost tailings dam. The liquid portion of the tailings slurry evaporates in the ponds; hence, under normal conditions, there is no surface flow from the holding ponds to the arroyo. Both runoff from the plant site after heavy rains and possible seepage from the tailings ponds may deliver radionuclides to the arroyo-river system, however. The dam across the southernmost tailings pond was considered to be in keeping with the state of the art. However, the New Mexico Environmental Improvement Division (NMEID) had warned UNC about dangers of locating the pond over a heterogeneous geological formation. The state Engineer's Office approved of the site only after UNC agreed to strict design criteria. Others have pointed to dangers of constructing earthen dams for impoundment of uranium mill tailings (Carter, 1978). Causes of the dam break were multiple: the UNC mill filled the tailings pond to a level that exceeded permit criteria; the tailings pond was lined improperly; the dam was constructed using clay that was compacted excessively, resulting in cracking and subsequent seepage; and the unstable substrate beneath the dam permitted differential settling. The UNC Church Rock mine has continuously released dewatering effluent into the pipeline arroyo at a rate of 88.3 L/sec (1 400 gal/min) since 1968. Before 1975 this effluent was not treated; after 1975 it received precipitation treatment for removal of Ra-226. Radionuclides are also released into the river system through the dewatering of the Kerr-McGee uranium mine 1.6 km (1.0 mile) north of the UNC mill. During usual mining operations, approximately 227 L/sec (3 600 gal/min) are released into the pipeline arroyo and subsequently into the Rio Puerco. The Kerr-McGee mine began continuous release of dewatering effluent in January 1972. In 1974 Kerr-McGee began Ra-226 precipitation treatment of its dewatering releases, but NMEID data indicate that treatment has often been incomplete. The effluent from both mines has been responsible for transforming the downstream portion of the Rio Puerco from a sporadically dry riverbed into a continuously flowing stream and has contributed to the current levels of background radiation along the river system (Table 1). This paper will summarize the postspill monitoring efforts and relate the assessment of this spill to the general question of evaluating the health effects of nuclear fuel-cycle wastes. The data pertaining to the measurement of radionuclides in the Church Rock environment and the radionuclide concentrations in animals will appear in forthcoming reports. CHURCH ROCK HEALTH EFFECTS ASSESSMENT APPROACH The initial health effects evaluation involved identifying the radionuclides that were released into the river system from the tailings pond. Table 1 lists the State of New Mexico maximum permissible radionuclide concentrations for liquids released to unrestricted areas, the typical tailings liquid concentrations, and postspill river water concentrations. The tailings liquid contained comparatively high levels of Th-230, Ra-226, Pb-210, and Po-210--all of which, according to postspill river water samples, had exceeded the state maximum permissible concentrations (MPC) at one time or another. After the radionuclides in the tailings were identified, pathways through which humans could be exposed were clarified. Environmental monitoring data were then used to quantify the important pathways of human exposure. Water samples were collected from the river, from test wells dug near

Jan 1, 1981

By L. C. Raymond

Good afternoon. I have entitled my talk "Investment for Progress," implying thereby a spark of friendly competition by private enterprise with such government-inspired foreign aid and investment programs as the Alliance for Progress. While the subject of foreign investment is hardly a new one, the perpetual flux of the political and economic surface of this earth we inhabit makes it forever timely and forever interesting. Especially do tremendous opportunities for international investment constantly present themselves to the mineral industry, and just as often must the industry approach these opportunities with a great deal of investigation and caution. This is not to say that the mineral industry--no less than any other industry--should be unenthusiastic about the foreign scene, but like everyone who proposes to put his money where his hope is, it should consider all the factors and weigh the possible disappointments as well as the rewards.

Jan 1, 1964

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By Rongjie Kong, Shiwei Wang, Dongjiao Gui

Metal cations have significant effects on the flotation of coal and minerals. In this study, the effects of monovalent cations ( Na+ and K+) on the flotation of low-rank coal (LRC) were investigated using flotation and particle–bubble attachment experiments and through X-ray photoelectron spectroscopy (XPS) and molecular dynamics simulations. Oleic acid (OA), methyl linoleate (ML), hexadecyltrimethylammonium chloride (CTAC), ricinoleic acid (RA), and kerosene were used as flotation collectors. The flotation experiments revealed that the flotation yields of LRC improved when OA, ML, RA, CTAC, and kerosene were used in pure deionized water. However, flotation was suppressed for these collectors in the presence of K+ and Na+ ions. In contrast, when using CTAC, the flotation yield increased in the presence of these ions. Specifically, the flotation yield increased from 41.24 to 87.03% when 2.0 kg/t CTAC was used in 10 mmol/L NaCl solution. Particle–bubble adhesion experiments and XPS revealed that the hydrophilic groups of CTAC were adsorbed on the LRC surfaces by electrostatic forces, whereas the oxygen-containing functional groups of OA, ML, and RA formed hydrogen bonds with the LRC surface in pure water. Finally, the simulating result revealed that the hydrophobic ends of the OA, ML, and RA collectors hinder the flotation of LRC by adsorbing monovalent cations, whereas the adsorption of monovalent cations on the hydrophobic end of the cationic surfactant (CTAC) promotes flotation via strong electrostatic interactions.

Jan 31, 2024

By J. P. McDonald

Exposure to particulates containing metals and metal fumes (PCMMF) is a potential concern in ore refining and smelting. Some metals of primary interest are arsenic, cadmium, copper and lead, which have been linked to various adverse health effects. The current National Institute for Occupational Safety and Health (NIOSH) sampling method for metals in particulates requires the use of a filter, precision airflow pump and laboratory analysis. A major concern with this method is the one-to-two weeks? wait before laboratory results are available for use in determining if additional controls are needed to assure adequate exposure protection for workers. Particulates containing these metals were sampled during sixteen sampling events at a copper smelter using the traditional NIOSH methods. Monitoring of particulates was simultaneously conducted using a TSI 8520 Dust-Trak real-time aerosol monitor with a 10-µm-cutpoint sampling inlet. NIOSH analytical methods related to particulates and metals (methods 0500, 0600 and 7300) were used to determine particulate mass and individual mass contributions of metals on sample filters. Linear regressions with y-intercepts forced to zero were developed to determine the relationship between the PM10 measurements recorded by the DustTrak and laboratory-reported total particulate mass, PM10 and respirable arsenic, cadmium, copper and lead concentrations. These linear regressions yielded correction factors that can be applied to DustTrak readings to obtain total particulate mass, PM10 and respirable concentration estimates for each of the four metals. The R2 (coefficient of determination) values from the linear regressions ranged from 0.65 for total lead to 0.91 for total copper. These results suggest that the DustTrak may produce real-time data useful in providing estimates for airborne concentrations of arsenic, cadmium, copper and lead in copper smelter particulates.

Jan 1, 2011

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2009 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on industry exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2009: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2009 and were compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2009, primarily for base metals (copper, lead, nickel and zinc), diamond and precious metals (gold, platinum-group metals and silver). Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis prior to 2008. The MEG survey methodology was changed in 1999 to include companies with exploration budgets greater than $100,000, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2009 survey is reported by MEG to cover an estimated 95 percent. Companies who chose not to participate in the MEG study, private companies that do not publish data and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 86 more companies in its 2009 survey than it did in 2008.

May 1, 2010

By C. C. Muir

At the outset, I believe reference should be made to comparatively recent world developments in copper which have an important bearing upon the Canadian position. COPPER SITUATION No one can doubt the marked change for the better compared with not so long ago when less than adequate attention was paid to marketing and to uses of the metal. I need not show you graphs of world copper prices, which except for relatively brief periods and war conditions were, until about three years ago, not unlike the topography of the Canadian Rockies. There remain, of course, some non-industry factors who yearn for the old days of "roller-coaster" copper prices.

Jan 1, 1964

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

By W. A. Haley

The use of diesel engines in underground hard-rock mines dates back to the late 1940s. For the first several years, they were used only occasionally, being limited to a few metal mines that experimented with crawler¬mounted front-end loaders, tractor-trailer hauling units, a few tractors for drill-compressor mounts, and utility cleanup machines. By the mid-1950s, track loaders had become commonplace in limestone mines and uranium mines on the Colorado Plateau in the United States, as well as in Canada. Use of crawler-mounted tractors as drill and compressor mounts also increased. By the end of the 1950s, rubber-tired loaders and some haulers began to replace the track-type machines and rail-mounted cars that had been in use. About 1960, the rubber-tired machines brought about a new era of underground mining mobility and flexibility, centered on a method commonly known as "trackless mining." Ultimately, many of the underground rail-type systems for loading and hauling were replaced by the trackless mining technique. ECONOMIC CONSIDERATIONS The size and nature of mineral deposits, plus ground control techniques, historically had dictated small open¬ings to the surface from many underground mines. The small mine openings led to the development of special rubber-tired loaders and haulers designed specifically for access through the small openings. However, some mines, particularly those in massive mineral deposits, are able to excavate and maintain very large openings, and some use modified room-and-pillar systems. With the large mine openings, the use of larger, more produc¬tive equipment such as that commonly found in surface mining becomes economical. In fact, productivity gen¬erally increases at a more pronounced rate than machine size increases because many of the larger machines were designed for heavy-duty shot-rock applications in surface mines and construction sites where the handling of blasted rock is common. Table 1 can be used as a very Table 1. General Productivity Comparison for Conventional Machines In Underground Use (Shot-Rock Conditions) 2.3 m3 (3 cu yd) 4.6 m3 (6 cu yd) Loader Loader Expected Surface 230 t/h 540 t/h Production (250 stph) (600 stph) Expected Underground 90 t/h 270 t/h Production (100 stph) (300 stph) Expected Total Efficiency: Surface 40%-60% 50%75% Underground 25%.-40% 30%50% Expected Useful Machine 8000 hr 12,000 hr Life Before Replacement general comparison of the production and efficiency between small and large machines. Combining greater productivity often inherent in larger machines, with reduced downtime resulting from using fully developed machines with fast parts and service backup, some mine operators have been able to reduce material handling costs appreciably while reduc¬ing manpower requirements for operators and main¬tenance men. Large mine openings increase the amount of rock that must be handled in the development work, and they sometimes increase the dilution in stopes or rooms, de¬pending upon the dimensions of the ore zone. Providing adequate space for the unrestricted operation of large surface mining machines could, therefore, lead to more waste segregation and handling costs. It could also cause greater ore dilution that would result in a lower grade of ore being delivered to the processing plant. The tradeoffs between opposing cost factors must be reconciled and balanced to achieve the best overall cost of the crude ore, concentrates, or product. EQUIPMENT MODIFICATIONS Loaders and haulers designed for surface mining are seldom used underground in their standard con¬figurations without some modifications. If done, the modifications generally are made by the equipment dealer and/or the user, and the modifications usually include one or more of the following items: 1) The exhaust stack is lowered, and its direction is changed. Usually, it is repositioned horizontally to the rear, or it is fed into the engine fan to diffuse the exhaust gases. 2) The operator's position is lowered by either lowering the seat or changing the seat to a side mount. 3) The operator controls are adjusted to fit the new operator position. 4) Other components, such as the radiator and loader tower, are lowered. 5) Special bumper guards are mounted at the base of the radiator area. 6) An exhaust conditioner is mounted and con¬nected, using either a catalytic or a water-type condi¬tioner, or both. This usually is controlled by the safety and health regulatory authority having jurisdiction. 7) The positions of other components are rearranged

Jan 1, 1982

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By E. Barnard

Tarkwa Gold Mine is located in south western Ghana, and is majority owned and operated by Gold Fields Ghana Limited. The Tarkwa CIL plant utilises a single low aspect 27' x 42' 14MW dual pinion drive SAG mill designed to mill 4.2mtpa (525tph). The plant was designed and constructed in a manner that would facilitate its expansion to 8.4mtpa (1,050tph). Since the plant was commissioned in September 2004, the SAG mill has consistently exceeded its nameplate throughput by up to 25%. Through the installation of a 26? x 36? 14MW dual pinion drive Ball mill along with additional upstream and downstream equipment, the plant will now be expanded to 12mtpa (1,500tph). This paper endeavours to outline the process and engineering design challenges along with the future construction challenges of the expansion in the midst of a fully operational plant.

Jan 1, 2008

By Richard E. Hucko

The Coal Preparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals--an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal--to establish grade- recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes--nominal minus 35 mesh (0.5 mm) and nominal minus 100 mesh (0.149 mm)--and subjected to conventional froth flotation. The froth product was then beneficiated by coal-pyrite flotation or HCMS to provide a direct technical comparison of the two processes. At minus 35 mesh (0.5 mm), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a size of minus 100 mesh (0.149 mm) , however, the performance of HGMS exceeded that of coal- pyrite flotation. The separations effected by HGMS were more efficient at minus 100 mesh (0.149 mm) than at minus 35 mesh (0.5 mm). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size, or the process has not been optimized to treat material finer than 35 mesh (0.5 mm).

Jan 1, 1981