Search Documents

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By S. M. Pickering, L. T. Gregg

Appraisal of industrial minerals beneath privately owned land requires a different approach and mindset from valuation of base and precious metals or energy minerals, and from valuation of government-owned mineral lands. First, is it the value of inground minerals or of mining rights that is being sought? Second, value to whom, the mining company, a potential investor, the mineral landowner, a lending institution, the property tax assessor, or a condemnor? Third, how should mineral value be apportioned between the land and mineral owner, and a mining company with limited years of lease-hold interest? These and many other questions must be addressed before a valuation method and Discount Rate are selected. For various reasons the Income Method is most often used, with Net Present Value calculations made for long term predicted mining income. Choice of an appropriate Discount Rate is critical.

Jan 1, 2000

By M. Irish

This paper describes the emergency water control measures used at Pegasus Gold's Zortman Landusky mine during the September 1986 flood. The amount of solution stored increased by approximately 78 165 m3 due to receiving 0.2134 m of rain in a 24 hour period. Three methods of water disposal will be discussed including continuous chlorination, batch chlorination, and reverse osmosis. A water management program will also be discussed.

Jan 1, 1988

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By Chee Theng

"In 2013, Coeur Mining had more than $55 million in general and administrative (G&A) costs and less than $100 million in cash flow. This year, its G&A costs stand at $30 million, down by more than 40 percent, its all-in sustaining costs have shrunk by more than 30 percent, and its cash flow is above $200 million. To realize this, the company aggressively reduced both its corporate overhead cost and operating cost and repaid more than $300 million in debt.The more robust balance sheet meant the precious-metals producer was well positioned to reap the rewards of an upsurge in commodity prices in the early part of 2016. Its stock price soared from $1.75 in January to $15.98 in August. Although the stock price has since dropped to around $9 due to a stronger dollar and a more hawkish Federal Reserve that recently raised U.S. interest rates, shifting the opportunity-cost argument away from buying gold and silver, Coeur remains attractive to analysts in light of its prudent spending and improved fundamentals.Focus on balanced portfolioCoeur is the largest primary silver producer and one of the largest gold-producing companies in the United States and one of the largest silver companies in the world. Incorporated in 1928, the U.S.-listed company has a total of five operations: three in the United States, one in Mexico and one in Bolivia. About two-thirds of its revenue comes from the United States.The company is conscientious about having a balanced portfolio, so no single mine accounts for more than about 30 percent of its business. Being in three different jurisdictions provides further diversification, and its revenue split of about 60 percent from gold and 40 percent from silver gives it some metals mix. This year, it expects to produce about 466 t (15 million oz) of silver and 10.3 t (330,000 oz) of gold."

Feb 1, 2017

By A. Galicia, A. Charest

The Marlin deposit is a low sulphidation Au-Ag, epithermal system, with reserves of more than five million ounces gold equivalent. Marlin was discovered in December 1998, after a nine months grassroots exploration program in western Guatemala, focused on volcanic terrains of the Sierra Madre. Before the Marlin discovery, several gold prospects were found along an east-west corridor of approximately 70 kilometers long, associated to regional faulting systems. The deposit is hosted in faults, within Tertiary andesitic rocks and bedded volcano-sediments. Host-rocks are argillized closer to the surface and propyllitized at depth. Mineralization occurs in multi-stage quartz stockworks and breccia veins.

Jan 1, 2004

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By S. R. S. Sastri, K. K. Bhattacharya, K. S. Narasimhan

Experimental results obtained on the recovery of below 0.5 x 10-3m coal fines by flotation employing geometrically similar columns of 0.056m, 0.080m, 0.100m and 0.220m diameter have been presented. The hydrodynamics of such a unit as well as its performance have been related to operating parameters to establish optimum conditions. The results have further been analysed critically in the light of the known relationship on the behaviour of similar systems to assign reasons for the critical factors established in a bid to reduce the empiricism required to be followed in the scale up of such a unit.

Jan 1, 1988

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By R. B. Berg

Montana sapphires were first discovered in alluvial deposits in the Helena area in 1865 and subsequently were discovered in other alluvial deposits in southwestern Montana and also in a lamprophyre dike at Yogo in central Montana. From about 1900 until the late 1930?s, when synthetic sapphire began to come into widespread industrial use, Montana sapphire mines produced large quantities mainly for watch bearings with lesser production for the gemstone market. The Yogo deposit is now mined for the gemstone market and two of the alluvial deposits are mined to produce sapphires for the fee-sieving of sapphire-bearing gravel and for the direct sale of gemstones. The generally pale-colored sapphires from the alluvial deposits in southwestern Montana are heated to enhance their colors whereas the generally blue sapphires from the Yogo deposit require no treatment. Markets for sapphires from both the alluvial deposits and the Yogo deposit are strong. In spite of reported historic production in excess of 70 tonnes, mineable resources appear to remain at most major deposits. Also abundant untested lamprophyre dikes in central Montana may host sapphires similar to those at the Yogo deposit.

Jan 1, 2009

By G. T. Adel, J. D. Miller, C. L. Lin

Washability analysis determines the maximum separation efficiency that can be achieved in the operation of coal preparation plants. Unfortunately, there are no on-line techniques for determining this most fundamental information. It now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. This paper presents the results for the development of a CT-based, on-line coal washability analyzer. The development of appropriate hardware and software necessary to adapt a CT analyzer for use in determining coal washability is discussed. Testing of the analyzer using well-characterized coal samples is presented.

Jan 1, 2000

By C. Bryce

Rhenium is primarily recovered as a byproduct from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations, and this represents a potential new rhenium source. Freeport-McMoRan (FCX) has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita Mine has demonstrated the technical and financial feasibility of this new process. Copper heap leaching dissolves more than just copper from the copper ore. Several metals can be identified in leach solutions at concentrations of financial interest, rhenium in particular. Rhenium spot prices ranged from a yearly average of $1,070/kg ($483/lb) in 2005 (Magyar, 2008) to $10,400/kg ($4,706/lb) in 2008 (Polyak, 2013). The spot price in September 2013 was approximately $3,000/kg ($1,357/lb) of rhenium (Metal Bulletin, 2013). Several facilities at Freeport-McMoRan have very low rhenium concentrations in their copper leach solutions, ranging from 0.1 to 0.7 mg/L. The large quantity of solution available, if coupled with an attractive rhenium price, means that the rhenium contained in leach solutions may represent a significant value if a method of extraction could be developed. Testing has confirmed that rhenium adsorbs onto activated carbon much more selectively than other metals in the pregnant leach solution (PLS). A 100-gpm pilot plant was constructed to verify the lab-scale results on a larger basis and establish operating parameters for a full-scale operation. This report summarizes the initial technology development and pilot plant operation.

By Anthony Leddin, Gillian Dooley

This paper is concerned with mineral policy in Ireland and how it might be improved to encourage more exploration and investment in mining in the country. The approach is to first outline the main desirable characteristics of a comprehensive national mineral policy document. This aspirational document is then used to assess the current regulatory, legislative and fiscal frameworks for mining in Ireland. The analysis also contains a brief account of the history, structure and characteristics of the mining industry in Ireland. The main focus of the paper is to identify those aspects of the existing framework that erode Ireland’s attractiveness to mineral investment and to suggest policy improvements.

Jan 1, 2005

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014

By Enrique Hermana, Raymond F. Dalton, Raymond Price, Barry Hoffman

Introduction Chloride leaching of sulfidic ores has been known about for 100 years. It is recognized as a highly efficient process to produce concentrated leach solutions. Despite this, chloride leaching found little practical application until recently because of the highly corrosive nature of concentrated chloride solutions. This situation changed with the advent of modern construction materials such as GRP, polypropylene, butyl rubber, etc. And in the past 20 years, research has burgeoned in the area of chloride hydrometallurgy. The research impetus stemmed from the belief that chloride leaching can provide an alternative to smelters for treating conventional copper concentrates. In addition, chloride leaching was thought to be suitable for on-site refining of copper at small tonnage operations located in remote areas. And chloride leaching was seen as a logical choice for treating unusual or complex concentrates that smelters could not handle. Underpinning these beliefs is the attraction of chloride-based hydrometallurgical processes for sulfidic ores. Sulfur is liberated in the environmentally acceptable elemental form rather than as sulfur dioxide. Consequently, sulfidic copper ores have received much attention. A review of Edmiston in 1984 describes 12 chloride-based processes. All managed to progress past the "laboratory beaker" stage of evaluation. In nine of these processes, copper is recovered electrolytically. Key features of these processes are summarized in Table 1. Table 1 shows that the processes must include a copper solvent-extraction step. Only these processes produce a clean copper electrolyte capable, with no further refining, of directly producing high quality cathode copper. The ICI/Elkem process is the exception here. The rest of these processes use o-hydroxyaryloxime reagents for the solvent extraction of copper and are constrained by the performance of these reagents. This is governed by hydrogen ion concentration (Equation 1). The practical result is that only relatively dilute copper solutions can be treated (Canmet, Phelps Dodge), or careful pH control or adjustment is necessary (Minimet Recherche, B.H.A.S.). This negates one of the attractive features of chloride leaching - its ability to produce very concentrated copper solutions, up to 40-45 gl-1. [ ] In all four processes using o¬hydroxyaryloxime extractants, solvent extraction transfers the copper from the chloride to the sulfate medium. To minimize cross-contamination of the two anions, the loaded organic solvent has to be scrubbed to remove the chloride ion. This represents an additional complication in the solvent extraction circuit. And it

Jan 1, 1988

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By Paul D. Dupree

Introduction Trapper mine is a dip-line strip coal mine, located about 10 km (6 miles) southwest of Craig, CO. The mine provides the Craig Generating Station, operated by Colorado-Ute, with about 2 Mt (2.3 million st) of coal annually. The Trapper mine is situated on a hillside that climbs in elevation from 2 to 2.5 km (6500 to 7400 ft) at average grade of 15%. The coal seams dip at about 16% down-grade and they outcrop near the top of the hillside. They exceed maximum stripping depth in 1 to 1.7 km (3500 to 5500 ft) of pit length. Stripping in the three existing pits is performed with three Page 752 23 m3 (30 cu yd) walking draglines. Two of the pits are currently being cast blasted. Until the active cut, the Derringer pit was cast blasted only where the lower mined seam exceeded stripping capabilities and the pit was a single seam operation. Now, a 9-m (30-ft) interburden bench has been incorporated into the stripping plan. This bench protects the first seam of coal from shear when the overburden is cast blasted. The cast blasted section of the 1.6 km (53,000 ft) long pit has been increased from the 457 m (1500 ft) casted previ¬ously to 1 km (3500 ft). High speed films show the coal losses due to shear of the blast are minimal. The pit width in Derringer pit is 61 m (200 ft). This is necessary for efficient spoil side stripping of a relatively thin interburden in the two-seam section of the pit. The Enfield pit is entirely cast blasted. The single seam pit is 46 m (150 ft) wide, 1.1 km (3600 ft) long, and varies from 15 and 46 m (50 and 150 ft) in overburden depth. The overburden strata at the mine consists of medium-hard layers of sandstone, shale, and

Jan 1, 1987